The Landwalker 22″ Complete Skateboard has a sturdy 7 layer Canadian maple deck. It’s best for downhill, U table and slider because of its enormous stability. This board is best for teens and adults. It comes with Abec 7″ Bearings, PU wheels, Black Grip Tape, and hardware. It measures 79 x 20 x 10 cm. This board is an awesome gift for Christmas or Halloween.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Made with bamboo and fiberglass, this board is tough, flexible and ready for anything. The construction is designed to feel and act like a snowboard. The drop-through design is perfect for freestyle longboarding, commuting, carving, pumping and more. It gives you better stability and more wheel clearance. The board is definitely best designed for carving but tricks and kicks are easily done as well.

Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
So you want to know how to ollie? Be warned, it’s not for the faint of heart, and a lot of people have tried and failed and tried some more and still failed and then eventually thrown their boards into a wall out of frustration (I have no idea who those people are). It’s by no means an easy skateboard trick, but if you want to know how to ollie, start with these simple tips:
The fact that it has nice and attractive prints also makes it a fashion skateboard. You can use it to show not only your passion in the sport but also your fashion sense. It is also equipped with a high-density emery surface known for being both waterproof and non-slip. With that, you have a hundred percent assurance of your safety when you are riding on it.
Before learning it, do have your riding basics down. Meaning you are very comfortable riding it around and doing kickturns and not be pushing mongo. Best to learn it whilst stationary with your wheels on a crack so that you don't move and slip out so much. I don't recommend doing it on grass or carpet cos when you pop the tail, it's gonna be absorbed by the floor and when you start doing it on pavement, your muscles will memorize a different way of doing it. So nope, no easy way out i guess.

New Arrivals Men Backpacks & Bags Watches Wallets Sunglasses Hats Socks & Boxers Beanies Bandanas Belts Cologne Grooming Sun Care Jewelry Shoe Care SHOP ALL Women Backpacks Bags & Wallets Hats Belts Jewelry Sunglasses Watches Hair Accessories Socks & Tights Beauty SHOP ALL Phone & Tech Phone Accessories Tech Accessories Cameras Backpacks & Bags Backpacks Luggage & Duffle Bags Mini Backpacks Fanny Packs Lunch Bags Room & Home Kitchen & Drinkware Towels Inflatables Decor Pillows & Bedding Desk & School Supplies Novelties Stickers Patches Pins Keychains Air Fresheners Toys Toys & Plushes Blind Boxes Games Books Costumes & Masks Skateboards Longboard Skateboards Cruiser Skateboards Complete Skateboards Skate Accessories
A rushed take-off might be the problem here. Steps 2-4 of this trick tip could help you out. In order to make your feet “stick” to the board, you have to do the movement fluidly. But don’t stress yourself out! You should rather start with some preliminary exercises until you feel safe while ollieing. It is also important to pull your foot up to your board’s nose in a straight manner to prevent it from spinning.

Skateboarding Trick Tip: How To Ollie The Easiest Way & Common Ollie Problems,How to ollie on a skateboard,how to ollie on a skateboard,how to ollie higher,how to ollie while moving,how to ollie on a skateboard for beginners,how to ollie while moving for beginners,how to ollie stairs,skateboarding tricks,skateboarding ollie tutorial,skateboarding ollie slow motion,how to ollie up a curb,how to ollie while moving,overindulgingSkateboarding Trick Tip: How To Ollie The Easiest Way & Common Ollie Problems


Skateboard hardware is used to connect the skateboard trucks to the skateboard deck. Skateboard hardware refers to the bolts and locknuts used when building a board. The bolts can have an Allen or Phillips head. Skateboard hardware comes in many different lengths, and often includes one different colored bolt so that the rider can mark the nose of their board.

Before we show you how to ollie, let’s get familiar with the legends that brought this skateboard trick to the masses.  If it were a person, the history of ollie would start way back in 1974, when Alan Gelfand got his first skateboard from his father after his family moved to Hollywood, Florida from New York state. It didn’t take him too long to get the hang of it; he won the South Florida Skateboard championships two years later.
go with friends like most do, or at least with friends that support what your doing. Im 26 yrs old,I am a solo skater in elk city Oklahoma and the skate community is small, but we have a park , but in the smaller community skaters clique up I didn’t grow up here so I’m left out. I learn a I can online and practice little bit s out of the day when I have time from both jobs I work, I just don’t get a lot of beef cause I ignore them and do my own thing , but I’ve noticed my tricks that I land alone fairly easy they get difficult in the presence of others for some reason Being standoffish and skate with a lil aggression you’ll be alright, just don’t give up man at all costs do not give up.

The board also boasts of its reasonably small size and lightweight nature, making it easy to control and ride. In addition, carrying it wherever you want to go is also much easier because of its lightness. It is flexible enough that it can accommodate the needs of different kinds of users, including cruisers, travelers, beginners, expert riders, and kids.
GREAT board. Great design graphics. The boards deck has a real POP to it that makes it GREAT for tricks and a AWESOME beginner board. Only problem is It's super slow and requires a lot of work to maintain speed or to pick up speed period. A simple $20 wheel barring upgrade will fix that and BOOM PERFECT board, PERFECT caved in deck. Only 4 stars because of the lack of speed. I prefer my boards ready out of the box already pre-upgraded, but for the price, no point in complaining. Like almost all new boards, u have to ajust the wheels and the flex of the board to customize it to your liking. You won't regret it. But order it with some "Lucky" or "Red bearings" and your set.
The Wasatch Imports Good Skateboards is the ultimate compact and complete street board that is ready-to-go. It is great for exercise and fun. It is very portable and perfect for all skill levels. It has a variety of awesome vintage color combinations that you can choose from. It is made of topline construction, with a high-density plastic deck, 59mm super smooth wheels, ABEC7 bearings, and solid aluminum trucks. It measures 22″ long and 6″ wide and weighs 4 pounds. It has a  full manufacturer’s lifetime warranty on all parts, pieces, and materials. It has a weight limit of 200 pounds which can ensure that bigger skaters can join the fun.

With Enkeeo 22 Inch Cruiser Skateboards, you can cruise in style.  It has a dimension of 22 x 6 inches.  It comes with 3″ Black Coated Habitat trucks, Black 60mm Smooth wheels, and Abec11 bearings. It’s ready to ride and you can even personalize the tail of the board for free with a limitation of 10 Characters only. It has 30 days warranty and is manufactured in California.  It has a perfect 5 rating on Amazon.


Shock pads are made of polyurethane and rubber. They are very similar to risers but vary in the fact that their sole purpose is to cushion the board from the trucks. Since the trucks are metal and the board wood, whenever the board hits the ground after doing a trick, the energy goes through the truck to the board ─ this has caused boards to crack, split, or even break in half, and shock pads were created to prevent this.
A skateboard is moved by pushing with one foot while the other remains on the board, or by pumping one's legs in structures such as a bowl or half pipe. A skateboard can also be used by simply standing on the deck while on a downward slope and allowing gravity to propel the board and rider. If the rider's leading foot is their right foot, they are said to ride "goofy;" if the rider's leading foot is their left foot, they are said to ride "regular." If the rider is normally regular but chooses to ride goofy, they are said to be riding in "switch," and vice versa. A skater is typically more comfortable pushing with their back foot; choosing to push with the front foot is commonly referred to as riding "mongo", and has negative connotations of style and effectiveness in the skateboarding community.

Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
×