Rails (or ribs), are narrow strips of plastic or metal that are attached under the deck lengthwise along the edges. They are used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Rails also provide a more consistent feel for slides, as the slide of a regular skateboard will suffer from the wear of the paint or varnish on the bottom of the board. Although rarely used anymore, they are useful for experienced skaters that are capable of grabs.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
The most important thing when you learn to skateboard is to skate with people that are at a higher skill lv than you, then they can tell you what you are doin wrong. Its so **cing anoing when you skate alle alone, wondering why your board is turning, and you haw to go to the internet to find out that it is something so easy as ceeping your shoulders straight.
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
BRANDS Acembly adidas Amuse Society Asphalt Billabong Birkenstock Blue Crown Brixton Burton Calvin Klein Captain Fin Champion Charles and a Half Converse DGK Diamond Supply Co. Dickies Dr. Martens Electric Element Elwood Ethika FILA Fox Full Tilt G Shock Grizzly Herschel Supply Co. HippyTree Hoonigan HUF Hurley Hydro Flask Imperial Motion Ivy & Main JanSport Kendall & Kylie King Ice La Familia Last Call Co. Levi's Lira Loser Machine Lost LRG Neff New Balance Nike SB Nixon O'Neill OP Others Follow Patrons Of Peace Penny Pink Dolphin Popsockets Primitive Skateboarding PSD Puma Quiksilver Rainbow Rastaclat Ray Ban Rebel8 Reebok Reef Riot Society Rip Curl Roark Roxy RSQ Russell Athletic Rusty RVCA Salty Crew Santa Cruz Sky and Sparrow Soda Spy Stance Suavecito The North Face Timberland Tommy Hilfiger TOMS Under Armour Vans Vissla Vogue Eyewear Volcom Von Zipper Young & Reckless VIEW ALL BRANDS
Punisher Skateboards Warphant measures 31 x 7.5 inch.  It has a 9-Ply Maple Black Board with Concave Deck and Double Kick Tail.  It comes with ABEC-3 Bearings, 5-inch V-style Heavy Duty Alloy Trucks, and Bases.  It uses 54 x 36 mm PU injection molded wheels and PE Riser Pad with PU Cushion and Punisher Logo.  It is perfect for learning and doing tricks.  It is best suited for riders who are 8 years old and above.  It has a 5 rating on Amazon.
It is mainly because those items are guaranteed to help you familiarize yourself with the ins and outs of using them. They are a big help in making you feel comfortable when you push off with your feet while also balancing on top of the board when riding. It is not good to go for a very technical product, so it’s best to choose the mentioned types first.
Almost is proud to announce a collaboration with Skateistan, the award-winning non-profit organization empowering children and youth through skateboarding and education. They recently launched a new Skate School in Phnom Penh, Cambodia on Friday (February 23rd, 2018). Over 100 children celebrated alongside special guests from around the world, including Almost flow skater Sky Brown. 
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
Aaron "Jaws" Homoki Aaron Herrington Aidan Campbell Al Davis Al Partanen Alec Majerus Alex Midler Alexis Sablone Andrew Brophy Andrew Reynolds Auby Taylor Austin Kanfoush Axel Cruysberghs Bam Margera Barney Page Ben Gore Ben Hatchell Ben Krahn Ben Raemers Ben Raybourn Billy Marks Blake Carpenter Bobby de Keyzer Bobby Worrest Boo Johnson Brad Cromer Brad McClain Brad Staba Brandon Biebel Brandon Westgate Brian "Slash" Hansen Brian Anderson Brian Delatorre Brian Downey Brian Lotti Bryan Herman Carlos Iqui Casper Brooker Caswell Berry Charlie Blair Chase Webb Chico Brenes Chima Ferguson Chopper Chris Cole Chris Gregson Chris Haslam Chris Joslin Chris Miller Chris Pfanner Chris Roberts Chris Russell Chris Troy Christian Hosoi Christian Maalouf Claus Grabke Clint Walker Clive Dixon Cody Lockwood Cody McEntire Cole Wilson Collin Provost Cooper Wilt Corey Duffel Corey O'Brien Cory Kennedy Craig "Questions" Scott Cyril Jackson Daan Van Der Linden Daewon Song Dakota Servold Dan Drehobl Dan Plunkett Dane Brady Dane Burman Dane Vaughn Daniel Castillo Daniel Lutheran Danny Cerezini Danny Falla Danny Garcia Danny Montoya Danny Renaud Danny Way Darren Navarrette Dave Abair Dave Caddo David Gonzalez David Gravette Davis Torgerson Dee Ostrander Dennis Busenitz Don "Nuge" Nguyen Dustin Dollin Ed Selego Ed Templeton Emmanuel Guzman Eric Dressen Eric Koston Erick Winkowski Erik Ellington Evan Smith Felipe Gustavo Frank Gerwer Frankie Hill Gilbert Crockett Glen Fox Grant Taylor Gustav Tonnesen Guy Mariano Henry Sanchez Hiroki Muraoka Hjalte Halberg Ishod Wair Jack Curtin Jack Given Jackson "Jacko" Shapiera Jackson Pilz Jake Hayes Jake Johnson Jam Douglas James Brockman Jamie Foy Jamie Lynn Jamie Palmore Jamie Tancowny Jamie Thomas Jarne Verbruggen Jason Adams Jason Jessee Javier Sarmiento Jay Adams Jeff Grosso Jeff Kendall Jeremy Leabres Jeron Wilson Jesse Narvaez Jesus Fernandez Jim Greco Jim Thiebaud Jimmy Cao Jimmy Lannon Jimmy Wilkins Joey Guevara Joey Pepper Johan Stuckey John Cardiel John Grigley John Lucero John Lupfer John Motta Jon Dickson Jon Nguyen Jordan Hoffart Jordan Maxham Jordan Sanchez Jordan Taylor Josef Scott Jatta Josh Kalis Josh Matthews Josh Pall Julian Davidson Julien Stranger Justin "Figgy" Figueroa Justin Brock Justin Eldridge Kellen James Kelvin Hoefler Kenny Anderson Kevin "Spanky" Long Kevin Baekkel Kevin Coakley Kevin Romar Kevin Taylor Kyle Leeper Kyle Nicholson Kyle Walker Lance Mountain Lee Yankou Leo Romero Leo Valls Leticia Bufoni Lewis Marnell Lizzie Armanto Louie Barletta Louie Lopez Madars Apse Mark "Gonz" Gonzales Mark Appleyard Marquise Henry Marshall Heath Mason Silva Matt Berger Matt Hensley Matt Tomasello Mike "Lizard King" Plumb Mike Anderson Mike Arnold Mike Carroll Mike McGill Mike Mo Capaldi Mike Vallely Miles Silvas Milton Martinez Morgan Smith Natas Kaupas Neen Williams Nestor Judkins Nick Boserio Nick Garcia Nicky Guerrero Nisse Ingemarsson Nora Vasconcellos Nyjah Huston Omar Hassan Oskar Rozenberg Hallberg P.J. Ladd Paul Grund Per Welinder Peter Hewitt Peter Ramondetta Phil Hansen Quim Cardona Raney Beres Raven Tershy Ray "Bones" Rodriguez Ray Barbee Raymond Molinar Rich Adler Rick Howard Rick McCrank Ricky Oyola Riley Hawk Rob Gonzalez Rob Roskopp Robbie Brockel Robbie Russo Rodney Mullen Rodrigo "TX" Teixeira Rodrigo Petersen Ronnie Sandoval Rowan Zorilla Rudy Johnson Ryan Decenzo Ryan Lay Ryan Reyes Ryan Spencer Ryan Townley Sam Beckett Sam Hitz Samarria Brevard Sammy Baca Scott Decenzo Sean Malto Sebo Walker Shawn Hale Silas Baxter-Neal Simon Isaksson Soy Panday Stefan Janoski Steve Caballero Steve Ortega Steve Saiz Stevie Perez Stevie Williams Stu Graham Sylvain Tognelli T.J. Rogers Taylor Kirby Terry Kennedy Thaynan Costa Theotis Beasley Tiago Lemos Tim O'Connor Tobin Valverde Tom Asta Tom Karangelov Tom Knox Tom Knox (80s) Tommy Fynn Tommy Guerrero Tommy Sandoval Tony Hawk Tony Karr Tony Trujillo Torey Pudwill Trevor McClung Tristan "Tfunk" Funkhouser Tyler Bledsoe Tyler Surrey Tyson Peterson Vincent Alvarez Vivien Feil Wade Desarmo Wes Kremer Wieger Van Wageningen Willis Kimbel Windsor James Yaje Popson Yonnie Cruz Yoshi Tanenbaum Youness Amrani Yuri Facchini Zach Lyons Zack Wallin Zered Bassett Zion Wright
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
EXPERIENCED SKATER! This board is amazing for the price! (notice i said FOR THE PRICE) At the time of this review, the board was $44.40 and for that price the board i got was phenomenal. It is a 7-ply deck with aluminum trucks (havent figured out the bearings but they definitely feel like the abec 5 they claim to be). The trucks arent the best quality out there and the board can be a little thinner (maybe 5-ply) but the overall board is amazing. There are only two complaints. The hole in the wheels is a tiny TINY TIIINYYY bit off center, but nothing that cant be fixed with a new set. I can see what another review said by it not coming assembled, as a couple of the bolts on the wheels are a little loose, but the board does come assembled.
Pop the board in the air – The reason you jump up into the air in the first place is because you’re slamming the back end into the ground (don’t worry, your board is made to take the abuse). It’s the same motion you would do if you were standing near the board and wanted to pop the board up into your hands, except this time, you’re standing on top of it. As soon as you feel the board pop into the ground, kick your front foot up into the air at the same time. The timing on this is important: kick too early and you won’t go anywhere, kick too late and your board will fly out from underneath you.
This set-up is awesome for its price!!!! The wheels are nice and smooth (a little too big for my liking, but still good). The bearings are average (I replaced them with bones REDS). The trucks are nice and sturdy, but the bushings are kinda weak. The board is AUTHENTIC and of good dimensions. Finally, the griptape...they're all pretty much the same it's just the brand name that's different, so it doesn't matter it's all good. I would buy from this seller over and over again!!!!!!!
In 1977, skate parks began cropping up all over the place, including Skateboard USA, where Gelfand began to spend most of his time. His buddy, Scott Goodman, is the one who gave Gelfand the nickname of “Ollie” and dubbed his aerial lipside the “ollie-pop.” Pictures of Gelfand during this time period clearly show him getting airborne and performing the trick associated with his name today.

Go for the low truck profile if you want to obtain additional stability when you do flip tricks. It also works well for small wheels. The mid-sized trucks are good for all-around use, especially in streets and parks. You can also choose the high-sized trucks that are good for carving and cruising, which is the reason why they are perfect for huge wheels.
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
Punisher Skateboards Warphant measures 31 x 7.5 inch.  It has a 9-Ply Maple Black Board with Concave Deck and Double Kick Tail.  It comes with ABEC-3 Bearings, 5-inch V-style Heavy Duty Alloy Trucks, and Bases.  It uses 54 x 36 mm PU injection molded wheels and PE Riser Pad with PU Cushion and Punisher Logo.  It is perfect for learning and doing tricks.  It is best suited for riders who are 8 years old and above.  It has a 5 rating on Amazon.
Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.

EXPERIENCED SKATER! This board is amazing for the price! (notice i said FOR THE PRICE) At the time of this review, the board was $44.40 and for that price the board i got was phenomenal. It is a 7-ply deck with aluminum trucks (havent figured out the bearings but they definitely feel like the abec 5 they claim to be). The trucks arent the best quality out there and the board can be a little thinner (maybe 5-ply) but the overall board is amazing. There are only two complaints. The hole in the wheels is a tiny TINY TIIINYYY bit off center, but nothing that cant be fixed with a new set. I can see what another review said by it not coming assembled, as a couple of the bolts on the wheels are a little loose, but the board does come assembled.

In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.
The Wasatch Imports Good Skateboards is the ultimate compact and complete street board that is ready-to-go. It is great for exercise and fun. It is very portable and perfect for all skill levels. It has a variety of awesome vintage color combinations that you can choose from. It is made of topline construction, with a high-density plastic deck, 59mm super smooth wheels, ABEC7 bearings, and solid aluminum trucks. It measures 22″ long and 6″ wide and weighs 4 pounds. It has a  full manufacturer’s lifetime warranty on all parts, pieces, and materials. It has a weight limit of 200 pounds which can ensure that bigger skaters can join the fun.
The ollie is a skateboarding trick where the rider and board leap into the air without the use of the rider's hands.[1] It is basically the combination of popping, sliding, and jumping on the skateboard all at the same time. Originated in vertical skateboarding, and later on flat ground, it is not intuitively obvious how the liftoff is achieved, making the movement visually striking.

My problem is that my board always lands crooked when I Ollie. The worst thing is that I even tell myself to “keep your shoulders straight” while I’m doing the Ollie and I still land crooked. I think it’s just hard for people to grasp the simple fact that everything on a skateboard has to be done horizontally which is odd because people don’t walk sideways. We walk straight. Like roller blading for example…. it’s easier for me to roller blade because I’m used to walking and running obviously except with a skateboard everything is as if you were hopping over a fence sideways. Skateboarding is tough.
Punisher Skateboards Warphant measures 31 x 7.5 inch.  It has a 9-Ply Maple Black Board with Concave Deck and Double Kick Tail.  It comes with ABEC-3 Bearings, 5-inch V-style Heavy Duty Alloy Trucks, and Bases.  It uses 54 x 36 mm PU injection molded wheels and PE Riser Pad with PU Cushion and Punisher Logo.  It is perfect for learning and doing tricks.  It is best suited for riders who are 8 years old and above.  It has a 5 rating on Amazon.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
New Arrivals Clothing Dresses & Rompers Tops Sweaters Sweatshirts & Hoodies Jackets Jeans Pants Leggings Shorts Skirts Swim Intimates Bras Panties Bodysuits Intimate Accessories Shoes Sneakers Boots & Booties Sandals Flats Heels & Wedges Slippers Accessories Backpacks Bags & Wallets Hats & Beanies Jewelry Hair Accessories Sunglasses Socks Belts Watches Scarves Hydro Flask Beauty Hair Bath & Body Makeup Fragrance Sun Care Brushes & Tools Deals RSQ Jeans BOGO 50% Off Sweaters BOGO 50% Off Sweatshirts BOGO 50% Off Tops 4 for $25 Tees 2 for $20 Backpacks 30-50% Off Panties 5 for $16 Bralettes BOGO 50% Off Vogue Sunglasses 40% Off Sunglasses 50% Off Jewelry BOGO 50% Off Sunglasses 2 for $15 Trends COZY SHOP Riverdale Zipper Details Corduroy Color Trends Menswear Florals Stripes Checkered Button Front Tie Front Tie Dye & Crystal Wash Disney X Vans Converse X Hello Kitty Levi's X Mickey Only at Tillys
Choosing a skateboard deck is a great place to start when building a complete skateboard. Unless you have experience riding a shaped board - something a little more retro or unusual, we recommend you start with a popsicle shape. CCS carries over 60 different skateboard deck brands that sell this popular popsicle shape. If you have questions on what size you should ride or have any other questions about building a complete, we recommend you check out our Skateboard Buyer’s Guide. Here, you’ll find helpful how-to’s for choosing a skateboard decks, skateboard trucks, skateboard wheels, skateboard bearings, and skateboard components. This guide explains every part of a skateboard and helps you choose which sizes and styles to best suit your needs.
The skateboard has a solid and stiff mini-deck, which is around 22 inches and constructed out of 100% plastic material. Such deck is very lightweight. It is only four pounds but you have an assurance that it can handle up to 198 lbs. of weight. You will also fall in love with the board as it comes in 23 graphics and colors, so picking a favorite is much easier.

Krown burst on to the skate scene back in 1996 with the idea to provide a high quality skateboard to the rider on a budget. Krown recognized a big gap between the $20 big box retail skateboard and the $150 professional grade skateboard. The boards at big box retail stores have plastic wheels and don’t even roll! Krown’s idea to bring a price-point skateboard to the market that actually functions as a skateboard has proven to be successful after more than 20 years. With more than 20 years of industry knowledge and knowhow, Krown is able to source the best parts at the best prices, which allows Krown to pass the savings on to the consumer. This expertise has allowed Krown to venture into the world of skateboards, longboards, helmets, pads, and even tools. Krown is the best place to start for beginner and intermediate riders!
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.
A skateboard is moved by pushing with one foot while the other remains on the board, or by pumping one's legs in structures such as a bowl or half pipe. A skateboard can also be used by simply standing on the deck while on a downward slope and allowing gravity to propel the board and rider. If the rider's leading foot is their right foot, they are said to ride "goofy;" if the rider's leading foot is their left foot, they are said to ride "regular." If the rider is normally regular but chooses to ride goofy, they are said to be riding in "switch," and vice versa. A skater is typically more comfortable pushing with their back foot; choosing to push with the front foot is commonly referred to as riding "mongo", and has negative connotations of style and effectiveness in the skateboarding community.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air.[2] While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.[citation needed]
×