Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.
So you want to know how to ollie? Be warned, it’s not for the faint of heart, and a lot of people have tried and failed and tried some more and still failed and then eventually thrown their boards into a wall out of frustration (I have no idea who those people are). It’s by no means an easy skateboard trick, but if you want to know how to ollie, start with these simple tips:
Hey, I’m a girl too and I’ve been skateboarding for nearly ten years now. I’m not a pro or anything, but I used to ride around in the local skatepark that was mainly just a big bowl that was fun to just drop into and cruise around in. I’m only just now learning street tricks. Anyways, I’d go there and the dudes would sometimes tease me, but sometimes they’d tease me about it. The thing you gotta do is not give up. Just ignore them. Dudes are stupid. Practice at home, by yourself, and learn some awesome stuff. So when you get really good, you can go to the park and if they start saying bad stuff, show off. It’ll blow them away. It always made me feel really good to show them that I was better than them right after they teased me for it.
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
Skateboarding, in one form or another, has been around since the late 1950’s when the first brave pioneer first attached roller skate wheels to a piece of wood. As skateboarding progressed to mimic surfing, skateboards evolved with the style of riding. Skateboards grew and changed shapes as riders experimented with everything from plastic to fiberglass to aluminum constructions - all in an effort to push what was possible. Like most sports or art forms, progression is at the heart of skateboard innovation.
go with friends like most do, or at least with friends that support what your doing. Im 26 yrs old,I am a solo skater in elk city Oklahoma and the skate community is small, but we have a park , but in the smaller community skaters clique up I didn’t grow up here so I’m left out. I learn a I can online and practice little bit s out of the day when I have time from both jobs I work, I just don’t get a lot of beef cause I ignore them and do my own thing , but I’ve noticed my tricks that I land alone fairly easy they get difficult in the presence of others for some reason Being standoffish and skate with a lil aggression you’ll be alright, just don’t give up man at all costs do not give up.
The type of skating the rider wants to do will inform the board choice, which sometimes involves skating a non-popsicle shaped board. But if you are just starting out, you can simply start with the traditional popsicle shaped deck that you probably recognize. As you skate more and get to know what shapes you like or what kind of skateboarding you enjoy best, your decisions will take into account for company, shape, width, and style of riding. Until then, choosing a board by its graphic is totally acceptable. For an overview on types of skateboard decks and riding styles, check out our Skateboard Decks Section in our Buyer’s Guide. Once you find a deck you like, you can simply select the default wheels, trucks, bearings and grip tape or you have the option to make it a complete.
My son seems to have a lot of fun riding this skateboard. He will be out there doing tricks for hours. One evening when he took a break, I decided to see if I could still ride. When I took off down the driveway, I could feel how smoothly the wheels rolled. I used to have to pay extra for wheels like this when I was his age. Lost in thought, I coasted faster, and my neighbour didn't see me when I shot out of the driveway. Even though this thing flew several feet in the air, bounced, and came to rest more than 20 feet away, it had no visible damage! Not so for me. I loved the skateboard, but am now recovering from two broken ribs, torn neck cartilage, and a cracked pelvis. Still, this board rides like a dream!
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them . Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.
Shock pads are made of polyurethane and rubber. They are very similar to risers but vary in the fact that their sole purpose is to cushion the board from the trucks. Since the trucks are metal and the board wood, whenever the board hits the ground after doing a trick, the energy goes through the truck to the board ─ this has caused boards to crack, split, or even break in half, and shock pads were created to prevent this.
Made with bamboo and fiberglass, this board is tough, flexible and ready for anything. The construction is designed to feel and act like a snowboard. The drop-through design is perfect for freestyle longboarding, commuting, carving, pumping and more. It gives you better stability and more wheel clearance. The board is definitely best designed for carving but tricks and kicks are easily done as well.
Any serious skateboarder will tell you that the ollie is the most fundamental skateboard trick. In fact, it's probably the first trick that you'll learn on your skateboard. They’re great for getting over obstacles, moving around on your board, or just looking cool. Know the right way to move your feet on the board and with a little bit of practice, you can learn to pull off the perfect ollie.
Finally, just roll away. If this sounds simple, then great – get out there and practice! If this sounds too complicated, don’t worry. Just go slow, and take your time. There is no time limit to learn how to ollie – some people learn in a day, and I know one guy that took over a year to learn how to ollie on his skateboard. Also, like with most things in skateboarding, your body is learning how to ollie more than your mind is. So, with practice, you’ll eventually get it.
I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
In general an axle width should be chosen that is close to the width of the deck it will be used with. For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
The wheels are also impressive. Unlike some other skateboards that have wheels that are quite stiff, causing them to feel like they will lock up when you ride on them, the wheels in this complete skateboard for beginners are smooth and comfortable. These are also easily controllable, so rest assured that they offer a smooth and friction-free glide.