The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.
The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.
Velocity Boards Retro Banana Skateboard is a 22″ Complete Board Set with 6″ Aluminum Trucks, ABEC-7 Bearings, High-Quality Wheels, and Bushings. It is designed for maximum grip. The Deck measures about 22 x 6 x 4″. The truck Axle has a Width of 6″ and the Truck Hanger has a Width of 3″. It has a maximum load capacity of 176 lbs. (80 kgs.) It is best for skaters who are 6 years old and Up. It has an average Amazon rating of 4.7.
In 1977, skate parks began cropping up all over the place, including Skateboard USA, where Gelfand began to spend most of his time. His buddy, Scott Goodman, is the one who gave Gelfand the nickname of “Ollie” and dubbed his aerial lipside the “ollie-pop.” Pictures of Gelfand during this time period clearly show him getting airborne and performing the trick associated with his name today.
Jump – Ah yes, finally, we have reached the move itself. Basically, you have to do about twelve different things all at once to execute a successful ollie-pop: lift your front foot, press down with your back foot, angle your front ankle, and jump. Lift the front foot off the ground first, and then move your back foot. This whole process is easier if you’re actually moving forward – since you don’t have to fight for balance – but it can be done while you’re standing still as well.
The wheels are also impressive. Unlike some other skateboards that have wheels that are quite stiff, causing them to feel like they will lock up when you ride on them, the wheels in this complete skateboard for beginners are smooth and comfortable. These are also easily controllable, so rest assured that they offer a smooth and friction-free glide.
The ollie is a skateboarding trick where the rider and board leap into the air without the use of the rider's hands. It is basically the combination of popping, sliding, and jumping on the skateboard all at the same time. Originated in vertical skateboarding, and later on flat ground, it is not intuitively obvious how the liftoff is achieved, making the movement visually striking.
In general an axle width should be chosen that is close to the width of the deck it will be used with. For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.