The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
Almost every skate shop will have a wall of boards that is either organized by brand, size, or alphabetically. At our CCS skate shop, we have multiple walls of boards that we try and keep ordered alphabetically. A wall of skateboards, at first glance, can be overwhelming, but if you know what size and roughly what brands you like, it should be fairly easy for you to figure out what board you want. Now would be a good time to mention our CCS Skateboard Buyer’s Guide, specifically the Decks Guide. In the CCS Decks Guide, you’ll find all the information you need to gain a basic understanding of skateboard decks.

No one had ever seen anything quite like it before, but no one knew just how transformative that moment would become. It wasn’t just that you could simply pop up into the air, it’s that it gave the rider a whole other set of opportunities to do tricks, and you don’t even have to be dependent on a ramp! As time went by, people began to add other skateboard tricks while they were airborne.

Invented in the late 1970s by Alan "Ollie" Gelfand, the ollie has become a skateboarding fundamental, the basis for many other more complicated tricks. In its simplest form, the ollie is a jumping technique that allows skaters to hop over obstacles and onto curbs, etc. What's so amazing about the ollie is the way the skateboard seems to stick to the skater's feet in midair. Seeing pictures of skaters performing soaring 4-foot ollies, many people assume that the board is somehow attached to the skater's feet. It's not. What's even more amazing about the ollie is that to get the skateboard to jump up, the skater pushes down on the board! The secret to this paradoxical maneuver is rotation around multiple axes. Let's take a closer look.
New Arrivals Clothing Dresses & Rompers Tops Sweaters Sweatshirts & Hoodies Jackets Jeans Pants Leggings Shorts Skirts Swim Intimates Bras Panties Bodysuits Intimate Accessories Shoes Sneakers Boots & Booties Sandals Flats Heels & Wedges Slippers Accessories Backpacks Bags & Wallets Hats & Beanies Jewelry Hair Accessories Sunglasses Socks Belts Watches Scarves Hydro Flask Beauty Hair Bath & Body Makeup Fragrance Sun Care Brushes & Tools Deals RSQ Jeans BOGO 50% Off Sweaters BOGO 50% Off Sweatshirts BOGO 50% Off Tops 4 for $25 Tees 2 for $20 Backpacks 30-50% Off Panties 5 for $16 Bralettes BOGO 50% Off Vogue Sunglasses 40% Off Sunglasses 50% Off Jewelry BOGO 50% Off Sunglasses 2 for $15 Trends COZY SHOP Riverdale Zipper Details Corduroy Color Trends Menswear Florals Stripes Checkered Button Front Tie Front Tie Dye & Crystal Wash Disney X Vans Converse X Hello Kitty Levi's X Mickey Only at Tillys
But there isnt a magic key or secret. Skateboarding is suprisingly a lot of brute force. That is, there is no magic secret, it’s practice practice practice. If you wanna learn any trick, keep trying that trick. There are of course proper techniques and improper, but theyre nigh impossible to describe effectively. it’s all about feel and a lot of tricks defy description.
Do your Ollie, then, instantly after you pop your board, lift your back foot up to meet your front foot. That helped me solo much I improved twice in a few tries with using that trick. And, if that doesn’t help, it’s just a matter of practicing. If you practice a ly every day, you experiment, you will find u r solution. But, try lifting u r back foot high right after u pop 😉

After that I went to my regular Olley spot to practice, fell so hard three times. My legs were so fucked up from the day before. Now I feel like shit because I had problem with a 20cm ledge I landed at least 100 times up and down yesterday. I’m even capable of 50cm ledges at slow speed, but I only get the front wheel and the board up so I have to put pressure on the nose to get it all the way up.


The KPC Series Pro Skateboard measures 8.0” x 32”. This is a common width most often associated with pro skateboarders. Wider and stronger than the rookies, this model is the perfect size for someone who is better at skating and looking for an upgrade from the rookie models. The pro features a modern concave which allows for not only comfort, but more pop making it easier to learn tricks.
Skateboarding is all about creativity and finding new challenges. A great way to explore skateboarding is to ride different shaped boards, wider trucks, and different size wheels. As you progress and start to ride new terrain and skate different kinds of spots, you may find one wheel size or board shape works better for you than another. There’s no wrong or right anything. There are no rules. Except for maybe one, and that is to keep skating. Skate as often as you can. Never is this more true than in the beginning while you’re developing your style and fundamentals.
But there isnt a magic key or secret. Skateboarding is suprisingly a lot of brute force. That is, there is no magic secret, it’s practice practice practice. If you wanna learn any trick, keep trying that trick. There are of course proper techniques and improper, but theyre nigh impossible to describe effectively. it’s all about feel and a lot of tricks defy description.

As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
Don’t get your hopes shot if it takes you a while to get this down.  Once you know how to ollie, beginner skateboarders you can do any trick in the book with just a little bit of practice.  Once you get this trick down while your stationary, go practice while moving around a little bit, try to hop off a couple of curbs.   You’ll be skateboarding like a pro in no time.  Just keep at it.

Choosing a skateboard deck can be approached in a few different ways: you can choose your board based off the graphic, the brand, the shape, the width, or even the color. For most skateboarders, it’s a combination of all these factors, but if you’ve never skateboarded before, you may not know what shape, width, or brand you like best. In this case, choosing your favorite graphic would make total sense.


It looks simple but yet complicated and vice versa. It takes most weeks to months to learn n some even years but a lifetime of effort to be consistent and be perfect at it and able to go higher, faster and further. It is not a feat you achieve once and it can be thrown out of the window if you want to continue to skate well. I've know skateboarders who just does ollies, boned ollies, ollie north and ollie souths, fakie ollies, switch ollies and nollies and nothing else but everytime he's popping them over 3ft height and up ledges, over gaps and down stair sets or over handrails. So no one's gonna argue on that even though he's not bustin some new fangled pressure flip late flip revert or something. He gets mad street creds for those huge ollies.
When I was about 10, I broke my first skateboard by riding it into a ditch. A decade later, in college, I broke another skateboard within an hour of owning it (surely a record) in a short-lived attempt at doing an ollie. (Surprisingly, the store accepted a return on that board even though it was in two pieces.) Then I was gifted a really nice, high-quality skateboard. The first thing I did with it was ride it down a big hill, a valiant but ill-fated adventure which ended with me jumping off the skateboard, rolling down the grass, and arriving scraped up, deflated, and rather disoriented near the entrance to my college cafeteria. (In my defense, the wheels and ball-bearings on that skateboard had been pre-lubricated to minimize friction, and why would anyone do that, that's just crazy.)
Punisher Skateboards Warphant measures 31 x 7.5 inch.  It has a 9-Ply Maple Black Board with Concave Deck and Double Kick Tail.  It comes with ABEC-3 Bearings, 5-inch V-style Heavy Duty Alloy Trucks, and Bases.  It uses 54 x 36 mm PU injection molded wheels and PE Riser Pad with PU Cushion and Punisher Logo.  It is perfect for learning and doing tricks.  It is best suited for riders who are 8 years old and above.  It has a 5 rating on Amazon.

The Rimable Complete 22″ Skateboard is the most compact street board that are ready-to-use.  It is best for exercise and fun, and very portable.  There are five colors that you can choose from Black, Blue, White, Purple, and Green.  It has high-quality construction, with a high-density plastic deck.  It features extremely smooth 59mm wheels along with ABEC7 bearings and solid aluminum trucks.  It measures 22″ long and 6″ wide and weighs 4 pounds.  It has the best rating of 4.3 on Amazon.


4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve
Skateboarding is all about creativity and finding new challenges. A great way to explore skateboarding is to ride different shaped boards, wider trucks, and different size wheels. As you progress and start to ride new terrain and skate different kinds of spots, you may find one wheel size or board shape works better for you than another. There’s no wrong or right anything. There are no rules. Except for maybe one, and that is to keep skating. Skate as often as you can. Never is this more true than in the beginning while you’re developing your style and fundamentals.
The switch stance ollie uses a similar body motion, but the nollie is subtly distinct: For one, the rider is always moving forward, with the body positioned in a nollie stance--closer to the nose and with the front foot on the nose. Secondly the rider usually postures the body differently so as to compensate for this stance with respect to the forward motion. The rider presses the nose down using their front foot to engage the "pop" motion in order for the board to rise. This is In contrast to a "Fakie Ollie" where the pop motion is performed by the rear foot on the tail, similarly to a normal Ollie, however the rider is traveling backwards when performing a Fakie Ollie. Where in a Nollie the rider is traveling forward with their front foot on the nose to apply the initial force "pop".
To summarize, a skateboarder's feet need to do two things successfully to complete an ollie. They need to provide a changing force to move the board correctly (so that the combined force of gravity and the skater's feet add up to the green arrows above), and they need to provide different amounts of force with each foot (shown by the red and blue arrows above) to steer and turn the board into the right orientation.
So the proper foot placement for the ollie is with the ball of your back foot horizontal on the tail of your skateboard.  And your front foot centered on your board right behind the front trucks.  You may find that moving your feet around in different positions are more comfortable.  This is fine,  everybody can learn how to skateboard their own way.
Im a girl too. And here’s the deal. Guys wont bring you down unless you make a big deal out of being a girl at a skatepark. Go to a skatepark, skate until you want to stop, rock it, and stay confident. Guys could not care less whether or not you’re a girl who skates, and thats the bottom line. You just gotta learn to ollie perfectly and you’ll get to the point where you’ll be making their confidence falter.
Rails (or ribs), are narrow strips of plastic or metal that are attached under the deck lengthwise along the edges. They are used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Rails also provide a more consistent feel for slides, as the slide of a regular skateboard will suffer from the wear of the paint or varnish on the bottom of the board. Although rarely used anymore, they are useful for experienced skaters that are capable of grabs.
Both your height and weight should play an important role when you are choosing a skateboard. You need to find a skateboard, which fits your weight and height. Picking one, which is either too small or too big might only cause you to experience difficulty controlling it, especially if you are still a beginner learning the ins and outs of skateboarding.
From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.
Punisher Skateboards Warphant measures 31 x 7.5 inch.  It has a 9-Ply Maple Black Board with Concave Deck and Double Kick Tail.  It comes with ABEC-3 Bearings, 5-inch V-style Heavy Duty Alloy Trucks, and Bases.  It uses 54 x 36 mm PU injection molded wheels and PE Riser Pad with PU Cushion and Punisher Logo.  It is perfect for learning and doing tricks.  It is best suited for riders who are 8 years old and above.  It has a 5 rating on Amazon.
If you are looking to buy a pre-built complete for yourself or someone else, CCS has pre-built complete skateboards for sale, too. This is by far the fastest way to buy a skateboard complete and often times the least expensive. Because we work directly with the manufacturer's, the cheapest skateboard complete for sale is our CCS Logo Skateboard Complete.

Large power is created at the point of action by applying small power to the point of effort. Application of this concept to skateboarding makes the back wheels the fulcrum, the tail the point of effort, and the nose the point of action. Applying power to the tail causes the nose to shoot upwards. When the front foot of the skater levels the nose at a point roughly horizontal to the ground in anticipation of the tail, soon to be leveled likewise by the skater’s back foot, the process smoothly done creates the illusion of the skateboard ‘sticking’ to the feet.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Choosing a skateboard deck is a great place to start when building a complete skateboard. Unless you have experience riding a shaped board - something a little more retro or unusual, we recommend you start with a popsicle shape. CCS carries over 60 different skateboard deck brands that sell this popular popsicle shape. If you have questions on what size you should ride or have any other questions about building a complete, we recommend you check out our Skateboard Buyer’s Guide. Here, you’ll find helpful how-to’s for choosing a skateboard decks, skateboard trucks, skateboard wheels, skateboard bearings, and skateboard components. This guide explains every part of a skateboard and helps you choose which sizes and styles to best suit your needs.

When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.

The Landwalker 22″ Complete Skateboard has a sturdy 7 layer Canadian maple deck. It’s best for downhill, U table and slider because of its enormous stability. This board is best for teens and adults. It comes with Abec 7″ Bearings, PU wheels, Black Grip Tape, and hardware. It measures 79 x 20 x 10 cm. This board is an awesome gift for Christmas or Halloween.
If you love skateboarding, then it is a must for you to invest in a high-quality backpack or bag. It is an essential gear, especially if you are someone on the go. You need it as it lets you bring all the things and items you need while you are riding to work or school – that’s possible while still ensuring that you bring your board with you all the time.
Skateboarding is a very individual activity. There is no right or wrong way to skate. Skateboarding still hasn't stopped evolving, and skaters are coming up with new tricks all the time. Skateboarding has gone through its ups and downs over the years. However, since 2000, due to attention in the media and products like skateboarding video games, children's skateboards and commercialization, skateboarding has been pulled into the mainstream. As more interest and money has been invested into skateboarding, more skate parks, better skateboards have become available. In addition, the continuing interest has motivated skateboarding companies have to keep innovating and inventing new things. In 2020 Skateboarding will appear for the first-time in the Olympics in Tokyo, Japan.[4]
The laws for skateboarding helmets vary from state to state. Many states require that skaters wear a helmet under a certain age, and some states like California make all skaters under 18 wear a CPSC Certified helmet at all times. CSPC skateboard helmets usually have an EPS protective liner that meets the safety standards for skateboarding. Make sure you check your state's regulations before ordering.

Hey, I’m a girl too and I’ve been skateboarding for nearly ten years now. I’m not a pro or anything, but I used to ride around in the local skatepark that was mainly just a big bowl that was fun to just drop into and cruise around in. I’m only just now learning street tricks. Anyways, I’d go there and the dudes would sometimes tease me, but sometimes they’d tease me about it. The thing you gotta do is not give up. Just ignore them. Dudes are stupid. Practice at home, by yourself, and learn some awesome stuff. So when you get really good, you can go to the park and if they start saying bad stuff, show off. It’ll blow them away. It always made me feel really good to show them that I was better than them right after they teased me for it.
Hey, I’m a girl too and I’ve been skateboarding for nearly ten years now. I’m not a pro or anything, but I used to ride around in the local skatepark that was mainly just a big bowl that was fun to just drop into and cruise around in. I’m only just now learning street tricks. Anyways, I’d go there and the dudes would sometimes tease me, but sometimes they’d tease me about it. The thing you gotta do is not give up. Just ignore them. Dudes are stupid. Practice at home, by yourself, and learn some awesome stuff. So when you get really good, you can go to the park and if they start saying bad stuff, show off. It’ll blow them away. It always made me feel really good to show them that I was better than them right after they teased me for it.
I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
Mounting hardware is a set of eight 10-32 UNF bolts, usually an Allen or Phillips head, and matching nylon locknuts. They are used to attach the trucks (and any type of risers) to the board. Some sets have one different colored bolt to show which side is the nose of the skateboard. Hardware is available in various lengths for mounting trucks with or without risers.

The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
If you love skateboarding, then it is a must for you to invest in a high-quality backpack or bag. It is an essential gear, especially if you are someone on the go. You need it as it lets you bring all the things and items you need while you are riding to work or school – that’s possible while still ensuring that you bring your board with you all the time.

Made with bamboo and fiberglass, this board is tough, flexible and ready for anything. The construction is designed to feel and act like a snowboard. The drop-through design is perfect for freestyle longboarding, commuting, carving, pumping and more. It gives you better stability and more wheel clearance. The board is definitely best designed for carving but tricks and kicks are easily done as well.
When looking at skateboarding’s history, the only thing that’s stayed the same is the overall structure: every board consists of four skateboard wheels, two skateboard trucks, and a riding surface of some kind. And while we’ve come a long way from the days of metal and clay wheels, some aspects of skateboarding - like the brands manufacturing some of the most trusted products - haven’t changed at all. Independent Trucks has been designing trucks since 1978. Powell Peralta, the company responsible for Powell Skateboards, Bones Wheels, Bones Bearings, and the Bones Brigade also started in 1978. NHS, Inc., the company that produces Santa Cruz Skateboards, Independent Trucks, Bronson Speed Bearings, Krux trucks, Flip Skateboards, Ricta Wheels, Mob Grip, and OJ Wheels started in 1973. It’s no wonder these brands are still doing so well - they’ve been with skateboarding since the beginning. Since the day skateboarding went from something surfers did when the waves were flat to its own sport that involves technique, practice, and careful consideration, a small handful companies have been there to help skateboarding become what it is today.

It's a neat piece of science art, and it also tells us something interesting. The arrows show us that the force on the skateboard is constantly changing, both in magnitude as well as in direction. Now the force of gravity obviously isn't changing, so the reason that these force arrows are shrinking and growing and tumbling around is that the skater is changing how their feet pushes and pulls against the board. By applying a variable force that changes both in strength and direction, they're steering the board.
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.
Large power is created at the point of action by applying small power to the point of effort. Application of this concept to skateboarding makes the back wheels the fulcrum, the tail the point of effort, and the nose the point of action. Applying power to the tail causes the nose to shoot upwards. When the front foot of the skater levels the nose at a point roughly horizontal to the ground in anticipation of the tail, soon to be leveled likewise by the skater’s back foot, the process smoothly done creates the illusion of the skateboard ‘sticking’ to the feet.

Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
There is no governing body that declares any regulations on what constitutes a skateboard or the parts from which it is assembled. Historically, the skateboard has conformed both to contemporary trends and to the ever-evolving array of stunts performed by riders/users, who require a certain functionality from the board. The board shape depends largely upon its desired function. Longboards are a type of skateboard with a longer wheelbase and larger, softer wheels.
Ride like the pros with Tony Hawk skateboards, Airwalk skateboards and boards from Razor�, Kryptonics, Maple� and other trusted brands. These high-quality skateboards utilize smooth-rolling trucks and ball bearings that prevent jams and freezing as you shoot through the half-pipe or roll down the sidewalk. And while performance is your top consideration, all your tricks and moves will look even cooler with a board that's splashed with bright colors, emblazoned with attention-getting graphics and made with a sleek design. Choose from styles with bold patterns and detailed, full-color artwork that showcase your personal aesthetic along with your athleticism.
The grip tape found on a skateboard can actually be defined as the grainy sheet, which resembles sandpaper that also comes with a sticky underside. Such underside needs to adhere to the deck’s surfaces as a means of increasing traction or grip. No matter what skating style you use, the grip tape is extremely helpful in your attempt to stay on the board.

Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
×