The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Sublimation (phase transition) is the transition of a substance directly from the solid to the gas phase without passing through an intermediate liquid phase. Sublimation is an endothermic phase transition that occurs at temperatures and pressures below a substance's triple point in its phase diagram. In this case, ink is transferred to a base layer, fibreglass for example, through heat and pressure, the result is a full color graphic that will not come off as easily as the more common heat transfers. This application is often found with bamboo boards and composite construction longboards where fibreglass can allow for various degrees of flex or stiffness depending on the ride you're looking for, cruising and carving versus slalom and downhill.

Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.


Low ollies: This can happen for a lot of reasons, but the biggest one is that you are not crouching low enough before your ollie, and not pulling your feet high enough after you jump. When you crouch down, try and touch the ground. When you jump, try to hit yourself in the chest with your knees. ​Both knees. Don’t worry about falling. That will happen sometimes – that’s just part of skateboarding! For more help, read the How Can I Make My Ollies Higher? FAQ
Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
I have been doing ollie’s for about a year to a year and a halve, but thats not the problem. My problem is the board turns when i ollie, i cant help it, i am starting to go into harder ground (ollying off ledges and ollying stairs) but i cant land and ride away because my board has turned in a 45 degree angle and it jerks me off the board, Please help in all you can, cheers mate.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
The KPC Series Pro Skateboard measures 8.0” x 32”. This is a common width most often associated with pro skateboarders. Wider and stronger than the rookies, this model is the perfect size for someone who is better at skating and looking for an upgrade from the rookie models. The pro features a modern concave which allows for not only comfort, but more pop making it easier to learn tricks.
The Bamboo Mini Cruiser deck is 6-inches-by-22.5-inches with that classic cruiser shape. The board is made with 6-ply bamboo and maple construction, which is lightweight, flexible and eco-friendly. Bamboo Skateboards claims this board has a turning radius not seen in most mini decks. The small, blank deck is heavy duty and durable in a way not all mini cruisers are. The non-carbonized board is ready for you to slap on the grip tape and artwork you want and then get riding.
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
×