Pop the board in the air – The reason you jump up into the air in the first place is because you’re slamming the back end into the ground (don’t worry, your board is made to take the abuse). It’s the same motion you would do if you were standing near the board and wanted to pop the board up into your hands, except this time, you’re standing on top of it. As soon as you feel the board pop into the ground, kick your front foot up into the air at the same time. The timing on this is important: kick too early and you won’t go anywhere, kick too late and your board will fly out from underneath you.
In general an axle width should be chosen that is close to the width of the deck it will be used with. For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
The Element Quadrant #14 board is 8-inches wide and 31.75-inches long, from nose to tail. This deck features a bare top that needs grip tape and a design on the bottom with four quadrants featuring the Element symbol in alternating red and black backgrounds. The wheelbase between the trucks is just over 14 inches while the nose is 7 inches and the tail is 6.325.
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.
A complete skateboard is pre-assembled - it almost rides right out of the package and on to the streets, ready for you to practice all your new tricks. You simply don’t have to think about buying the separate parts like trucks, wheels, decks or the likes. Once you have gained more experience on the board and you feel like customizing it to fit your skateboarding style, you can begin to learn more about the different pieces in order to assemble a skateboard that meets your specific wishes and demands. Until then, a complete can be quite the right choice.
The laws for skateboarding helmets vary from state to state. Many states require that skaters wear a helmet under a certain age, and some states like California make all skaters under 18 wear a CPSC Certified helmet at all times. CSPC skateboard helmets usually have an EPS protective liner that meets the safety standards for skateboarding. Make sure you check your state's regulations before ordering.
The grip tape found on a skateboard can actually be defined as the grainy sheet, which resembles sandpaper that also comes with a sticky underside. Such underside needs to adhere to the deck’s surfaces as a means of increasing traction or grip. No matter what skating style you use, the grip tape is extremely helpful in your attempt to stay on the board.
Ollie 180: an Ollie where the skateboarder and the skateboard spins 180 degrees after leaving the ground. Both the skateboarder and the skateboard rotate in the same direction (Frontside or Backside) with the skateboarder's feet sticking to the skateboard. This trick is usually referred to as a frontside or backside 180, or less frequently and more popular with older skateboarders and/or when performed on a bank/quarterpipe, a frontside / backside ollie
The longboard, a common variant of the skateboard, is used for higher speed and rough surface boarding, and they are much more expensive. "Old school" boards (those made in the 1970s–80s or modern boards that mimic their shape) are generally wider and often have only one kicktail. Variants of the 1970s often have little or no concavity, whereas 1980s models have deeper concavities and steeper kicktails.
Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
Slide your front foot as soon as you start jumping. Use the same movement you have been practicing to slide your foot towards the top end of the board, just as you jump off it and kick the back down. The front of your board should lift up as you slide your foot along it, with your foot hitting the top of the board at the highest point of your jump.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.
Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it.