Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car.  It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings.  It is ready to use and you can easily store it in your backpack.  It has an average rating of 4.5 on Amazon.
Here we have an original Z Jimmy Plumer model. It has some handling scuffing from being around for several decades, but displays great. Grip has no holes at trucks which leads me to believe it’s never had any mounted. This is one heavy fiberglass mamma jamma. Get this piece of history at a fair price. I will throw in free priority insured shipping for the con us. Everywhere else at actual cost. Thanks for looking.
To summarize, a skateboarder's feet need to do two things successfully to complete an ollie. They need to provide a changing force to move the board correctly (so that the combined force of gravity and the skater's feet add up to the green arrows above), and they need to provide different amounts of force with each foot (shown by the red and blue arrows above) to steer and turn the board into the right orientation.

Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
Regardless of your skating ability or style, CCS is the definitive place for the best skateboard decks around. With hundreds in stock, take your pick from some of the sickest decks available! Alien Workshop, Baker, Deathwish, Element, enjoi, Girl, Welcome. WKND, Santa Cruz, Primitive, and Real are among the most popular offered. Additionally, notable brands such as Almost, DGK, Flip, Krooked, Alien Workshop, Skate Mental, Zero, Creature, and Chocolate are available for all your skating needs.

So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!

Shock pads are made of polyurethane and rubber. They are very similar to risers but vary in the fact that their sole purpose is to cushion the board from the trucks. Since the trucks are metal and the board wood, whenever the board hits the ground after doing a trick, the energy goes through the truck to the board ─ this has caused boards to crack, split, or even break in half, and shock pads were created to prevent this.

Hey, welcome to the blog! My name is Billy and I've been a skateboarder now for over a decade. I know how hard it can be when learning new tricks. That’s why I decided to put up this site – to help beginner skaters find success. If you want to learn how to land skateboard tricks that will shock and amaze your friends, you've come to the right place. Bookmark this blog and come back often to learn how you can skateboard like a pro.
Rails (or ribs), are narrow strips of plastic or metal that are attached under the deck lengthwise along the edges. They are used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Rails also provide a more consistent feel for slides, as the slide of a regular skateboard will suffer from the wear of the paint or varnish on the bottom of the board. Although rarely used anymore, they are useful for experienced skaters that are capable of grabs.
If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
Learn how to ollie off of a ramp: Ramps are a LOT of fun to ollie off of, but they are also a great way to break something if you don't know what you're doing! I have a cousin who almost lost his arm because of how nastily he broke it while ollying off a ramp. But don't let that scare you - if you know what you're doing, ollying off ramps is great!
Skateboarding is all about creativity and finding new challenges. A great way to explore skateboarding is to ride different shaped boards, wider trucks, and different size wheels. As you progress and start to ride new terrain and skate different kinds of spots, you may find one wheel size or board shape works better for you than another. There’s no wrong or right anything. There are no rules. Except for maybe one, and that is to keep skating. Skate as often as you can. Never is this more true than in the beginning while you’re developing your style and fundamentals.
Maybe you're new to skateboarding. We have lots of complete skateboards or longboards to get you started. All of our skateboard and longboard completes come fully assembled, so you can hit the streets without any of the hassle—try an Enjoi skateboard complete or check out our selection of Sector 9 longboard and skateboard completes. Or maybe you're an experienced skater looking to update and customize your ride. You probably want to start with the perfect skateboard deck before you do anything else. We carry high-quality skate decks to keep you steady and balanced while you bomb, slide, and carve the streets. We also have a variety of longboard decks in stock if you're looking for a smooth ride for cruising or commuting.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
×