Before learning it, do have your riding basics down. Meaning you are very comfortable riding it around and doing kickturns and not be pushing mongo. Best to learn it whilst stationary with your wheels on a crack so that you don't move and slip out so much. I don't recommend doing it on grass or carpet cos when you pop the tail, it's gonna be absorbed by the floor and when you start doing it on pavement, your muscles will memorize a different way of doing it. So nope, no easy way out i guess.
Any serious skateboarder will tell you that the ollie is the most fundamental skateboard trick. In fact, it's probably the first trick that you'll learn on your skateboard. They’re great for getting over obstacles, moving around on your board, or just looking cool. Know the right way to move your feet on the board and with a little bit of practice, you can learn to pull off the perfect ollie.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
The deck is expertly constructed with a vertically laminated bamboo core and bamboo veneer exterior, all attached with triaxial glass and epoxy as well as a course grip tape top. The grip tape is arranged in an unusual and stylish, yet functional design. The 34-inch board features a 13-degree nose angle and a 18-degree tail angle. With its directional shape, you’ll easily be able to cruise on this board or pull a few tricks. It is a lightweight and flexible deck.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air. While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.