So the proper foot placement for the ollie is with the ball of your back foot horizontal on the tail of your skateboard.  And your front foot centered on your board right behind the front trucks.  You may find that moving your feet around in different positions are more comfortable.  This is fine,  everybody can learn how to skateboard their own way.
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
You can learn to ollie while standing stationary, or while your skateboard is rolling. Ollying while standing still works the same way as while rolling, but I think rolling ollies are easier than stationary ollies. If you would like to learn to ollie with your skateboard stationary, you can place your skateboard on some carpet or grass to keep it from rolling. If you prefer to learn to ollie while your skateboard is rolling, don’t go very fast at the start. Whichever way you learn to ollie, once you feel comfortable you should try to ollie the other way as well.
    Almost no one lands an ollie on their first try.  Repetition is the most important part of learning how to ollie.  Once you learn how to do an ollie, you can try doing them while rolling.  Learning is one of the funnest parts of skateboarding.  After you learn ollies, you can move onto 180s, Pop Shove-Its, and flips.  Soon a whole world of tricks will open up.

This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
go with friends like most do, or at least with friends that support what your doing. Im 26 yrs old,I am a solo skater in elk city Oklahoma and the skate community is small, but we have a park , but in the smaller community skaters clique up I didn’t grow up here so I’m left out. I learn a I can online and practice little bit s out of the day when I have time from both jobs I work, I just don’t get a lot of beef cause I ignore them and do my own thing , but I’ve noticed my tricks that I land alone fairly easy they get difficult in the presence of others for some reason Being standoffish and skate with a lil aggression you’ll be alright, just don’t give up man at all costs do not give up.

It’s not just standard deck sizes that are available for creating or replacing your board. You can just as easily get a great longboard deck to work on in your basement or garage. One of the best and best reviewed options out there is the Loaded Boards Poke Longboard Skateboard Deck. This standard-design longboard deck has it all to help you make the ideal board. 
The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
The fact that it has nice and attractive prints also makes it a fashion skateboard. You can use it to show not only your passion in the sport but also your fashion sense. It is also equipped with a high-density emery surface known for being both waterproof and non-slip. With that, you have a hundred percent assurance of your safety when you are riding on it.
I have been doing ollie’s for about a year to a year and a halve, but thats not the problem. My problem is the board turns when i ollie, i cant help it, i am starting to go into harder ground (ollying off ledges and ollying stairs) but i cant land and ride away because my board has turned in a 45 degree angle and it jerks me off the board, Please help in all you can, cheers mate.
There are other types of ollies that you can do either alongside or combine with the ones listed above, like the tailgrab, indy grab, melon grab, stalefish, tweak, and dolphin nose. All of those skateboard tricks are performed more or less how they sound, but you might want to watch some videos on youtube to see a pro in action (as well as awesome cat videos).
When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.
Learn how to ollie off of a ramp: Ramps are a LOT of fun to ollie off of, but they are also a great way to break something if you don't know what you're doing! I have a cousin who almost lost his arm because of how nastily he broke it while ollying off a ramp. But don't let that scare you - if you know what you're doing, ollying off ramps is great!

Taotao Girls Skateboards comply to United State Consumer Product Safety Commission (CPSC) Standard.  It has a 24″ X 6″ Maple Double Kickside Deck. It features 608Z Bearings, 3.5″ Plastic Truck & Base, and 50 x 30 mm PVC Wheels.  The Safety helmet, Knee and  Elbow Pads also comply to CPSC Standard.  It has a Cool Pink Aloha Graphic Design with an Amazon rating of 4.3.
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve

When learning it, you will, slip and fall. Feel like an idiot doing something over and over again and not getting it, feel fear bcos you don’t know what's going to happen to you once you pop the tail, jump and slide your foot and then you land. Will you land on your board, will you be on the pavement? Will you slip out, will u kick the board away, will you land primo? No one knows but you gotta try it out and find it out yourself. Whatever it is, don't give up cos it's the strength to persevere, be crazy persistent to achieve and most of all being patient in learning and progressing that let's you earn the skateboarder title for your ownself.
So now that you have an idea of what size and shape board you like, it’s time to choose a brand. A popular size is an 8.5 skateboard deck. If you were looking for a size 8.5 skateboard deck, you could narrow the decks offered on CCS.com to fit in the 8.25 - 8.5 range. This will show you all the boards in that range, and significantly reduce the boards you have to look through. Now, if you don’t have a preference on board brands, find a graphic you like and you’re all set. If this is your first skateboard or are still learning about what wood and brands you prefer, we recommend checking out a CCS Skateboard. They give you a bang for your buck, that's for sure.

This set-up is awesome for its price!!!! The wheels are nice and smooth (a little too big for my liking, but still good). The bearings are average (I replaced them with bones REDS). The trucks are nice and sturdy, but the bushings are kinda weak. The board is AUTHENTIC and of good dimensions. Finally, the griptape...they're all pretty much the same it's just the brand name that's different, so it doesn't matter it's all good. I would buy from this seller over and over again!!!!!!!
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.

So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
This board includes professional assembly. All Krown skateboards arrived assembled and ready to ride straight out the box. The Rookie model includes heavy duty Aluminum 5.0 trucks, 52mm 99A high-rebound urethane wheels, precision speed Abec 7 bearings, high tensile phillips head mounting hardware, and 80 grit black grip tape. Each component meets the industry standards and are a common choice of skaters worldwide.
Choosing a skateboard deck is a great place to start when building a complete skateboard. Unless you have experience riding a shaped board - something a little more retro or unusual, we recommend you start with a popsicle shape. CCS carries over 60 different skateboard deck brands that sell this popular popsicle shape. If you have questions on what size you should ride or have any other questions about building a complete, we recommend you check out our Skateboard Buyer’s Guide. Here, you’ll find helpful how-to’s for choosing a skateboard decks, skateboard trucks, skateboard wheels, skateboard bearings, and skateboard components. This guide explains every part of a skateboard and helps you choose which sizes and styles to best suit your needs.
Pop the board in the air – The reason you jump up into the air in the first place is because you’re slamming the back end into the ground (don’t worry, your board is made to take the abuse). It’s the same motion you would do if you were standing near the board and wanted to pop the board up into your hands, except this time, you’re standing on top of it. As soon as you feel the board pop into the ground, kick your front foot up into the air at the same time. The timing on this is important: kick too early and you won’t go anywhere, kick too late and your board will fly out from underneath you.
Sizing plays an important role in the performance of any deck. A large majority range in size from 7.75" to 8.5" in width. These will provide a great platform for shredding any obstacle and will excel in street and skatepark environments alike. For those who prefer a smaller board, decks are offered down to 7.5" in width- benefiting people with smaller feet or the technical skater. Conversely, those looking for a wider board will enjoy our selection ranging up to 8.9" wide. Larger decks will accommodate those with very large feet, as well as offer an amazing experience for cruising and shredding large ramps and transitions.
My son seems to have a lot of fun riding this skateboard. He will be out there doing tricks for hours. One evening when he took a break, I decided to see if I could still ride. When I took off down the driveway, I could feel how smoothly the wheels rolled. I used to have to pay extra for wheels like this when I was his age. Lost in thought, I coasted faster, and my neighbour didn't see me when I shot out of the driveway. Even though this thing flew several feet in the air, bounced, and came to rest more than 20 feet away, it had no visible damage! Not so for me. I loved the skateboard, but am now recovering from two broken ribs, torn neck cartilage, and a cracked pelvis. Still, this board rides like a dream!

The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.
I have skated for about 7 years i took a 2 year break. I have had about 50 boards and from that id say this board is ok seeing as iv had zero's break day one. if your newer to skateboarding and you dont mind the cost i would say go for it. For more hardcore skaters there are some things you should know about this board. im not 100% about the trucks day one just doing kickflips 360 flips smaller gaps.. its a bit shaky i dont think these trucks are make for stairs or big gaps but they will do till i have the cash for some thunders. the bearings are hit or miss one is on its way to being blow out the others seem to be fine. I got to say i really like the wheels there was not much info on them but they are smaller and harder and i love harder wheels i hit a nice nolie 360 first try and the sound of the slide took me back to the good days. As for the board i cant judge it off one day of skating but from the looks of it its not a knock off. Here are some tips for buying a board online. find real skaters in the comments dont buy a board because a dad said his kid loves it. When you get the board go over all the parts and look over your board well make sure there are no defects in the board. make sure the board is not waterlogged a few taps should tell you. if you dont know anything about skateboards ask a friend to help and if you find any defects send it back right away. I hope the review helps you.
Skateboarding is a very individual activity. There is no right or wrong way to skate. Skateboarding still hasn't stopped evolving, and skaters are coming up with new tricks all the time. Skateboarding has gone through its ups and downs over the years. However, since 2000, due to attention in the media and products like skateboarding video games, children's skateboards and commercialization, skateboarding has been pulled into the mainstream. As more interest and money has been invested into skateboarding, more skate parks, better skateboards have become available. In addition, the continuing interest has motivated skateboarding companies have to keep innovating and inventing new things. In 2020 Skateboarding will appear for the first-time in the Olympics in Tokyo, Japan.[4]
New shoes + new board + new grip tape isn’t going to help anything you need to reed what is above bro its an easy how to….bend down push your back foot down make sure the tail snaps off the ground and slid your front foot forward in one swift motion you’ll get it…iv been skating 11 years and its taken me this long to finally land kick flips regularly heel flips and varials my tres are 1 outa 10 still so I practice every day and someday ill be able to land it regularly when I want skateboarding takes alot of patients ALOT so dont think you’re going to learn everything over night just sayin
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
Learn how to ollie off of a ramp: Ramps are a LOT of fun to ollie off of, but they are also a great way to break something if you don't know what you're doing! I have a cousin who almost lost his arm because of how nastily he broke it while ollying off a ramp. But don't let that scare you - if you know what you're doing, ollying off ramps is great!
×