The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
A skateboard deck is made up of curved layers of wood that are combined with glue. Then, the skateboard deck is trimmed down to a board shape that is practical. Trucks are typically made of aluminum or other metal alloys. They are made by melted metal formed by a mold and later drilled into the skateboard deck. The wheels are formed the same way, but with polyurethane. They are attached by ball bearings to complete the product.
I just can get any height on my ollie at all! so frustrating!, i can pop the board nicely and get it off the ground like that, but then i try to slide my foot up the board and it just stays at that 45 degree angle from when i popped it, i just can’t seem to slide and get it horizontal in the air, or any height for that matter, i have watched countless ollie tips and tricks videos, and practised for hours on end, the same ollie, i can ride smoothly and fine, along the side-walk for example but i just cant get any grip to bring my board up and forward (i bought a new skateboard yesterday, and also new shoes) so its obviously me which is incompetent in completing this ollie! I know im kind of waffling on a bit, but i just can get the board to get any height! Please help if you can!
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
If you love skateboarding, then it is a must for you to invest in a high-quality backpack or bag. It is an essential gear, especially if you are someone on the go. You need it as it lets you bring all the things and items you need while you are riding to work or school – that’s possible while still ensuring that you bring your board with you all the time.
This is how I learned how to ollie. Place your skateboard next to a curb, right up against it. This will help keep your board from rolling. Next, do everything that I just described, but don’t worry about what your board does. Just do it, and land up on top of the curb, on the sidewalk. Don’t stress about whether the skateboard will be there, or if you will get hurt – just go through the motions of ollying up the curb. If you do it right, the skateboard will be there. If you do it wrong, you’ll probably just land on your feet on the sidewalk. Here’s the key – just do it and expect it to work. Your body understands what you are trying to do, and the less you stress, the more it can kick in and fill in the blanks.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.