Since its humble beginnings, Element was created out of passion and an unwavering dedication to making a positive difference. The tree continues to grow while it respects its deepest roots and embraces the landscape of skateboarding, and the lifestyle that surrounds it. From team riders to advocates, and product to marketing, Element is all inclusive, whose mission is to lead not follow, and leave an imprint deep enough, that it continues to make the world a better place.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Velocity Boards Retro Skateboards is a complete 22″ Banana Skateboard. It includes 6″ Lightweight Aluminum Trucks, High-Speed ABEC-7 Bearings, High-Quality Wheels & Bushings and Hardware. It has a Unique Textured Waffle Pattern on Deck and is designed for Maximum Grip. The Deck measures about 22 x 6 x 4″. It has a 6″ Truck Axle and a 3″ Truck Hanger. It has a maximum weight capacity of 176 lbs. (80 kgs.). It is great for all skaters who are 6 years old and above. It has an Amazon rating of 4.7.
The Landwalker 22″ Complete Skateboard has a sturdy 7 layer Canadian maple deck. It’s best for downhill, U table and slider because of its enormous stability. This board is best for teens and adults. It comes with Abec 7″ Bearings, PU wheels, Black Grip Tape, and hardware. It measures 79 x 20 x 10 cm. This board is an awesome gift for Christmas or Halloween.
The skater can gain greater clearance from the ground by jumping higher, popping faster, sliding the front foot farther forwards (starting the jump with the front foot farther back), and pulling the legs higher into the chest to raise the feet higher. Skaters attempting record-setting ollies even contort the legs so that board and feet are not directly below them, allowing the board to rise at or just below the level of the pelvis.
For sale I have a Powell peralta old school ripper complete red and black with 169mm independent blackout trucks blue cambria 3md 62mm wheels and bones reds bearings The deck has only been skated twice with minor scrapes on the tail and wheel wells I added the independent blackout 69mm trucks and the Cambria wheels im selling it because I’m moving in a different direction I’m building a longboard for myself for this summer anyway the deck is a reissue ripper you can’t get it anymore great overall skater very durable
Ollie 180: an Ollie where the skateboarder and the skateboard spins 180 degrees after leaving the ground. Both the skateboarder and the skateboard rotate in the same direction (Frontside or Backside) with the skateboarder's feet sticking to the skateboard. This trick is usually referred to as a frontside or backside 180, or less frequently and more popular with older skateboarders and/or when performed on a bank/quarterpipe, a frontside / backside ollie
In this modern era, manufacturers are incorporating hi-tech processes and top-shelf materials into the construction of the skateboard. Companies such as Almost have several versions of hi-tech decks such as the Impact, Double Impact, and Uber Light Series. Element makes Highlight decks with inlayed fiberglass beams, and Foundation has its signature Fiberprime decks. Other manufactures such as Flip, Habitat, Plan B, Skate Mental, and Zero offer boards with high-end P2 Construction. Hi-tech decks differ from traditional 7-ply Maple in that they are inlayed with Carbon Fiber, Fiberglass, Poly Ply, or Kevlar to produce a stronger skateboard with more pop. For more options, head over to our stellar selection of Hi-Tech Decks! Although hi-tech decks have made a strong presence within the market, standard 7-ply Maple remain the gold standard. This is due to the solid feeling and pop afforded through layering 7 Maple wood veneers together. The large majority of skateboard decks offered are constructed of 7-ply Maple. Most board manufacturers offer both high-tech decks and standard 7-ply Maple. No matter what you desire, CCS offers a complete selection in multiple sizes, shapes, and construction types!
Here we have an original Z Jimmy Plumer model. It has some handling scuffing from being around for several decades, but displays great. Grip has no holes at trucks which leads me to believe it’s never had any mounted. This is one heavy fiberglass mamma jamma. Get this piece of history at a fair price. I will throw in free priority insured shipping for the con us. Everywhere else at actual cost. Thanks for looking.
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
A skateboard deck is made up of curved layers of wood that are combined with glue. Then, the skateboard deck is trimmed down to a board shape that is practical. Trucks are typically made of aluminum or other metal alloys. They are made by melted metal formed by a mold and later drilled into the skateboard deck. The wheels are formed the same way, but with polyurethane. They are attached by ball bearings to complete the product.
My fiancee purchased this via my account and he says that it has good concave shape and pop.Assembling was fairly simple, easier if you have a box cutter on hand to help with laying the grip tape. The deck was the best part but the bearings were good too. He thought the bushings were the worst, after about two hours of skating, both bushings were crushed and stuck in one direction. He's been skating for almost 13 years. Hope this helps!
It is a mini-cruiser, which is known for its strength as well as its ability to offer real value for the money you spent. This skateboard can also be expected to deliver an impressive performance – thanks to the Abec 7 skatro bearings used in it. There are also 59-mm urethane wheels and the 3-inch GOLD aluminum trucks that can help smoothen each ride.
The Moose Blank Skateboard deck is a made with a 7-ply composition and features Canadian Maple wood. The board is 8.25 inches in length, but Moose Blank offers shorter boards as well, fitting men and women of just about any size and skill. The deck itself has a modern concave, making turning a breeze for beginners and pros. The nose and tail are particularly steep for tricks - “perfect for shredding,” says Blank Moose. Although this board is 100 percent blank, Moose Blank offers stains and dips for monochromic board designs as well. There are also Moose Blank sets for sale, which provide a set of blank decks at a discount.
Popsicle - A Popsicle complete skateboard is typically between 30 and 34 inches in total length with a varying width between 6.0 inches wide and 9.25 inches wide. You can check out the deck size chart to pick the complete that will be best suitable for you. These decks all come with grip tape and are a more technical skateboard for tricks and for the skatepark. If you want to do more than cruise the streets, a Popsicle is what you are looking for. All of our complete skateboards include the deck, trucks, wheels, grip, bearings and hardware. They are all also fully assembled. When choosing a complete, typically the more expensive completes will include a higher quality deck, better and longer lasting trucks, upgraded wheels and a higher abec rating on the bearings.
Almost every skate shop will have a wall of boards that is either organized by brand, size, or alphabetically. At our CCS skate shop, we have multiple walls of boards that we try and keep ordered alphabetically. A wall of skateboards, at first glance, can be overwhelming, but if you know what size and roughly what brands you like, it should be fairly easy for you to figure out what board you want. Now would be a good time to mention our CCS Skateboard Buyer’s Guide, specifically the Decks Guide. In the CCS Decks Guide, you’ll find all the information you need to gain a basic understanding of skateboard decks.
Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
After you’ve properly applied a burst of force to the tail, the top-side of your front foot’s toe should start dragging up your board almost automatically. Eventually, the higher you are able to bring your front foot during lift will determine the apex of your ollie, so work gradually towards lifting your front foot as high as your body allows. Skateboarders who record the highest ollies usually (somehow manage to!) bring their feet higher than their hips!
New shoes + new board + new grip tape isn’t going to help anything you need to reed what is above bro its an easy how to….bend down push your back foot down make sure the tail snaps off the ground and slid your front foot forward in one swift motion you’ll get it…iv been skating 11 years and its taken me this long to finally land kick flips regularly heel flips and varials my tres are 1 outa 10 still so I practice every day and someday ill be able to land it regularly when I want skateboarding takes alot of patients ALOT so dont think you’re going to learn everything over night just sayin
This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!