Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
If you’re looking for complete skateboards that are ready to go, then you’ve come to the right place. We’ve got a great range of boards that you can ride right away, and with our next day delivery service, you’ll have your board before you know it. Browse our great selection, which includes iconic brands such as Flip, and an incredible range of colourful Penny boards and deck graphics. With so many to choose from, we’re confident you’ll find the complete skateboard you’re looking for. Buy online today and benefit for our speedy service.

Today, many riders use the “ollie-pop” on more than just the flat-level surfaces in between other tricks, it’s used heavily in the half-pipe and bowl ramps to allow the rider to go even higher in the air. Performing the “ollie-pop” while you’re at or near the top of the lip is a great way to get an extra couple feet, which might be all you need to get that extra turn in and nail the 720 (or 900, if you’re Tony Hawk).
Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.[5]
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
New Arrivals Clothing T-Shirts Shirts Sweatshirts & Hoodies Jackets Sweaters Jeans Pants Joggers & Sweatpants Shorts Boardshorts Tank Tops Shoes Sneakers Boots Sandals Slippers Shoe Care Accessories Backpacks & Bags Watches Wallets Sunglasses Hats Beanies Socks Boxers Belts Skateboards Grooming Cologne Sun Care Jewelry Stickers Hydro Flask Deals Graphic Tees 2 for $30 RSQ Jeans BOGO 50% Off Joggers BOGO 50% Off Levi's $48.99 Flannels $24.99 Sweatshirts BOGO 50% Off Tees BOGO 50% Off Backpacks 30-50% Off Collections Brixton x Coors adidas x Beavis and Butthead Diamond Supply Co. x Family Guy Disney x Vans Nixon x Disney HUF x Peanuts Primitive x Rick and Morty Vans x Marvel adidas Watches Americana Asian Inspired Street Athletic Roses Tropical Prints Camo Stripes Tie Dye Checkerboard Party Prints College Tees Rick & Morty NASA Only at Tillys
The Krown Rookie Skateboard Complete 7.5 comes with thick, sturdy 7-ply maple wood deck. It gives you more control and permits you to perform various tricks. It features carbon steel ABEC-3 bearings, aluminum trucks, bushings and 54mm x 34mm wheels. This board is perfect for kids who are 8 years and older. It has a maximum weight capacity of up to 220 lbs.
Choosing a skateboard deck can be approached in a few different ways: you can choose your board based off the graphic, the brand, the shape, the width, or even the color. For most skateboarders, it’s a combination of all these factors, but if you’ve never skateboarded before, you may not know what shape, width, or brand you like best. In this case, choosing your favorite graphic would make total sense.
A rushed take-off might be the problem here. Steps 2-4 of this trick tip could help you out. In order to make your feet “stick” to the board, you have to do the movement fluidly. But don’t stress yourself out! You should rather start with some preliminary exercises until you feel safe while ollieing. It is also important to pull your foot up to your board’s nose in a straight manner to prevent it from spinning.
Skateboard hardware is used to connect the skateboard trucks to the skateboard deck. Skateboard hardware refers to the bolts and locknuts used when building a board. The bolts can have an Allen or Phillips head. Skateboard hardware comes in many different lengths, and often includes one different colored bolt so that the rider can mark the nose of their board.
If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.

Skateboarding started in California in the 1950s.[2] The first skateboards were made from roller skates (attached to a board).[3] Skateboarding gained in popularity because of surfing; in fact, skateboarding was initially referred to as "sidewalk surfing". Initially, skateboards were handmade from wooden boxes and planks by individuals. As the sport became more popular, companies started manufacturing skateboards. Boards are also continuing to evolve as companies try to make them lighter and stronger or improve their performance.
Hey Isak I’m a 46 year old Street Skateboarder recently started Skateboarding a few months back I’m trying to get my Ollies down I’ve stopped Skating for the last couple of weeks because I was getting frustrated with not getting my Ollies I was in a funk confidence slightly knocked so I’m thinking of going Street Skating all day tomorrow and not caring about what others think it’s all in my mind I know I can do this but may mind says I’m going to slam I skate alone but shouldn’t make any difference I need help with motivation somebody give me a kick up the ass you are never to old to start Skateboarding help dudes?! Mark UK. 🙂
Bought for my 7yo's first real board, and for the price its perfect. Beginners look no further! Sure the trucks, bearings, and wheels are my choice, but as someone whose ridden for 20+ years, guarantee these items are way above Walmart status and are more than capable for you shred park or street. Bonus that it came no put together, can teach the little clone how to put it all together.

For sale I have a Powell peralta old school ripper complete red and black with 169mm independent blackout trucks blue cambria 3md 62mm wheels and bones reds bearings The deck has only been skated twice with minor scrapes on the tail and wheel wells I added the independent blackout 69mm trucks and the Cambria wheels im selling it because I’m moving in a different direction I’m building a longboard for myself for this summer anyway the deck is a reissue ripper you can’t get it anymore great overall skater very durable
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
×