Pull your knees up into your chest – How far you actually want to pull your legs up is totally up to you, but the higher your feet go, the higher your board will go too. By the way, the highest recorded preferred stance ollie-pop is 45 inches, done by Aldrin Garcia, and the highest switch stance ollie-pop is 40.125 inches, by Gavin Caperton. And if you’re going for endurance rather than height, the record for most consecutive hops is held by Rob Dyrdek, who did 215 of them in a row on his TV show Rob and Big. So those give you something to shoot for.
In 1978, Alan Gelfand, who was given his nickname "Ollie" by Scott Goodman, learned to perform no-handed aerials in bowls and pools using a gentle raising of the nose and scooping motion to keep the board with the feet. There are numerous references to Alan Gelfand's Ollie with most notably pictures in the 1970s skateboarding magazine "Skateboarder".
Choosing a skateboard deck can be approached in a few different ways: you can choose your board based off the graphic, the brand, the shape, the width, or even the color. For most skateboarders, it’s a combination of all these factors, but if you’ve never skateboarded before, you may not know what shape, width, or brand you like best. In this case, choosing your favorite graphic would make total sense.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
Mini Cruisers have exploded in popularity in recent years. These short and skinny boards are may not have the versatility of a standard skateboard, allowing for a full range of tricks and travel. However, these compact boards are ideal for urban and college living where space for storage and riding are both minimal. If you want to ride a mini-cruiser, but you hate the plastic decks or you want to build your own, check out the Bamboo Skateboard mini cruiser deck.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!
Sizing plays an important role in the performance of any deck. A large majority range in size from 7.75" to 8.5" in width. These will provide a great platform for shredding any obstacle and will excel in street and skatepark environments alike. For those who prefer a smaller board, decks are offered down to 7.5" in width- benefiting people with smaller feet or the technical skater. Conversely, those looking for a wider board will enjoy our selection ranging up to 8.9" wide. Larger decks will accommodate those with very large feet, as well as offer an amazing experience for cruising and shredding large ramps and transitions.
Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.
A skateboard consists of a deck, trucks, wheels, bearings, hardware, and griptape. All parts come in a variety of sizes, graphics, colors, and signature pro series. The deck is the essential part of any skateboard. The deck ranges generally from 7.5" to 8.5". Skaters choose their board size for many reasons, but the basic deciding factor comes down to style of skating and foot size. Transition skaters usually ride a wider deck, while street skaters tend to go with a smaller deck. Skate brands such as Girl, enjoi, and Welcome offer a wide range of boards in regards to sizes and graphics. Skateboard trucks come in either a high or low setting, and also in a range of widths. The main factors in a truck, are how well they turn, and how well they grind. Independent, Venture, and Thunder, are truck brands that are well known for their turning and grinding capabilities. The skate hardware is generally either Phillips head or Allen key bolts. The skateboard wheels range from 50mm to 60mm. Some brands offer smaller and larger sizes, but 50-60mm is the general range. Like the deck sizes, wheel sizes depend on the skater's choice of terrain: Transition skaters tend to ride bigger wheels, while street skaters usually go with smaller wheels. Bones, Spitfire, Ricta, and Wayward wheel companies all make wheels for any terrain, whether you're a street shredder or a park burner. Skate bearings follow the ABEC rating system, which includes grades 1, 3, 5, 7, and 9. Bones, Bronson, and Andale are some of the top bearing brands in the skate market. CCS proudly carries all these brands, and many more.
In 1977, skate parks began cropping up all over the place, including Skateboard USA, where Gelfand began to spend most of his time. His buddy, Scott Goodman, is the one who gave Gelfand the nickname of “Ollie” and dubbed his aerial lipside the “ollie-pop.” Pictures of Gelfand during this time period clearly show him getting airborne and performing the trick associated with his name today.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
The Krown Rookie Skateboard Complete 7.5 comes with thick, sturdy 7-ply maple wood deck. It gives you more control and permits you to perform various tricks. It features carbon steel ABEC-3 bearings, aluminum trucks, bushings and 54mm x 34mm wheels. This board is perfect for kids who are 8 years and older. It has a maximum weight capacity of up to 220 lbs.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them . Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
Pop the board in the air – The reason you jump up into the air in the first place is because you’re slamming the back end into the ground (don’t worry, your board is made to take the abuse). It’s the same motion you would do if you were standing near the board and wanted to pop the board up into your hands, except this time, you’re standing on top of it. As soon as you feel the board pop into the ground, kick your front foot up into the air at the same time. The timing on this is important: kick too early and you won’t go anywhere, kick too late and your board will fly out from underneath you.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
With Board Blazers LED Cheap Skateboards, you can quickly customize your ride. There’s no need for any bulky battery pack or wires. You just need to place the lights under the trucks to do the tricks. Now, you can cruise safely with style. It is self-adhesive and every light comes with small, long-lasting, and easily replaceable lithium batteries. The on/off activation is controlled manually. It includes a set of 4 lights with the matching color. It is best for all types skateboards, longboards, and scooters. It is the perfect gift for anyone. It is the most trusted product with a rating of 4.5 on Amazon.
I found that my problem was unclear instruction about the timing between jumping and popping. One day when I was watching a slowmo ollie video though, I noticed that the skateboarder already was beginning to jump (at least his body was already going in an upward motion) before snapping the board off the ground. That was a critical change I needed to make in order to get it working. I had been trying to pop the board while all my weight was still pushing down on it (kind of an obvious mistake, but I somehow overlooked this). Hope this helps somebody.
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.
Velocity Boards Retro Skateboards is a complete 22″ Banana Skateboard. It includes 6″ Lightweight Aluminum Trucks, High-Speed ABEC-7 Bearings, High-Quality Wheels & Bushings and Hardware. It has a Unique Textured Waffle Pattern on Deck and is designed for Maximum Grip. The Deck measures about 22 x 6 x 4″. It has a 6″ Truck Axle and a 3″ Truck Hanger. It has a maximum weight capacity of 176 lbs. (80 kgs.). It is great for all skaters who are 6 years old and above. It has an Amazon rating of 4.7.
Here we have an original Z Jimmy Plumer model. It has some handling scuffing from being around for several decades, but displays great. Grip has no holes at trucks which leads me to believe it’s never had any mounted. This is one heavy fiberglass mamma jamma. Get this piece of history at a fair price. I will throw in free priority insured shipping for the con us. Everywhere else at actual cost. Thanks for looking.
This is how I learned how to ollie. Place your skateboard next to a curb, right up against it. This will help keep your board from rolling. Next, do everything that I just described, but don’t worry about what your board does. Just do it, and land up on top of the curb, on the sidewalk. Don’t stress about whether the skateboard will be there, or if you will get hurt – just go through the motions of ollying up the curb. If you do it right, the skateboard will be there. If you do it wrong, you’ll probably just land on your feet on the sidewalk. Here’s the key – just do it and expect it to work. Your body understands what you are trying to do, and the less you stress, the more it can kick in and fill in the blanks.