Bolted onto the underside of the tail end of a skateboard, the tail guard (also known as a "skid plate") protected the tail end from skid stops and other maneuvers that would otherwise wear away the wood (commonly known as razor tail) and decrease the longevity of the tail. Typically made of plastic, these were widely popular in the '80s but their usage quickly diminished with the arrival of two-tail board designs, which became increasingly popular in the '90s.
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve
The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
In fact, we can work out how you need to steer the skateboard. Tracker has a nice feature that we'll call 'force arrows'. These arrows show you how much force acts on an object at every instant, and in which direction the force acts. So for example, if you were to kick a ball into the air, while the ball was mid-flight, this arrow would always point down and be the same length, even though the ball is moving forward. That's because the only force acting on the ball is gravity, which pulls it straight down, and acts with a constant strength. (For those of you who've studied physics, these arrows denote the acceleration of the center of mass, which by Newton's second law is proportional to the net force acting on the skateboard.)
Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.
!function(e){function n(t){if(r[t])return r[t].exports;var i=r[t]={i:t,l:!1,exports:{}};return e[t].call(i.exports,i,i.exports,n),i.l=!0,i.exports}var t=window.webpackJsonp;window.webpackJsonp=function(n,r,o){for(var s,a,l=0,u=[];l1)for(var t=1;td)return!1;if(p>f)return!1;var e=window.require.hasModule("shared/browser")&&window.require("shared/browser");return!e||!e.opera}function a(){var e="";return window.Q.sendErrorsToWeblogger&&"quora.com"==window.Q.subdomainSuffix&&(e+=[window.location.protocol,"//log.quora.com"].join("")),e+="/ajax/log_errors_3RD_PARTY_POST"}function l(){var e=o(h);h=[],0!==e.length&&c(a(),{errors:JSON.stringify(e)})}var u=t("./third_party/tracekit.js"),c=t("./shared/basicrpc.js").rpc;u.remoteFetching=!1,u.collectWindowErrors=!0,u.report.subscribe(r);var f=10,d=window.Q&&window.Q.errorSamplingRate||1,h=[],p=0,m=i(l,1e3),w=window.console&&!(window.NODE_JS&&window.UNIT_TEST);n.report=function(e){try{w&&console.error(e.stack||e),u.report(e)}catch(e){}};var y=function(e,n,t){r({name:n,message:t,source:e,stack:u.computeStackTrace.ofCaller().stack||[]}),w&&console.error(t)};n.logJsError=y.bind(null,"js"),n.logMobileJsError=y.bind(null,"mobile_js")},"./shared/globals.js":function(e,n,t){var r=t("./shared/links.js");(window.Q=window.Q||{}).openUrl=function(e,n){var t=e.href;return r.linkClicked(t,n),window.open(t).opener=null,!1}},"./shared/links.js":function(e,n){var t=[];n.onLinkClick=function(e){t.push(e)},n.linkClicked=function(e,n){for(var r=0;r>>0;if("function"!=typeof e)throw new TypeError;for(arguments.length>1&&(t=n),r=0;r>>0,r=arguments.length>=2?arguments[1]:void 0,i=0;i>>0;if(0===i)return-1;var o=+n||0;if(Math.abs(o)===Infinity&&(o=0),o>=i)return-1;for(t=Math.max(o>=0?o:i-Math.abs(o),0);t>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=0;r>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=new Array(s),i=0;i>>0;if("function"!=typeof e)throw new TypeError;for(var r=[],i=arguments.length>=2?arguments[1]:void 0,o=0;o>>0,i=0;if(2==arguments.length)n=arguments[1];else{for(;i=r)throw new TypeError("Reduce of empty array with no initial value");n=t[i++]}for(;i>>0;if(0===i)return-1;for(n=i-1,arguments.length>1&&(n=Number(arguments[1]),n!=n?n=0:0!==n&&n!=1/0&&n!=-1/0&&(n=(n>0||-1)*Math.floor(Math.abs(n)))),t=n>=0?Math.min(n,i-1):i-Math.abs(n);t>=0;t--)if(t in r&&r[t]===e)return t;return-1};t(Array.prototype,"lastIndexOf",c)}if(!Array.prototype.includes){var f=function(e){"use strict";if(null==this)throw new TypeError("Array.prototype.includes called on null or undefined");var n=Object(this),t=parseInt(n.length,10)||0;if(0===t)return!1;var r,i=parseInt(arguments[1],10)||0;i>=0?r=i:(r=t+i)<0&&(r=0);for(var o;r
Bought as a Christmas gift for our nephew. He's not an expert or anything so I was looking for something that would work while he gets used to riding one. When I received it I pulled it out of the package to check it out and the construction was good. The wheels spun smoothly and the grip tape was nicely put on. I don't know how it would resist to some board slides but for a 15 year old just starting out its a good board.

This ollie is commonly referred to as an “Ollie Nosebone.” First of all, you need good ollie skills. The key for this ollie is your front foot. When you reach the peak, (gently!) push your front foot forward not moving any other part of your body. That’s it, simple yet difficult. Of utmost importance is practicing your regular ollie over and over in various conditions so that extension tricks such as the ‘nosebone’ come almost naturally with experimentation. Nevertheless, here is a movie explaining how to do it.
I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.

The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.

The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.
My fiancee purchased this via my account and he says that it has good concave shape and pop.Assembling was fairly simple, easier if you have a box cutter on hand to help with laying the grip tape. The deck was the best part but the bearings were good too. He thought the bushings were the worst, after about two hours of skating, both bushings were crushed and stuck in one direction. He's been skating for almost 13 years. Hope this helps!

The DAPANLA deck is 7.5-by-31-inches in size, on the smaller side of good quality, real skateboard decks, which makes it ideal for smaller and shorter people. Unlike many decks on the market today, the DAPANLA deck comes with non-slip grip tape on the top. The underside of the deck is similarly decorated, with a range of DAPANLA designs including the fun cartoon avocado board that is sure to turn a few heads for its uniqueness. 


When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!

Plan B sells boards with overall reliable attributes. They offer decks made from seven-ply wood. Powell is a longstanding company that founded the legendary Bones Brigade team, which kick-started Tony Hawk's career. Their skateboard designs change annually, but always look cool. Tony Hawk’s skate company is called Birdhouse. Their decks feature bird themes and have a thicker sixth layer of wood that makes it easier to jump and do flip tricks, which is ideal for vertical-style skateboarding. For environmentally-conscious skaters and fans of Bam Margera, buy a board from Element. They have variety on the technical side with their seven-ply boards and Helium decks. Their skateboards are made with an air pocket to be lightweight.

Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.[5]
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
Ridge Skateboards For Beginners are a UK Brand and have taken over Europe. Now it is available in the U.S.A. exclusively through Amazon. The Deck measures 27″ long x 7.5″ wide (69cm x 19cm). It features 4″ wide high-performance trucks with 87A super soft yellow bushings. It is made of high quality secret plastic formula. It has a rating of 4.8 on Amazon.

The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
The switch stance ollie uses a similar body motion, but the nollie is subtly distinct: For one, the rider is always moving forward, with the body positioned in a nollie stance--closer to the nose and with the front foot on the nose. Secondly the rider usually postures the body differently so as to compensate for this stance with respect to the forward motion. The rider presses the nose down using their front foot to engage the "pop" motion in order for the board to rise. This is In contrast to a "Fakie Ollie" where the pop motion is performed by the rear foot on the tail, similarly to a normal Ollie, however the rider is traveling backwards when performing a Fakie Ollie. Where in a Nollie the rider is traveling forward with their front foot on the nose to apply the initial force "pop".
After you’ve properly applied a burst of force to the tail, the top-side of your front foot’s toe should start dragging up your board almost automatically. Eventually, the higher you are able to bring your front foot during lift will determine the apex of your ollie, so work gradually towards lifting your front foot as high as your body allows. Skateboarders who record the highest ollies usually (somehow manage to!) bring their feet higher than their hips!
It comes with a plastic board deck, which is small in size, making it ideal for riders who need a really sturdy skateboard. It is more suitable for both experts and beginners who want to learn new tricks in skateboarding. The fact that it is stable and small makes it good for kids, too. It promotes ease in riding and controlling it in a crowded street. This complete skateboard is lightweight, too, allowing you to carry it almost everywhere.
Skateboarding is a very individual activity. There is no right or wrong way to skate. Skateboarding still hasn't stopped evolving, and skaters are coming up with new tricks all the time. Skateboarding has gone through its ups and downs over the years. However, since 2000, due to attention in the media and products like skateboarding video games, children's skateboards and commercialization, skateboarding has been pulled into the mainstream. As more interest and money has been invested into skateboarding, more skate parks, better skateboards have become available. In addition, the continuing interest has motivated skateboarding companies have to keep innovating and inventing new things. In 2020 Skateboarding will appear for the first-time in the Olympics in Tokyo, Japan.[4]
Slide your front foot as soon as you start jumping. Use the same movement you have been practicing to slide your foot towards the top end of the board, just as you jump off it and kick the back down. The front of your board should lift up as you slide your foot along it, with your foot hitting the top of the board at the highest point of your jump.[9]
×