An Ollie is basically an upward/forward jumping trick. The name “ollie” comes from the nickname of Alan Gelfand who created the ollie in 1976. The ollie was then modified for flat-ground use by Rodney Mullen in 1982, and it is this flat-ground version of the ollie which is most commonly referred to as the ‘ollie’ today. The ollie is arguably the most important trick in skateboarding because it is the foundation of the majority of skateboard tricks which require lift. When you want to do a trick like the kickflip, when you want to get onto something like a ledge, or down something like a set of stairs, or try handrails, the ability to ollie is a necessity. Therefore the ability to ollie high and with good control is critical to your total skateboarding skill-set.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.
The Skatro Mini Cruiser Skateboard includes Abec 7 Skatro Bearings, 59MM Urethane Skatro wheels, and 3-inch lightweight aluminum trucks.  The Skatro Flexy Technology ensures optimal flex on every board. Skatro outperforms most of the leading brands and it has an amazing value.  You can take this board on the subway, plane, train, and even on the bus.  It includes a color matching T-tool.  It has the best rating of 4.8 on Amazon.
I just can get any height on my ollie at all! so frustrating!, i can pop the board nicely and get it off the ground like that, but then i try to slide my foot up the board and it just stays at that 45 degree angle from when i popped it, i just can’t seem to slide and get it horizontal in the air, or any height for that matter, i have watched countless ollie tips and tricks videos, and practised for hours on end, the same ollie, i can ride smoothly and fine, along the side-walk for example but i just cant get any grip to bring my board up and forward (i bought a new skateboard yesterday, and also new shoes) so its obviously me which is incompetent in completing this ollie! I know im kind of waffling on a bit, but i just can get the board to get any height! Please help if you can!
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
It wouldn’t be until the early 1980’s however, that a man named Rodney Mullen fully developed the skateboard ollie and brought it into vogue. Competing in the Rusty Harris contest in Whittier, California in 1982, Rodney Mullen used a back and forth motion on his skateboard to strike the back end of the board on the ground and using the front end to level the board out in mid-air – all from a flat surface. The audience’s jaws collectively hit the ground.

500AlmostAluminatiArborBambooBirdhouseBlindBonzingCometCreatureDarkstarDB LongboardsDevilleDogtownDusters CaliforniaElementEnjoiEverseshFlipFocusFoundationGlobeGoldCoastGravityHabitatJartKebbekKrookedLandyachtzLaybackLushMadridMakahaMoonshine MFGOmenPennyPlan BPowell PeraltaPrism SkatePunkedRayneRealRememberRivieraRoad RiderSan ClementeSanta CruzSector 9Suicidal SkatesToy MachineWarehouseZ-FlexZero


I have skated for about 7 years i took a 2 year break. I have had about 50 boards and from that id say this board is ok seeing as iv had zero's break day one. if your newer to skateboarding and you dont mind the cost i would say go for it. For more hardcore skaters there are some things you should know about this board. im not 100% about the trucks day one just doing kickflips 360 flips smaller gaps.. its a bit shaky i dont think these trucks are make for stairs or big gaps but they will do till i have the cash for some thunders. the bearings are hit or miss one is on its way to being blow out the others seem to be fine. I got to say i really like the wheels there was not much info on them but they are smaller and harder and i love harder wheels i hit a nice nolie 360 first try and the sound of the slide took me back to the good days. As for the board i cant judge it off one day of skating but from the looks of it its not a knock off. Here are some tips for buying a board online. find real skaters in the comments dont buy a board because a dad said his kid loves it. When you get the board go over all the parts and look over your board well make sure there are no defects in the board. make sure the board is not waterlogged a few taps should tell you. if you dont know anything about skateboards ask a friend to help and if you find any defects send it back right away. I hope the review helps you.
New shoes + new board + new grip tape isn’t going to help anything you need to reed what is above bro its an easy how to….bend down push your back foot down make sure the tail snaps off the ground and slid your front foot forward in one swift motion you’ll get it…iv been skating 11 years and its taken me this long to finally land kick flips regularly heel flips and varials my tres are 1 outa 10 still so I practice every day and someday ill be able to land it regularly when I want skateboarding takes alot of patients ALOT so dont think you’re going to learn everything over night just sayin
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
It looks simple but yet complicated and vice versa. It takes most weeks to months to learn n some even years but a lifetime of effort to be consistent and be perfect at it and able to go higher, faster and further. It is not a feat you achieve once and it can be thrown out of the window if you want to continue to skate well. I've know skateboarders who just does ollies, boned ollies, ollie north and ollie souths, fakie ollies, switch ollies and nollies and nothing else but everytime he's popping them over 3ft height and up ledges, over gaps and down stair sets or over handrails. So no one's gonna argue on that even though he's not bustin some new fangled pressure flip late flip revert or something. He gets mad street creds for those huge ollies.
It looks simple but yet complicated and vice versa. It takes most weeks to months to learn n some even years but a lifetime of effort to be consistent and be perfect at it and able to go higher, faster and further. It is not a feat you achieve once and it can be thrown out of the window if you want to continue to skate well. I've know skateboarders who just does ollies, boned ollies, ollie north and ollie souths, fakie ollies, switch ollies and nollies and nothing else but everytime he's popping them over 3ft height and up ledges, over gaps and down stair sets or over handrails. So no one's gonna argue on that even though he's not bustin some new fangled pressure flip late flip revert or something. He gets mad street creds for those huge ollies.

A skateboard deck is made up of curved layers of wood that are combined with glue. Then, the skateboard deck is trimmed down to a board shape that is practical. Trucks are typically made of aluminum or other metal alloys. They are made by melted metal formed by a mold and later drilled into the skateboard deck. The wheels are formed the same way, but with polyurethane. They are attached by ball bearings to complete the product.
The wheels are also impressive. Unlike some other skateboards that have wheels that are quite stiff, causing them to feel like they will lock up when you ride on them, the wheels in this complete skateboard for beginners are smooth and comfortable. These are also easily controllable, so rest assured that they offer a smooth and friction-free glide.
Learn how to ollie off of a ramp: Ramps are a LOT of fun to ollie off of, but they are also a great way to break something if you don't know what you're doing! I have a cousin who almost lost his arm because of how nastily he broke it while ollying off a ramp. But don't let that scare you - if you know what you're doing, ollying off ramps is great!
No one had ever seen anything quite like it before, but no one knew just how transformative that moment would become. It wasn’t just that you could simply pop up into the air, it’s that it gave the rider a whole other set of opportunities to do tricks, and you don’t even have to be dependent on a ramp! As time went by, people began to add other skateboard tricks while they were airborne.
Ridge Skateboards For Beginners are a UK Brand and have taken over Europe. Now it is available in the U.S.A. exclusively through Amazon. The Deck measures 27″ long x 7.5″ wide (69cm x 19cm). It features 4″ wide high-performance trucks with 87A super soft yellow bushings. It is made of high quality secret plastic formula. It has a rating of 4.8 on Amazon.
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.
Before learning it, do have your riding basics down. Meaning you are very comfortable riding it around and doing kickturns and not be pushing mongo. Best to learn it whilst stationary with your wheels on a crack so that you don't move and slip out so much. I don't recommend doing it on grass or carpet cos when you pop the tail, it's gonna be absorbed by the floor and when you start doing it on pavement, your muscles will memorize a different way of doing it. So nope, no easy way out i guess.
No I don’t believe that. You have to feel your board with your toes and feel the shape that the board Under the bottom of your feet and then master the pop with this newly formed connection. Faster faster and more guts are needed. When you are going as fast as you can go and can Ollie perfectly with complete consistency you’ll Ollie everywhere even in the cold cold winter.
Krown burst on to the skate scene back in 1996 with the idea to provide a high quality skateboard to the rider on a budget. Krown recognized a big gap between the $20 big box retail skateboard and the $150 professional grade skateboard. The boards at big box retail stores have plastic wheels and don’t even roll! Krown’s idea to bring a price-point skateboard to the market that actually functions as a skateboard has proven to be successful after more than 20 years. With more than 20 years of industry knowledge and knowhow, Krown is able to source the best parts at the best prices, which allows Krown to pass the savings on to the consumer. This expertise has allowed Krown to venture into the world of skateboards, longboards, helmets, pads, and even tools. Krown is the best place to start for beginner and intermediate riders!
Today, many riders use the “ollie-pop” on more than just the flat-level surfaces in between other tricks, it’s used heavily in the half-pipe and bowl ramps to allow the rider to go even higher in the air. Performing the “ollie-pop” while you’re at or near the top of the lip is a great way to get an extra couple feet, which might be all you need to get that extra turn in and nail the 720 (or 900, if you’re Tony Hawk).
The KPC Series Pro Skateboard measures 8.0” x 32”. This is a common width most often associated with pro skateboarders. Wider and stronger than the rookies, this model is the perfect size for someone who is better at skating and looking for an upgrade from the rookie models. The pro features a modern concave which allows for not only comfort, but more pop making it easier to learn tricks.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.

When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.


So the proper foot placement for the ollie is with the ball of your back foot horizontal on the tail of your skateboard.  And your front foot centered on your board right behind the front trucks.  You may find that moving your feet around in different positions are more comfortable.  This is fine,  everybody can learn how to skateboard their own way.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
The Powell Golden Dragon 2 Skateboard is an affordable and complete skateboard for the beginners and also for the advanced skaters.  It has high-rebound, hand-cast polyurethane wheels to give you a great roll and grip.  It measures 7.5 inches wide with a colorful screen-printed bottom.  It is made in China and has an average rating of 4.2 on Amazon.
Rails (or ribs), are narrow strips of plastic or metal that are attached under the deck lengthwise along the edges. They are used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Rails also provide a more consistent feel for slides, as the slide of a regular skateboard will suffer from the wear of the paint or varnish on the bottom of the board. Although rarely used anymore, they are useful for experienced skaters that are capable of grabs.
The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
With Board Blazers LED Cheap Skateboards, you can quickly customize your ride.  There’s no need for any bulky battery pack or wires.  You just need to place the lights under the trucks to do the tricks.  Now, you can cruise safely with style.  It is self-adhesive and every light comes with small, long-lasting, and easily replaceable lithium batteries.  The on/off activation is controlled manually. It includes a set of 4 lights with the matching color.  It is best for all types skateboards, longboards, and scooters. It is the perfect gift for anyone.  It is the most trusted product with a rating of 4.5 on Amazon.
Pull your knees up into your chest – How far you actually want to pull your legs up is totally up to you, but the higher your feet go, the higher your board will go too. By the way, the highest recorded preferred stance ollie-pop is 45 inches, done by Aldrin Garcia, and the highest switch stance ollie-pop is 40.125 inches, by Gavin Caperton. And if you’re going for endurance rather than height, the record for most consecutive hops is held by Rob Dyrdek, who did 215 of them in a row on his TV show Rob and Big. So those give you something to shoot for.
It wouldn’t be until the early 1980’s however, that a man named Rodney Mullen fully developed the skateboard ollie and brought it into vogue. Competing in the Rusty Harris contest in Whittier, California in 1982, Rodney Mullen used a back and forth motion on his skateboard to strike the back end of the board on the ground and using the front end to level the board out in mid-air – all from a flat surface. The audience’s jaws collectively hit the ground.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air.[2] While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.[citation needed]
×