If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
New shoes + new board + new grip tape isn’t going to help anything you need to reed what is above bro its an easy how to….bend down push your back foot down make sure the tail snaps off the ground and slid your front foot forward in one swift motion you’ll get it…iv been skating 11 years and its taken me this long to finally land kick flips regularly heel flips and varials my tres are 1 outa 10 still so I practice every day and someday ill be able to land it regularly when I want skateboarding takes alot of patients ALOT so dont think you’re going to learn everything over night just sayin
There are other types of ollies that you can do either alongside or combine with the ones listed above, like the tailgrab, indy grab, melon grab, stalefish, tweak, and dolphin nose. All of those skateboard tricks are performed more or less how they sound, but you might want to watch some videos on youtube to see a pro in action (as well as awesome cat videos).
The KPC Series Pro Skateboard measures 8.0” x 32”. This is a common width most often associated with pro skateboarders. Wider and stronger than the rookies, this model is the perfect size for someone who is better at skating and looking for an upgrade from the rookie models. The pro features a modern concave which allows for not only comfort, but more pop making it easier to learn tricks.
The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air.[2] While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.[citation needed]
When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.
It is a mini-cruiser, which is known for its strength as well as its ability to offer real value for the money you spent. This skateboard can also be expected to deliver an impressive performance – thanks to the Abec 7 skatro bearings used in it. There are also 59-mm urethane wheels and the 3-inch GOLD aluminum trucks that can help smoothen each ride.
New shoes + new board + new grip tape isn’t going to help anything you need to reed what is above bro its an easy how to….bend down push your back foot down make sure the tail snaps off the ground and slid your front foot forward in one swift motion you’ll get it…iv been skating 11 years and its taken me this long to finally land kick flips regularly heel flips and varials my tres are 1 outa 10 still so I practice every day and someday ill be able to land it regularly when I want skateboarding takes alot of patients ALOT so dont think you’re going to learn everything over night just sayin

Today, many riders use the “ollie-pop” on more than just the flat-level surfaces in between other tricks, it’s used heavily in the half-pipe and bowl ramps to allow the rider to go even higher in the air. Performing the “ollie-pop” while you’re at or near the top of the lip is a great way to get an extra couple feet, which might be all you need to get that extra turn in and nail the 720 (or 900, if you’re Tony Hawk).


As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
×