In 1977, skate parks began cropping up all over the place, including Skateboard USA, where Gelfand began to spend most of his time. His buddy, Scott Goodman, is the one who gave Gelfand the nickname of “Ollie” and dubbed his aerial lipside the “ollie-pop.” Pictures of Gelfand during this time period clearly show him getting airborne and performing the trick associated with his name today.

The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
BRANDS Acembly adidas Amuse Society Asphalt Billabong Birkenstock Blue Crown Brixton Burton Calvin Klein Captain Fin Champion Charles and a Half Converse DGK Diamond Supply Co. Dickies Dr. Martens Electric Element Elwood Ethika FILA Fox Full Tilt G Shock Grizzly Herschel Supply Co. HippyTree Hoonigan HUF Hurley Hydro Flask Imperial Motion Ivy & Main JanSport Kendall & Kylie King Ice La Familia Last Call Co. Levi's Lira Loser Machine Lost LRG Neff New Balance Nike SB Nixon O'Neill OP Others Follow Patrons Of Peace Penny Pink Dolphin Popsockets Primitive Skateboarding PSD Puma Quiksilver Rainbow Rastaclat Ray Ban Rebel8 Reebok Reef Riot Society Rip Curl Roark Roxy RSQ Russell Athletic Rusty RVCA Salty Crew Santa Cruz Sky and Sparrow Soda Spy Stance Suavecito The North Face Timberland Tommy Hilfiger TOMS Under Armour Vans Vissla Vogue Eyewear Volcom Von Zipper Young & Reckless VIEW ALL BRANDS
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.
If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.
The Rimable Complete 22″ Skateboard is the most compact street board that are ready-to-use.  It is best for exercise and fun, and very portable.  There are five colors that you can choose from Black, Blue, White, Purple, and Green.  It has high-quality construction, with a high-density plastic deck.  It features extremely smooth 59mm wheels along with ABEC7 bearings and solid aluminum trucks.  It measures 22″ long and 6″ wide and weighs 4 pounds.  It has the best rating of 4.3 on Amazon.
One foot on the tail, (by foot I mean the ball of the foot which is just behind the big toe) the other foot is about an inch behind the bolts(screws) for the front truck. Basically, the back foot quickly pushes the tail down, and right when the tail of the board strikes the ground, the back foot jumps up… the tail of the board will follow up with the foot when the front foot slides forward slightly, which pivots the tail of the board upwards. Since the front truck comes off the ground first, getting the back truck up is the trick.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.

Velocity Boards Retro Banana Skateboard is a 22″ Complete Board Set with 6″ Aluminum Trucks, ABEC-7 Bearings, High-Quality Wheels, and Bushings. It is designed for maximum grip. The Deck measures about 22 x 6 x 4″. The truck Axle has a Width of 6″ and the Truck Hanger has a Width of 3″. It has a maximum load capacity of 176 lbs. (80 kgs.) It is best for skaters who are 6 years old and Up. It has an average Amazon rating of 4.7.


But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.
Skateboarding is all about creativity and finding new challenges. A great way to explore skateboarding is to ride different shaped boards, wider trucks, and different size wheels. As you progress and start to ride new terrain and skate different kinds of spots, you may find one wheel size or board shape works better for you than another. There’s no wrong or right anything. There are no rules. Except for maybe one, and that is to keep skating. Skate as often as you can. Never is this more true than in the beginning while you’re developing your style and fundamentals.
Go for the low truck profile if you want to obtain additional stability when you do flip tricks. It also works well for small wheels. The mid-sized trucks are good for all-around use, especially in streets and parks. You can also choose the high-sized trucks that are good for carving and cruising, which is the reason why they are perfect for huge wheels.
Plan B sells boards with overall reliable attributes. They offer decks made from seven-ply wood. Powell is a longstanding company that founded the legendary Bones Brigade team, which kick-started Tony Hawk's career. Their skateboard designs change annually, but always look cool. Tony Hawk’s skate company is called Birdhouse. Their decks feature bird themes and have a thicker sixth layer of wood that makes it easier to jump and do flip tricks, which is ideal for vertical-style skateboarding. For environmentally-conscious skaters and fans of Bam Margera, buy a board from Element. They have variety on the technical side with their seven-ply boards and Helium decks. Their skateboards are made with an air pocket to be lightweight.
Penny Skateboards make premium plastic skateboards, letting you chase the sunshine and good times. Available in a great range of colours, including pastels, brights and prints, there’s sure to be a Penny Skateboard to match your unique style. Prefer to customise your ride? Head to the hardware store to update your griptape and wheels, making your Penny look brand new! Embrace the Penny lifestyle, join in the fun and find your favourite Penny products for sale online.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.
×