Finally, just roll away. If this sounds simple, then great – get out there and practice! If this sounds too complicated, don’t worry. Just go slow, and take your time. There is no time limit to learn how to ollie – some people learn in a day, and I know one guy that took over a year to learn how to ollie on his skateboard. Also, like with most things in skateboarding, your body is learning how to ollie more than your mind is. So, with practice, you’ll eventually get it.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.

The Bamboo Skateboards Galaxy Series Cosmic Cloud Skateboard Deck is an excellent option. This concave board is made exclusively of a bamboo hybrid, rather than pure maple. This means the deck is lighter, stronger, more flexible and can even absorb shock better. The non-carbonized, light-wood deck is made of 6-ply wood and is in its fourth generation of designs.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
Don’t get your hopes shot if it takes you a while to get this down.  Once you know how to ollie, beginner skateboarders you can do any trick in the book with just a little bit of practice.  Once you get this trick down while your stationary, go practice while moving around a little bit, try to hop off a couple of curbs.   You’ll be skateboarding like a pro in no time.  Just keep at it.
I found that my problem was unclear instruction about the timing between jumping and popping. One day when I was watching a slowmo ollie video though, I noticed that the skateboarder already was beginning to jump (at least his body was already going in an upward motion) before snapping the board off the ground. That was a critical change I needed to make in order to get it working. I had been trying to pop the board while all my weight was still pushing down on it (kind of an obvious mistake, but I somehow overlooked this). Hope this helps somebody.
Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.
The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
A skateboard deck is made up of curved layers of wood that are combined with glue. Then, the skateboard deck is trimmed down to a board shape that is practical. Trucks are typically made of aluminum or other metal alloys. They are made by melted metal formed by a mold and later drilled into the skateboard deck. The wheels are formed the same way, but with polyurethane. They are attached by ball bearings to complete the product.
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve
×