This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
Hey, welcome to the blog! My name is Billy and I've been a skateboarder now for over a decade. I know how hard it can be when learning new tricks. That’s why I decided to put up this site – to help beginner skaters find success. If you want to learn how to land skateboard tricks that will shock and amaze your friends, you've come to the right place. Bookmark this blog and come back often to learn how you can skateboard like a pro.

Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.


Pull your knees up into your chest – How far you actually want to pull your legs up is totally up to you, but the higher your feet go, the higher your board will go too. By the way, the highest recorded preferred stance ollie-pop is 45 inches, done by Aldrin Garcia, and the highest switch stance ollie-pop is 40.125 inches, by Gavin Caperton. And if you’re going for endurance rather than height, the record for most consecutive hops is held by Rob Dyrdek, who did 215 of them in a row on his TV show Rob and Big. So those give you something to shoot for.


A skateboard is moved by pushing with one foot while the other remains on the board, or by pumping one's legs in structures such as a bowl or half pipe. A skateboard can also be used by simply standing on the deck while on a downward slope and allowing gravity to propel the board and rider. If the rider's leading foot is their right foot, they are said to ride "goofy;" if the rider's leading foot is their left foot, they are said to ride "regular." If the rider is normally regular but chooses to ride goofy, they are said to be riding in "switch," and vice versa. A skater is typically more comfortable pushing with their back foot; choosing to push with the front foot is commonly referred to as riding "mongo", and has negative connotations of style and effectiveness in the skateboarding community.
It comes with a plastic board deck, which is small in size, making it ideal for riders who need a really sturdy skateboard. It is more suitable for both experts and beginners who want to learn new tricks in skateboarding. The fact that it is stable and small makes it good for kids, too. It promotes ease in riding and controlling it in a crowded street. This complete skateboard is lightweight, too, allowing you to carry it almost everywhere.

New Arrivals Clothing T-Shirts Shirts Sweatshirts & Hoodies Jackets Sweaters Jeans Pants Joggers & Sweatpants Shorts Boardshorts Tank Tops Shoes Sneakers Boots Sandals Slippers Shoe Care Accessories Backpacks & Bags Watches Wallets Sunglasses Hats Beanies Socks Boxers Belts Skateboards Grooming Cologne Sun Care Jewelry Stickers Hydro Flask Deals Graphic Tees 2 for $30 RSQ Jeans BOGO 50% Off Joggers BOGO 50% Off Levi's $48.99 Flannels $24.99 Sweatshirts BOGO 50% Off Tees BOGO 50% Off Backpacks 30-50% Off Collections Brixton x Coors adidas x Beavis and Butthead Diamond Supply Co. x Family Guy Disney x Vans Nixon x Disney HUF x Peanuts Primitive x Rick and Morty Vans x Marvel adidas Watches Americana Asian Inspired Street Athletic Roses Tropical Prints Camo Stripes Tie Dye Checkerboard Party Prints College Tees Rick & Morty NASA Only at Tillys
In most cases, it is available in black but you can also find clear ones that are ideal for you if you want to show a specific logo. Another nice choice that you have is the die-cut grip tape, which works in displaying the color or design of the deck beneath it. Make sure to choose a grip tape at a size, which perfectly suits your skateboard’s deck.

Low ollies: This can happen for a lot of reasons, but the biggest one is that you are not crouching low enough before your ollie, and not pulling your feet high enough after you jump. When you crouch down, try and touch the ground. When you jump, try to hit yourself in the chest with your knees. ​Both knees. Don’t worry about falling. That will happen sometimes – that’s just part of skateboarding! For more help, read the How Can I Make My Ollies Higher? FAQ
So you want to know how to ollie? Be warned, it’s not for the faint of heart, and a lot of people have tried and failed and tried some more and still failed and then eventually thrown their boards into a wall out of frustration (I have no idea who those people are). It’s by no means an easy skateboard trick, but if you want to know how to ollie, start with these simple tips:
The Landwalker 22″ Complete Skateboard has a sturdy 7 layer Canadian maple deck. It’s best for downhill, U table and slider because of its enormous stability. This board is best for teens and adults. It comes with Abec 7″ Bearings, PU wheels, Black Grip Tape, and hardware. It measures 79 x 20 x 10 cm. This board is an awesome gift for Christmas or Halloween.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
Hey, welcome to the blog! My name is Billy and I've been a skateboarder now for over a decade. I know how hard it can be when learning new tricks. That’s why I decided to put up this site – to help beginner skaters find success. If you want to learn how to land skateboard tricks that will shock and amaze your friends, you've come to the right place. Bookmark this blog and come back often to learn how you can skateboard like a pro.

Rails (or ribs), are narrow strips of plastic or metal that are attached under the deck lengthwise along the edges. They are used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Rails also provide a more consistent feel for slides, as the slide of a regular skateboard will suffer from the wear of the paint or varnish on the bottom of the board. Although rarely used anymore, they are useful for experienced skaters that are capable of grabs.

It's a neat piece of science art, and it also tells us something interesting. The arrows show us that the force on the skateboard is constantly changing, both in magnitude as well as in direction. Now the force of gravity obviously isn't changing, so the reason that these force arrows are shrinking and growing and tumbling around is that the skater is changing how their feet pushes and pulls against the board. By applying a variable force that changes both in strength and direction, they're steering the board.
As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
×