The Bamboo Mini Cruiser deck is 6-inches-by-22.5-inches with that classic cruiser shape. The board is made with 6-ply bamboo and maple construction, which is lightweight, flexible and eco-friendly. Bamboo Skateboards claims this board has a turning radius not seen in most mini decks. The small, blank deck is heavy duty and durable in a way not all mini cruisers are. The non-carbonized board is ready for you to slap on the grip tape and artwork you want and then get riding.
A skateboard deck is made up of curved layers of wood that are combined with glue. Then, the skateboard deck is trimmed down to a board shape that is practical. Trucks are typically made of aluminum or other metal alloys. They are made by melted metal formed by a mold and later drilled into the skateboard deck. The wheels are formed the same way, but with polyurethane. They are attached by ball bearings to complete the product.
The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.
The Moose Blank Skateboard deck is a made with a 7-ply composition and features Canadian Maple wood. The board is 8.25 inches in length, but Moose Blank offers shorter boards as well, fitting men and women of just about any size and skill. The deck itself has a modern concave, making turning a breeze for beginners and pros. The nose and tail are particularly steep for tricks - “perfect for shredding,” says Blank Moose. Although this board is 100 percent blank, Moose Blank offers stains and dips for monochromic board designs as well. There are also Moose Blank sets for sale, which provide a set of blank decks at a discount.
Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
The DreadXBoards Concave Skateboard has Plastic Deck Injection Molded for excellent durability. It features Urethane Wheels 59mm 78a, aluminum trucks, and Abec 7 Bearings. It is completely assembled and is ready to ride. It is perfect for beginners or experienced riders. It can load up to 185 lbs. It is great for kids and adults. It has an excellent rating of 4 on Amazon.
Low ollies: This can happen for a lot of reasons, but the biggest one is that you are not crouching low enough before your ollie, and not pulling your feet high enough after you jump. When you crouch down, try and touch the ground. When you jump, try to hit yourself in the chest with your knees. Both knees. Don’t worry about falling. That will happen sometimes – that’s just part of skateboarding! For more help, read the How Can I Make My Ollies Higher? FAQ
Hey Isak I’m a 46 year old Street Skateboarder recently started Skateboarding a few months back I’m trying to get my Ollies down I’ve stopped Skating for the last couple of weeks because I was getting frustrated with not getting my Ollies I was in a funk confidence slightly knocked so I’m thinking of going Street Skating all day tomorrow and not caring about what others think it’s all in my mind I know I can do this but may mind says I’m going to slam I skate alone but shouldn’t make any difference I need help with motivation somebody give me a kick up the ass you are never to old to start Skateboarding help dudes?! Mark UK. 🙂
Crouch down – While you’re standing on the board with your feet in the right position, crouch down closer towards the board. Don’t turn into a hunchback here; keep your back as straight as possible and don’t stick your rear out too far off the board, otherwise you’ll mess the whole thing up. Stay on the balls of your feet too; if you’re more on your toes, you’ll actually move the board in air and land off of it, and no one wants that. If you need to readjust your feet before you jump, just do a little micro-jump to reposition your feet, or shuffle into position. The first way is easier and faster, the second is more awkward and can mess up your shoes.
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
Almost no one lands an ollie on their first try. Repetition is the most important part of learning how to ollie. Once you learn how to do an ollie, you can try doing them while rolling. Learning is one of the funnest parts of skateboarding. After you learn ollies, you can move onto 180s, Pop Shove-Its, and flips. Soon a whole world of tricks will open up.
Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.
Place your back foot on the edge of the tail (this is where you will apply a burst of force to the skateboard) and prepare to exert force through the foot’s ‘big-toe-mound’ area. Place your front foot behind the front bolts. Make sure the weight bearing down on your feet, as well as the weight of your body, is generally centered over the ‘middle line’ of your skateboard.
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
In 1977, skate parks began cropping up all over the place, including Skateboard USA, where Gelfand began to spend most of his time. His buddy, Scott Goodman, is the one who gave Gelfand the nickname of “Ollie” and dubbed his aerial lipside the “ollie-pop.” Pictures of Gelfand during this time period clearly show him getting airborne and performing the trick associated with his name today.
The DAPANLA deck is 7.5-by-31-inches in size, on the smaller side of good quality, real skateboard decks, which makes it ideal for smaller and shorter people. Unlike many decks on the market today, the DAPANLA deck comes with non-slip grip tape on the top. The underside of the deck is similarly decorated, with a range of DAPANLA designs including the fun cartoon avocado board that is sure to turn a few heads for its uniqueness.
The KPC Series Pro Skateboard measures 8.0” x 32”. This is a common width most often associated with pro skateboarders. Wider and stronger than the rookies, this model is the perfect size for someone who is better at skating and looking for an upgrade from the rookie models. The pro features a modern concave which allows for not only comfort, but more pop making it easier to learn tricks.
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot. This is the ‘pop’. It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work. Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
Im a girl too. And here’s the deal. Guys wont bring you down unless you make a big deal out of being a girl at a skatepark. Go to a skatepark, skate until you want to stop, rock it, and stay confident. Guys could not care less whether or not you’re a girl who skates, and thats the bottom line. You just gotta learn to ollie perfectly and you’ll get to the point where you’ll be making their confidence falter.
This set-up is awesome for its price!!!! The wheels are nice and smooth (a little too big for my liking, but still good). The bearings are average (I replaced them with bones REDS). The trucks are nice and sturdy, but the bushings are kinda weak. The board is AUTHENTIC and of good dimensions. Finally, the griptape...they're all pretty much the same it's just the brand name that's different, so it doesn't matter it's all good. I would buy from this seller over and over again!!!!!!!
A skateboard is moved by pushing with one foot while the other remains on the board, or by pumping one's legs in structures such as a bowl or half pipe. A skateboard can also be used by simply standing on the deck while on a downward slope and allowing gravity to propel the board and rider. If the rider's leading foot is their right foot, they are said to ride "goofy;" if the rider's leading foot is their left foot, they are said to ride "regular." If the rider is normally regular but chooses to ride goofy, they are said to be riding in "switch," and vice versa. A skater is typically more comfortable pushing with their back foot; choosing to push with the front foot is commonly referred to as riding "mongo", and has negative connotations of style and effectiveness in the skateboarding community.
The grip tape found on a skateboard can actually be defined as the grainy sheet, which resembles sandpaper that also comes with a sticky underside. Such underside needs to adhere to the deck’s surfaces as a means of increasing traction or grip. No matter what skating style you use, the grip tape is extremely helpful in your attempt to stay on the board.
For sale I have a Powell peralta old school ripper complete red and black with 169mm independent blackout trucks blue cambria 3md 62mm wheels and bones reds bearings The deck has only been skated twice with minor scrapes on the tail and wheel wells I added the independent blackout 69mm trucks and the Cambria wheels im selling it because I’m moving in a different direction I’m building a longboard for myself for this summer anyway the deck is a reissue ripper you can’t get it anymore great overall skater very durable
If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!