The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
My problem is that my board always lands crooked when I Ollie. The worst thing is that I even tell myself to “keep your shoulders straight” while I’m doing the Ollie and I still land crooked. I think it’s just hard for people to grasp the simple fact that everything on a skateboard has to be done horizontally which is odd because people don’t walk sideways. We walk straight. Like roller blading for example…. it’s easier for me to roller blade because I’m used to walking and running obviously except with a skateboard everything is as if you were hopping over a fence sideways. Skateboarding is tough.

When learning it, you will, slip and fall. Feel like an idiot doing something over and over again and not getting it, feel fear bcos you don’t know what's going to happen to you once you pop the tail, jump and slide your foot and then you land. Will you land on your board, will you be on the pavement? Will you slip out, will u kick the board away, will you land primo? No one knows but you gotta try it out and find it out yourself. Whatever it is, don't give up cos it's the strength to persevere, be crazy persistent to achieve and most of all being patient in learning and progressing that let's you earn the skateboarder title for your ownself.
Any serious skateboarder will tell you that the ollie is the most fundamental skateboard trick. In fact, it's probably the first trick that you'll learn on your skateboard. They’re great for getting over obstacles, moving around on your board, or just looking cool. Know the right way to move your feet on the board and with a little bit of practice, you can learn to pull off the perfect ollie.

Regardless of your skating ability or style, CCS is the definitive place for the best skateboard decks around. With hundreds in stock, take your pick from some of the sickest decks available! Alien Workshop, Baker, Deathwish, Element, enjoi, Girl, Welcome. WKND, Santa Cruz, Primitive, and Real are among the most popular offered. Additionally, notable brands such as Almost, DGK, Flip, Krooked, Alien Workshop, Skate Mental, Zero, Creature, and Chocolate are available for all your skating needs.
Pull your knees up into your chest – How far you actually want to pull your legs up is totally up to you, but the higher your feet go, the higher your board will go too. By the way, the highest recorded preferred stance ollie-pop is 45 inches, done by Aldrin Garcia, and the highest switch stance ollie-pop is 40.125 inches, by Gavin Caperton. And if you’re going for endurance rather than height, the record for most consecutive hops is held by Rob Dyrdek, who did 215 of them in a row on his TV show Rob and Big. So those give you something to shoot for.
The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.

Sublimation (phase transition) is the transition of a substance directly from the solid to the gas phase without passing through an intermediate liquid phase. Sublimation is an endothermic phase transition that occurs at temperatures and pressures below a substance's triple point in its phase diagram. In this case, ink is transferred to a base layer, fibreglass for example, through heat and pressure, the result is a full color graphic that will not come off as easily as the more common heat transfers. This application is often found with bamboo boards and composite construction longboards where fibreglass can allow for various degrees of flex or stiffness depending on the ride you're looking for, cruising and carving versus slalom and downhill.
Velocity Boards Retro Skateboards is a complete 22″ Banana Skateboard.  It includes 6″ Lightweight Aluminum Trucks, High-Speed ABEC-7 Bearings, High-Quality Wheels & Bushings and Hardware.  It has a Unique Textured Waffle Pattern on Deck and is designed for Maximum Grip.  The Deck measures about 22 x 6 x 4″.  It has a 6″ Truck Axle and a 3″ Truck Hanger.  It has a maximum weight capacity of  176 lbs. (80 kgs.).  It is great for all skaters who are 6 years old and above.  It has an Amazon rating of 4.7.

For sale I have a Powell peralta old school ripper complete red and black with 169mm independent blackout trucks blue cambria 3md 62mm wheels and bones reds bearings The deck has only been skated twice with minor scrapes on the tail and wheel wells I added the independent blackout 69mm trucks and the Cambria wheels im selling it because I’m moving in a different direction I’m building a longboard for myself for this summer anyway the deck is a reissue ripper you can’t get it anymore great overall skater very durable


The wheels are also impressive. Unlike some other skateboards that have wheels that are quite stiff, causing them to feel like they will lock up when you ride on them, the wheels in this complete skateboard for beginners are smooth and comfortable. These are also easily controllable, so rest assured that they offer a smooth and friction-free glide.
Rails (or ribs), are narrow strips of plastic or metal that are attached under the deck lengthwise along the edges. They are used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Rails also provide a more consistent feel for slides, as the slide of a regular skateboard will suffer from the wear of the paint or varnish on the bottom of the board. Although rarely used anymore, they are useful for experienced skaters that are capable of grabs.
One foot on the tail, (by foot I mean the ball of the foot which is just behind the big toe) the other foot is about an inch behind the bolts(screws) for the front truck. Basically, the back foot quickly pushes the tail down, and right when the tail of the board strikes the ground, the back foot jumps up… the tail of the board will follow up with the foot when the front foot slides forward slightly, which pivots the tail of the board upwards. Since the front truck comes off the ground first, getting the back truck up is the trick.
Radiate Ride Good Skateboards are made of 7-ply maple construction with epoxy resin glue. It features 356A heat-treated cast aluminum high performance 5.0 trucks with grade 8 kingpins and axles. The super high rebound 99A PU wheels with grooved running surface provide better traction and abrasion resistance. The Abec 5 high precision speed bearings offer precision performance and a smooth ride. It has an 80 grit durable color matched grip tape with transparency. It is completely assembled and ready to go. This product has a 4.3 rating on Amazon.
The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
In this modern era, manufacturers are incorporating hi-tech processes and top-shelf materials into the construction of the skateboard. Companies such as Almost have several versions of hi-tech decks such as the Impact, Double Impact, and Uber Light Series. Element makes Highlight decks with inlayed fiberglass beams, and Foundation has its signature Fiberprime decks. Other manufactures such as Flip, Habitat, Plan B, Skate Mental, and Zero offer boards with high-end P2 Construction. Hi-tech decks differ from traditional 7-ply Maple in that they are inlayed with Carbon Fiber, Fiberglass, Poly Ply, or Kevlar to produce a stronger skateboard with more pop. For more options, head over to our stellar selection of Hi-Tech Decks! Although hi-tech decks have made a strong presence within the market, standard 7-ply Maple remain the gold standard. This is due to the solid feeling and pop afforded through layering 7 Maple wood veneers together. The large majority of skateboard decks offered are constructed of 7-ply Maple. Most board manufacturers offer both high-tech decks and standard 7-ply Maple. No matter what you desire, CCS offers a complete selection in multiple sizes, shapes, and construction types!
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
My fiancee purchased this via my account and he says that it has good concave shape and pop.Assembling was fairly simple, easier if you have a box cutter on hand to help with laying the grip tape. The deck was the best part but the bearings were good too. He thought the bushings were the worst, after about two hours of skating, both bushings were crushed and stuck in one direction. He's been skating for almost 13 years. Hope this helps!
Do your Ollie, then, instantly after you pop your board, lift your back foot up to meet your front foot. That helped me solo much I improved twice in a few tries with using that trick. And, if that doesn’t help, it’s just a matter of practicing. If you practice a ly every day, you experiment, you will find u r solution. But, try lifting u r back foot high right after u pop 😉
The fact that it has nice and attractive prints also makes it a fashion skateboard. You can use it to show not only your passion in the sport but also your fashion sense. It is also equipped with a high-density emery surface known for being both waterproof and non-slip. With that, you have a hundred percent assurance of your safety when you are riding on it.
Mini Cruisers have exploded in popularity in recent years. These short and skinny boards are may not have the versatility of a standard skateboard, allowing for a full range of tricks and travel. However, these compact boards are ideal for urban and college living where space for storage and riding are both minimal. If you want to ride a mini-cruiser, but you hate the plastic decks or you want to build your own, check out the Bamboo Skateboard mini cruiser deck.

Pop in your earbuds and head to the skate park with a skateboard that rolls through impressive stunts with ease. Most skateboards for sale offer strong wood decks that create a stable feel beneath your feet as you work on your grind and backslide techniques, but models with polypropylene construction offer a lightweight alternative with plenty of toughness. Try a surfboard-inspired design to cruise the streets like you'd ride a wave, or select a drop-through deck for smooth cruising. Grip tape promotes sure footing that helps you ride with confidence, but always put safety first - wear a skate helmet and skate pads from our Skateboard Shop for protection against mid-move falls.
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.

Both your height and weight should play an important role when you are choosing a skateboard. You need to find a skateboard, which fits your weight and height. Picking one, which is either too small or too big might only cause you to experience difficulty controlling it, especially if you are still a beginner learning the ins and outs of skateboarding.


Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?
It’s not just standard deck sizes that are available for creating or replacing your board. You can just as easily get a great longboard deck to work on in your basement or garage. One of the best and best reviewed options out there is the Loaded Boards Poke Longboard Skateboard Deck. This standard-design longboard deck has it all to help you make the ideal board. 
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
×