Are you on a hunt for the best skateboard on the market today? Then you are in the right place as this comprehensive article is designed to give you information about skateboarding and types of skateboards in general. By learning about the different types of skateboards and what each one can do, figuring out what works for you the best is a lot easier.
Place your back foot on the edge of the tail (this is where you will apply a burst of force to the skateboard) and prepare to exert force through the foot’s ‘big-toe-mound’ area. Place your front foot behind the front bolts. Make sure the weight bearing down on your feet, as well as the weight of your body, is generally centered over the ‘middle line’ of your skateboard.
So the proper foot placement for the ollie is with the ball of your back foot horizontal on the tail of your skateboard.  And your front foot centered on your board right behind the front trucks.  You may find that moving your feet around in different positions are more comfortable.  This is fine,  everybody can learn how to skateboard their own way.
beginner skateboarder beginner skateboarders beginner skateboarder tips beginner skateboarding tricks common ollie mistakes get better at skateboarding get more pop how to kickflip how to ollie how to skateboard improve at skateboarding kickflip kickflip trick tip landing tricks consistently learn how to ollie learn how to skateboard ollie higher overcoming fear popping tricks higher pop shuvit pop tricks higher secrets of skateboarding skateboarding skateboarding chickenfoot skateboarding secrets skateboarding tips skateboarding tricks skateboarding trick tips skateboard tricks skateboard tricks for beginners skateboard trick tips skatepark skatepark tips style matters skateboarding tricks for beginners trick tips trips for beginner skateboarders
So you want to know how to ollie? Be warned, it’s not for the faint of heart, and a lot of people have tried and failed and tried some more and still failed and then eventually thrown their boards into a wall out of frustration (I have no idea who those people are). It’s by no means an easy skateboard trick, but if you want to know how to ollie, start with these simple tips:

But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Choosing a skateboard deck can be approached in a few different ways: you can choose your board based off the graphic, the brand, the shape, the width, or even the color. For most skateboarders, it’s a combination of all these factors, but if you’ve never skateboarded before, you may not know what shape, width, or brand you like best. In this case, choosing your favorite graphic would make total sense.
Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
×