Skateboarding started in California in the 1950s. The first skateboards were made from roller skates (attached to a board). Skateboarding gained in popularity because of surfing; in fact, skateboarding was initially referred to as "sidewalk surfing". Initially, skateboards were handmade from wooden boxes and planks by individuals. As the sport became more popular, companies started manufacturing skateboards. Boards are also continuing to evolve as companies try to make them lighter and stronger or improve their performance.
I have skated for about 7 years i took a 2 year break. I have had about 50 boards and from that id say this board is ok seeing as iv had zero's break day one. if your newer to skateboarding and you dont mind the cost i would say go for it. For more hardcore skaters there are some things you should know about this board. im not 100% about the trucks day one just doing kickflips 360 flips smaller gaps.. its a bit shaky i dont think these trucks are make for stairs or big gaps but they will do till i have the cash for some thunders. the bearings are hit or miss one is on its way to being blow out the others seem to be fine. I got to say i really like the wheels there was not much info on them but they are smaller and harder and i love harder wheels i hit a nice nolie 360 first try and the sound of the slide took me back to the good days. As for the board i cant judge it off one day of skating but from the looks of it its not a knock off. Here are some tips for buying a board online. find real skaters in the comments dont buy a board because a dad said his kid loves it. When you get the board go over all the parts and look over your board well make sure there are no defects in the board. make sure the board is not waterlogged a few taps should tell you. if you dont know anything about skateboards ask a friend to help and if you find any defects send it back right away. I hope the review helps you.
To summarize, a skateboarder's feet need to do two things successfully to complete an ollie. They need to provide a changing force to move the board correctly (so that the combined force of gravity and the skater's feet add up to the green arrows above), and they need to provide different amounts of force with each foot (shown by the red and blue arrows above) to steer and turn the board into the right orientation.
Grip tape is a sheet of paper or fabric with adhesive on one side and a surface similar to fine sandpaper on the other. Grip tape is applied to the top surface of a board to allow the rider's feet to grip the surface and help the skater stay on the board while doing tricks. Grip tape is usually black, but is also available in many different colors such as pink, red, yellow, checkered, camo, and even clear. Often, they have designs die-cut to show the color of the board, or to display the board's company logo. Grip tape accumulates dirt and other substances that will inhibit grip, so use of a grip eraser or rubber eraser is necessary after riding through mud or with dirty shoes.
Choosing a skateboard deck can be approached in a few different ways: you can choose your board based off the graphic, the brand, the shape, the width, or even the color. For most skateboarders, it’s a combination of all these factors, but if you’ve never skateboarded before, you may not know what shape, width, or brand you like best. In this case, choosing your favorite graphic would make total sense.
Radiate Ride Good Skateboards are made of 7-ply maple construction with epoxy resin glue. It features 356A heat-treated cast aluminum high performance 5.0 trucks with grade 8 kingpins and axles. The super high rebound 99A PU wheels with grooved running surface provide better traction and abrasion resistance. The Abec 5 high precision speed bearings offer precision performance and a smooth ride. It has an 80 grit durable color matched grip tape with transparency. It is completely assembled and ready to go. This product has a 4.3 rating on Amazon.
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it.
GREAT board. Great design graphics. The boards deck has a real POP to it that makes it GREAT for tricks and a AWESOME beginner board. Only problem is It's super slow and requires a lot of work to maintain speed or to pick up speed period. A simple $20 wheel barring upgrade will fix that and BOOM PERFECT board, PERFECT caved in deck. Only 4 stars because of the lack of speed. I prefer my boards ready out of the box already pre-upgraded, but for the price, no point in complaining. Like almost all new boards, u have to ajust the wheels and the flex of the board to customize it to your liking. You won't regret it. But order it with some "Lucky" or "Red bearings" and your set.
Almost no one lands an ollie on their first try. Repetition is the most important part of learning how to ollie. Once you learn how to do an ollie, you can try doing them while rolling. Learning is one of the funnest parts of skateboarding. After you learn ollies, you can move onto 180s, Pop Shove-Its, and flips. Soon a whole world of tricks will open up.
My fiancee purchased this via my account and he says that it has good concave shape and pop.Assembling was fairly simple, easier if you have a box cutter on hand to help with laying the grip tape. The deck was the best part but the bearings were good too. He thought the bushings were the worst, after about two hours of skating, both bushings were crushed and stuck in one direction. He's been skating for almost 13 years. Hope this helps!
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air. While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.
Hey, welcome to the blog! My name is Billy and I've been a skateboarder now for over a decade. I know how hard it can be when learning new tricks. That’s why I decided to put up this site – to help beginner skaters find success. If you want to learn how to land skateboard tricks that will shock and amaze your friends, you've come to the right place. Bookmark this blog and come back often to learn how you can skateboard like a pro.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
Shock pads are made of polyurethane and rubber. They are very similar to risers but vary in the fact that their sole purpose is to cushion the board from the trucks. Since the trucks are metal and the board wood, whenever the board hits the ground after doing a trick, the energy goes through the truck to the board ─ this has caused boards to crack, split, or even break in half, and shock pads were created to prevent this.
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car. It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings. It is ready to use and you can easily store it in your backpack. It has an average rating of 4.5 on Amazon.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.