So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
The skater can gain greater clearance from the ground by jumping higher, popping faster, sliding the front foot farther forwards (starting the jump with the front foot farther back), and pulling the legs higher into the chest to raise the feet higher. Skaters attempting record-setting ollies even contort the legs so that board and feet are not directly below them, allowing the board to rise at or just below the level of the pelvis.
If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
In fact, we can work out how you need to steer the skateboard. Tracker has a nice feature that we'll call 'force arrows'. These arrows show you how much force acts on an object at every instant, and in which direction the force acts. So for example, if you were to kick a ball into the air, while the ball was mid-flight, this arrow would always point down and be the same length, even though the ball is moving forward. That's because the only force acting on the ball is gravity, which pulls it straight down, and acts with a constant strength. (For those of you who've studied physics, these arrows denote the acceleration of the center of mass, which by Newton's second law is proportional to the net force acting on the skateboard.)
The board also boasts of its reasonably small size and lightweight nature, making it easy to control and ride. In addition, carrying it wherever you want to go is also much easier because of its lightness. It is flexible enough that it can accommodate the needs of different kinds of users, including cruisers, travelers, beginners, expert riders, and kids.
The laws for skateboarding helmets vary from state to state. Many states require that skaters wear a helmet under a certain age, and some states like California make all skaters under 18 wear a CPSC Certified helmet at all times. CSPC skateboard helmets usually have an EPS protective liner that meets the safety standards for skateboarding. Make sure you check your state's regulations before ordering.
So the proper foot placement for the ollie is with the ball of your back foot horizontal on the tail of your skateboard.  And your front foot centered on your board right behind the front trucks.  You may find that moving your feet around in different positions are more comfortable.  This is fine,  everybody can learn how to skateboard their own way.

Learn how to ollie off of a ramp: Ramps are a LOT of fun to ollie off of, but they are also a great way to break something if you don't know what you're doing! I have a cousin who almost lost his arm because of how nastily he broke it while ollying off a ramp. But don't let that scare you - if you know what you're doing, ollying off ramps is great!
When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.
There are actually several types of skateboards but the most common ones are the longboard, cruiser, and carve skateboards. A longboard is usually at least 33 inches. It is a great mode of transportation and works well for cruising around. The cruiser also works well as a mode of transportation but many consider it more beneficial as it has a shorter skateboard, which promotes ease in transporting around.
Grip tape is a sheet of paper or fabric with adhesive on one side and a surface similar to fine sandpaper on the other. Grip tape is applied to the top surface of a board to allow the rider's feet to grip the surface and help the skater stay on the board while doing tricks. Grip tape is usually black, but is also available in many different colors such as pink, red, yellow, checkered, camo, and even clear. Often, they have designs die-cut to show the color of the board, or to display the board's company logo. Grip tape accumulates dirt and other substances that will inhibit grip, so use of a grip eraser or rubber eraser is necessary after riding through mud or with dirty shoes.
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
Ride like the pros with Tony Hawk skateboards, Airwalk skateboards and boards from Razor�, Kryptonics, Maple� and other trusted brands. These high-quality skateboards utilize smooth-rolling trucks and ball bearings that prevent jams and freezing as you shoot through the half-pipe or roll down the sidewalk. And while performance is your top consideration, all your tricks and moves will look even cooler with a board that's splashed with bright colors, emblazoned with attention-getting graphics and made with a sleek design. Choose from styles with bold patterns and detailed, full-color artwork that showcase your personal aesthetic along with your athleticism.
After that I went to my regular Olley spot to practice, fell so hard three times. My legs were so fucked up from the day before. Now I feel like shit because I had problem with a 20cm ledge I landed at least 100 times up and down yesterday. I’m even capable of 50cm ledges at slow speed, but I only get the front wheel and the board up so I have to put pressure on the nose to get it all the way up.
It's a neat piece of science art, and it also tells us something interesting. The arrows show us that the force on the skateboard is constantly changing, both in magnitude as well as in direction. Now the force of gravity obviously isn't changing, so the reason that these force arrows are shrinking and growing and tumbling around is that the skater is changing how their feet pushes and pulls against the board. By applying a variable force that changes both in strength and direction, they're steering the board.
Playwheels Disney Skateboard For Kids is a 21″ Wood single kicktail deck with painted edges.  It has clear sand spray top grip with color graphic and full-color bottom graphics with a retro shape.  It features multi-colored composite truck and baseplate components with carbon steel axles.  This is great for kids who are starting to learn skating.  It has an average rating of 4.2 on Amazon.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.

It comes with a plastic board deck, which is small in size, making it ideal for riders who need a really sturdy skateboard. It is more suitable for both experts and beginners who want to learn new tricks in skateboarding. The fact that it is stable and small makes it good for kids, too. It promotes ease in riding and controlling it in a crowded street. This complete skateboard is lightweight, too, allowing you to carry it almost everywhere.

The Moose Blank Skateboard deck is a made with a 7-ply composition and features Canadian Maple wood. The board is 8.25 inches in length, but Moose Blank offers shorter boards as well, fitting men and women of just about any size and skill. The deck itself has a modern concave, making turning a breeze for beginners and pros. The nose and tail are particularly steep for tricks - “perfect for shredding,” says Blank Moose. Although this board is 100 percent blank, Moose Blank offers stains and dips for monochromic board designs as well. There are also Moose Blank sets for sale, which provide a set of blank decks at a discount.

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
The Skatro Mini Cruiser Skateboard includes Abec 7 Skatro Bearings, 59MM Urethane Skatro wheels, and 3-inch lightweight aluminum trucks.  The Skatro Flexy Technology ensures optimal flex on every board. Skatro outperforms most of the leading brands and it has an amazing value.  You can take this board on the subway, plane, train, and even on the bus.  It includes a color matching T-tool.  It has the best rating of 4.8 on Amazon.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
Velocity Boards Retro Skateboards is a complete 22″ Banana Skateboard.  It includes 6″ Lightweight Aluminum Trucks, High-Speed ABEC-7 Bearings, High-Quality Wheels & Bushings and Hardware.  It has a Unique Textured Waffle Pattern on Deck and is designed for Maximum Grip.  The Deck measures about 22 x 6 x 4″.  It has a 6″ Truck Axle and a 3″ Truck Hanger.  It has a maximum weight capacity of  176 lbs. (80 kgs.).  It is great for all skaters who are 6 years old and above.  It has an Amazon rating of 4.7.

In fact, we can work out how you need to steer the skateboard. Tracker has a nice feature that we'll call 'force arrows'. These arrows show you how much force acts on an object at every instant, and in which direction the force acts. So for example, if you were to kick a ball into the air, while the ball was mid-flight, this arrow would always point down and be the same length, even though the ball is moving forward. That's because the only force acting on the ball is gravity, which pulls it straight down, and acts with a constant strength. (For those of you who've studied physics, these arrows denote the acceleration of the center of mass, which by Newton's second law is proportional to the net force acting on the skateboard.)
This board includes professional assembly. All Krown skateboards arrived assembled and ready to ride straight out the box. The Rookie model includes heavy duty Aluminum 5.0 trucks, 52mm 99A high-rebound urethane wheels, precision speed Abec 7 bearings, high tensile phillips head mounting hardware, and 80 grit black grip tape. Each component meets the industry standards and are a common choice of skaters worldwide.
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
My problem is Everytime I try to pop the back it’s not hard enough and I get no air. The article says to jump up so I do it physically and sometimes it seems to help. But when I watch skate videos and other skaters It doesn’t appear they are actually jumping up. They just seem to be popping the board. So should I physically jump? May sound stupid but it’s something I struggle with.
Place your back foot on the edge of the tail (this is where you will apply a burst of force to the skateboard) and prepare to exert force through the foot’s ‘big-toe-mound’ area. Place your front foot behind the front bolts. Make sure the weight bearing down on your feet, as well as the weight of your body, is generally centered over the ‘middle line’ of your skateboard.
It is mainly because those items are guaranteed to help you familiarize yourself with the ins and outs of using them. They are a big help in making you feel comfortable when you push off with your feet while also balancing on top of the board when riding. It is not good to go for a very technical product, so it’s best to choose the mentioned types first.
×