Don’t get your hopes shot if it takes you a while to get this down.  Once you know how to ollie, beginner skateboarders you can do any trick in the book with just a little bit of practice.  Once you get this trick down while your stationary, go practice while moving around a little bit, try to hop off a couple of curbs.   You’ll be skateboarding like a pro in no time.  Just keep at it.
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.

Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.


    Almost no one lands an ollie on their first try.  Repetition is the most important part of learning how to ollie.  Once you learn how to do an ollie, you can try doing them while rolling.  Learning is one of the funnest parts of skateboarding.  After you learn ollies, you can move onto 180s, Pop Shove-Its, and flips.  Soon a whole world of tricks will open up.
Rails (or ribs), are narrow strips of plastic or metal that are attached under the deck lengthwise along the edges. They are used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Rails also provide a more consistent feel for slides, as the slide of a regular skateboard will suffer from the wear of the paint or varnish on the bottom of the board. Although rarely used anymore, they are useful for experienced skaters that are capable of grabs.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
The wheels are also impressive. Unlike some other skateboards that have wheels that are quite stiff, causing them to feel like they will lock up when you ride on them, the wheels in this complete skateboard for beginners are smooth and comfortable. These are also easily controllable, so rest assured that they offer a smooth and friction-free glide.
×