Popsicle - A Popsicle complete skateboard is typically between 30 and 34 inches in total length with a varying width between 6.0 inches wide and 9.25 inches wide. You can check out the deck size chart to pick the complete that will be best suitable for you. These decks all come with grip tape and are a more technical skateboard for tricks and for the skatepark. If you want to do more than cruise the streets, a Popsicle is what you are looking for. All of our complete skateboards include the deck, trucks, wheels, grip, bearings and hardware. They are all also fully assembled. When choosing a complete, typically the more expensive completes will include a higher quality deck, better and longer lasting trucks, upgraded wheels and a higher abec rating on the bearings.
Pop in your earbuds and head to the skate park with a skateboard that rolls through impressive stunts with ease. Most skateboards for sale offer strong wood decks that create a stable feel beneath your feet as you work on your grind and backslide techniques, but models with polypropylene construction offer a lightweight alternative with plenty of toughness. Try a surfboard-inspired design to cruise the streets like you'd ride a wave, or select a drop-through deck for smooth cruising. Grip tape promotes sure footing that helps you ride with confidence, but always put safety first - wear a skate helmet and skate pads from our Skateboard Shop for protection against mid-move falls.
If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.

To summarize, a skateboarder's feet need to do two things successfully to complete an ollie. They need to provide a changing force to move the board correctly (so that the combined force of gravity and the skater's feet add up to the green arrows above), and they need to provide different amounts of force with each foot (shown by the red and blue arrows above) to steer and turn the board into the right orientation.
Almost is proud to announce a collaboration with Skateistan, the award-winning non-profit organization empowering children and youth through skateboarding and education. They recently launched a new Skate School in Phnom Penh, Cambodia on Friday (February 23rd, 2018). Over 100 children celebrated alongside special guests from around the world, including Almost flow skater Sky Brown. 
With Enkeeo 22 Inch Cruiser Skateboards, you can cruise in style.  It has a dimension of 22 x 6 inches.  It comes with 3″ Black Coated Habitat trucks, Black 60mm Smooth wheels, and Abec11 bearings. It’s ready to ride and you can even personalize the tail of the board for free with a limitation of 10 Characters only. It has 30 days warranty and is manufactured in California.  It has a perfect 5 rating on Amazon.
In this modern era, manufacturers are incorporating hi-tech processes and top-shelf materials into the construction of the skateboard. Companies such as Almost have several versions of hi-tech decks such as the Impact, Double Impact, and Uber Light Series. Element makes Highlight decks with inlayed fiberglass beams, and Foundation has its signature Fiberprime decks. Other manufactures such as Flip, Habitat, Plan B, Skate Mental, and Zero offer boards with high-end P2 Construction. Hi-tech decks differ from traditional 7-ply Maple in that they are inlayed with Carbon Fiber, Fiberglass, Poly Ply, or Kevlar to produce a stronger skateboard with more pop. For more options, head over to our stellar selection of Hi-Tech Decks! Although hi-tech decks have made a strong presence within the market, standard 7-ply Maple remain the gold standard. This is due to the solid feeling and pop afforded through layering 7 Maple wood veneers together. The large majority of skateboard decks offered are constructed of 7-ply Maple. Most board manufacturers offer both high-tech decks and standard 7-ply Maple. No matter what you desire, CCS offers a complete selection in multiple sizes, shapes, and construction types!
After you’ve properly applied a burst of force to the tail, the top-side of your front foot’s toe should start dragging up your board almost automatically. Eventually, the higher you are able to bring your front foot during lift will determine the apex of your ollie, so work gradually towards lifting your front foot as high as your body allows. Skateboarders who record the highest ollies usually (somehow manage to!) bring their feet higher than their hips!

In this modern era, manufacturers are incorporating hi-tech processes and top-shelf materials into the construction of the skateboard. Companies such as Almost have several versions of hi-tech decks such as the Impact, Double Impact, and Uber Light Series. Element makes Highlight decks with inlayed fiberglass beams, and Foundation has its signature Fiberprime decks. Other manufactures such as Flip, Habitat, Plan B, Skate Mental, and Zero offer boards with high-end P2 Construction. Hi-tech decks differ from traditional 7-ply Maple in that they are inlayed with Carbon Fiber, Fiberglass, Poly Ply, or Kevlar to produce a stronger skateboard with more pop. For more options, head over to our stellar selection of Hi-Tech Decks! Although hi-tech decks have made a strong presence within the market, standard 7-ply Maple remain the gold standard. This is due to the solid feeling and pop afforded through layering 7 Maple wood veneers together. The large majority of skateboard decks offered are constructed of 7-ply Maple. Most board manufacturers offer both high-tech decks and standard 7-ply Maple. No matter what you desire, CCS offers a complete selection in multiple sizes, shapes, and construction types!


Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
Level out on the way down – Before you start to head back towards the safety of the earth, level your feet out as the board begins to fall. If you’re trying to jump a gap on your board, this will help you keep going straight and maintain your momentum. Alternatively, you can land on your nose or tail and perform a manual out of the jump, but those are pretty advanced moves. Might want to wait until those little pink training wheels are off your board first.
Before we show you how to ollie, let’s get familiar with the legends that brought this skateboard trick to the masses.  If it were a person, the history of ollie would start way back in 1974, when Alan Gelfand got his first skateboard from his father after his family moved to Hollywood, Florida from New York state. It didn’t take him too long to get the hang of it; he won the South Florida Skateboard championships two years later.
In the case that you didn't gave up after a hundred over tries, you'll start to develop a reaction to landing it. After a few hundred more tries, you'll feel you are getting off the ground and getting little air. And once you reach the thousandth try, you'll already be doing it whilst rolling and the next thousandth tries will be spent on clearing small cracks n obstacles and working towards ollieng up bigger obstacles n up ledges.
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve

The most common shape in skateboarding is called a popsicle shape. It has a curved tail and nose and features concave, which gives the board it’s shape. New skateboarders looking to learn how to carve, push, ollie, kickflip, and grind boxes, ledges, and rails should start with a popsicle shape. If you’re interested in knowing, we explain selecting a board by width, riding style, and board shape in the skateboard decks section of the buyer’s guide.


Krown burst on to the skate scene back in 1996 with the idea to provide a high quality skateboard to the rider on a budget. Krown recognized a big gap between the $20 big box retail skateboard and the $150 professional grade skateboard. The boards at big box retail stores have plastic wheels and don’t even roll! Krown’s idea to bring a price-point skateboard to the market that actually functions as a skateboard has proven to be successful after more than 20 years. With more than 20 years of industry knowledge and knowhow, Krown is able to source the best parts at the best prices, which allows Krown to pass the savings on to the consumer. This expertise has allowed Krown to venture into the world of skateboards, longboards, helmets, pads, and even tools. Krown is the best place to start for beginner and intermediate riders!
The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.
Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.

The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
Today, many riders use the “ollie-pop” on more than just the flat-level surfaces in between other tricks, it’s used heavily in the half-pipe and bowl ramps to allow the rider to go even higher in the air. Performing the “ollie-pop” while you’re at or near the top of the lip is a great way to get an extra couple feet, which might be all you need to get that extra turn in and nail the 720 (or 900, if you’re Tony Hawk).
Skateboarding started in California in the 1950s.[2] The first skateboards were made from roller skates (attached to a board).[3] Skateboarding gained in popularity because of surfing; in fact, skateboarding was initially referred to as "sidewalk surfing". Initially, skateboards were handmade from wooden boxes and planks by individuals. As the sport became more popular, companies started manufacturing skateboards. Boards are also continuing to evolve as companies try to make them lighter and stronger or improve their performance.
The grip tape found on a skateboard can actually be defined as the grainy sheet, which resembles sandpaper that also comes with a sticky underside. Such underside needs to adhere to the deck’s surfaces as a means of increasing traction or grip. No matter what skating style you use, the grip tape is extremely helpful in your attempt to stay on the board.

No I don’t believe that. You have to feel your board with your toes and feel the shape that the board Under the bottom of your feet and then master the pop with this newly formed connection. Faster faster and more guts are needed. When you are going as fast as you can go and can Ollie perfectly with complete consistency you’ll Ollie everywhere even in the cold cold winter.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
The Wasatch Imports Good Skateboards is the ultimate compact and complete street board that is ready-to-go. It is great for exercise and fun. It is very portable and perfect for all skill levels. It has a variety of awesome vintage color combinations that you can choose from. It is made of topline construction, with a high-density plastic deck, 59mm super smooth wheels, ABEC7 bearings, and solid aluminum trucks. It measures 22″ long and 6″ wide and weighs 4 pounds. It has a  full manufacturer’s lifetime warranty on all parts, pieces, and materials. It has a weight limit of 200 pounds which can ensure that bigger skaters can join the fun.

Made with bamboo and fiberglass, this board is tough, flexible and ready for anything. The construction is designed to feel and act like a snowboard. The drop-through design is perfect for freestyle longboarding, commuting, carving, pumping and more. It gives you better stability and more wheel clearance. The board is definitely best designed for carving but tricks and kicks are easily done as well.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air.[2] While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.[citation needed]

In the case that you didn't gave up after a hundred over tries, you'll start to develop a reaction to landing it. After a few hundred more tries, you'll feel you are getting off the ground and getting little air. And once you reach the thousandth try, you'll already be doing it whilst rolling and the next thousandth tries will be spent on clearing small cracks n obstacles and working towards ollieng up bigger obstacles n up ledges.
Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?
You have all the time in the world to skate, but you don't have the time to build a skateboard yourself. Maybe it's just easier to get a complete skateboard than spend hours in the garage trying to screw on new trucks. Even though customization is awesome, it's not necessary. You just want the freedom of the ride. When you get your skateboard, you just want to be able to get out and ollie off the curb as fast as possible. Which is why Tillys has an awesome selection of complete skateboards for you. Choose from some of your favorite skateboard brands including Primitive and Element and more. The bottom graphics are probably the most important part, so you can definitely choose the one that best fits your style. Get your new complete skateboard right here.
The board also boasts of its reasonably small size and lightweight nature, making it easy to control and ride. In addition, carrying it wherever you want to go is also much easier because of its lightness. It is flexible enough that it can accommodate the needs of different kinds of users, including cruisers, travelers, beginners, expert riders, and kids.
The grip tape found on a skateboard can actually be defined as the grainy sheet, which resembles sandpaper that also comes with a sticky underside. Such underside needs to adhere to the deck’s surfaces as a means of increasing traction or grip. No matter what skating style you use, the grip tape is extremely helpful in your attempt to stay on the board.
There are other types of ollies that you can do either alongside or combine with the ones listed above, like the tailgrab, indy grab, melon grab, stalefish, tweak, and dolphin nose. All of those skateboard tricks are performed more or less how they sound, but you might want to watch some videos on youtube to see a pro in action (as well as awesome cat videos).
Pop the board in the air – The reason you jump up into the air in the first place is because you’re slamming the back end into the ground (don’t worry, your board is made to take the abuse). It’s the same motion you would do if you were standing near the board and wanted to pop the board up into your hands, except this time, you’re standing on top of it. As soon as you feel the board pop into the ground, kick your front foot up into the air at the same time. The timing on this is important: kick too early and you won’t go anywhere, kick too late and your board will fly out from underneath you.
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
The Rimable Complete 22″ Skateboard is the most compact street board that are ready-to-use.  It is best for exercise and fun, and very portable.  There are five colors that you can choose from Black, Blue, White, Purple, and Green.  It has high-quality construction, with a high-density plastic deck.  It features extremely smooth 59mm wheels along with ABEC7 bearings and solid aluminum trucks.  It measures 22″ long and 6″ wide and weighs 4 pounds.  It has the best rating of 4.3 on Amazon.
James Haden is one of the owners of the Skateboarder community, together with Nash Gibson – his co-owner. He works as a full-time copywriter for a private company and also a true adventurer. He is an avid reader, writer, traveler, and extreme sports junkie. During his free time, he researches interesting content for their blog and continuously writes for their audience.
In this modern era, manufacturers are incorporating hi-tech processes and top-shelf materials into the construction of the skateboard. Companies such as Almost have several versions of hi-tech decks such as the Impact, Double Impact, and Uber Light Series. Element makes Highlight decks with inlayed fiberglass beams, and Foundation has its signature Fiberprime decks. Other manufactures such as Flip, Habitat, Plan B, Skate Mental, and Zero offer boards with high-end P2 Construction. Hi-tech decks differ from traditional 7-ply Maple in that they are inlayed with Carbon Fiber, Fiberglass, Poly Ply, or Kevlar to produce a stronger skateboard with more pop. For more options, head over to our stellar selection of Hi-Tech Decks! Although hi-tech decks have made a strong presence within the market, standard 7-ply Maple remain the gold standard. This is due to the solid feeling and pop afforded through layering 7 Maple wood veneers together. The large majority of skateboard decks offered are constructed of 7-ply Maple. Most board manufacturers offer both high-tech decks and standard 7-ply Maple. No matter what you desire, CCS offers a complete selection in multiple sizes, shapes, and construction types!
This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
×