Don’t get your hopes shot if it takes you a while to get this down.  Once you know how to ollie, beginner skateboarders you can do any trick in the book with just a little bit of practice.  Once you get this trick down while your stationary, go practice while moving around a little bit, try to hop off a couple of curbs.   You’ll be skateboarding like a pro in no time.  Just keep at it.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
A skateboard consists of a deck, trucks, wheels, bearings, hardware, and griptape. All parts come in a variety of sizes, graphics, colors, and signature pro series. The deck is the essential part of any skateboard. The deck ranges generally from 7.5" to 8.5". Skaters choose their board size for many reasons, but the basic deciding factor comes down to style of skating and foot size. Transition skaters usually ride a wider deck, while street skaters tend to go with a smaller deck. Skate brands such as Girl, enjoi, and Welcome offer a wide range of boards in regards to sizes and graphics. Skateboard trucks come in either a high or low setting, and also in a range of widths. The main factors in a truck, are how well they turn, and how well they grind. Independent, Venture, and Thunder, are truck brands that are well known for their turning and grinding capabilities. The skate hardware is generally either Phillips head or Allen key bolts. The skateboard wheels range from 50mm to 60mm. Some brands offer smaller and larger sizes, but 50-60mm is the general range. Like the deck sizes, wheel sizes depend on the skater's choice of terrain: Transition skaters tend to ride bigger wheels, while street skaters usually go with smaller wheels. Bones, Spitfire, Ricta, and Wayward wheel companies all make wheels for any terrain, whether you're a street shredder or a park burner. Skate bearings follow the ABEC rating system, which includes grades 1, 3, 5, 7, and 9. Bones, Bronson, and Andale are some of the top bearing brands in the skate market. CCS proudly carries all these brands, and many more.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
But there isnt a magic key or secret. Skateboarding is suprisingly a lot of brute force. That is, there is no magic secret, it’s practice practice practice. If you wanna learn any trick, keep trying that trick. There are of course proper techniques and improper, but theyre nigh impossible to describe effectively. it’s all about feel and a lot of tricks defy description.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
beginner skateboarder beginner skateboarders beginner skateboarder tips beginner skateboarding tricks common ollie mistakes get better at skateboarding get more pop how to kickflip how to ollie how to skateboard improve at skateboarding kickflip kickflip trick tip landing tricks consistently learn how to ollie learn how to skateboard ollie higher overcoming fear popping tricks higher pop shuvit pop tricks higher secrets of skateboarding skateboarding skateboarding chickenfoot skateboarding secrets skateboarding tips skateboarding tricks skateboarding trick tips skateboard tricks skateboard tricks for beginners skateboard trick tips skatepark skatepark tips style matters skateboarding tricks for beginners trick tips trips for beginner skateboarders
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve
×