Since its humble beginnings, Element was created out of passion and an unwavering dedication to making a positive difference. The tree continues to grow while it respects its deepest roots and embraces the landscape of skateboarding, and the lifestyle that surrounds it. From team riders to advocates, and product to marketing, Element is all inclusive, whose mission is to lead not follow, and leave an imprint deep enough, that it continues to make the world a better place.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.
Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
Made with bamboo and fiberglass, this board is tough, flexible and ready for anything. The construction is designed to feel and act like a snowboard. The drop-through design is perfect for freestyle longboarding, commuting, carving, pumping and more. It gives you better stability and more wheel clearance. The board is definitely best designed for carving but tricks and kicks are easily done as well.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
Almost every skate shop will have a wall of boards that is either organized by brand, size, or alphabetically. At our CCS skate shop, we have multiple walls of boards that we try and keep ordered alphabetically. A wall of skateboards, at first glance, can be overwhelming, but if you know what size and roughly what brands you like, it should be fairly easy for you to figure out what board you want. Now would be a good time to mention our CCS Skateboard Buyer’s Guide, specifically the Decks Guide. In the CCS Decks Guide, you’ll find all the information you need to gain a basic understanding of skateboard decks.
Learning to skateboard takes dedication. If you want to learn fast, it helps if you have an order and a strategy. Many new skateboarders try to learn to Ollie or learn to kickfliip before they are ready. They will try to Ollie before they can effectively push their skateboard or even do a kickturn. This often leads to frustration and even giving up. So, for you parents and Noobs out there, here is an outline of some of the very first things you should learn to do on a skateboard.
Hi, I can do an Ollie for 1 month already but somehow my Ollie is always unbalanced, meaning the front nose pops much higher than the back wheel. I understand that this is due to my front foot not sliding up higher, but I’m not sure how to correct it because my foot seem to get stuck after sliding up about an inch. Is it because of wrong technique or lack of calf muscles?
The grip tape found on a skateboard can actually be defined as the grainy sheet, which resembles sandpaper that also comes with a sticky underside. Such underside needs to adhere to the deck’s surfaces as a means of increasing traction or grip. No matter what skating style you use, the grip tape is extremely helpful in your attempt to stay on the board.
No one had ever seen anything quite like it before, but no one knew just how transformative that moment would become. It wasn’t just that you could simply pop up into the air, it’s that it gave the rider a whole other set of opportunities to do tricks, and you don’t even have to be dependent on a ramp! As time went by, people began to add other skateboard tricks while they were airborne.
Low ollies: This can happen for a lot of reasons, but the biggest one is that you are not crouching low enough before your ollie, and not pulling your feet high enough after you jump. When you crouch down, try and touch the ground. When you jump, try to hit yourself in the chest with your knees. Both knees. Don’t worry about falling. That will happen sometimes – that’s just part of skateboarding! For more help, read the How Can I Make My Ollies Higher? FAQ
My problem is Everytime I try to pop the back it’s not hard enough and I get no air. The article says to jump up so I do it physically and sometimes it seems to help. But when I watch skate videos and other skaters It doesn’t appear they are actually jumping up. They just seem to be popping the board. So should I physically jump? May sound stupid but it’s something I struggle with.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
Unlike golf or tennis, skateboarding is a sport where there isn’t a difference between the equipment needed for men and women to compete together. Women skate, flip and bruise just like the guys they’re at the skatepark with. The only consideration women may want to account for is that people who are shorter or smaller often want a shorter board for optimal control. The DAPANLA Skateboard Deck is a great deck that is slightly smaller, but can do it all.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
In most cases, it is available in black but you can also find clear ones that are ideal for you if you want to show a specific logo. Another nice choice that you have is the die-cut grip tape, which works in displaying the color or design of the deck beneath it. Make sure to choose a grip tape at a size, which perfectly suits your skateboard’s deck.
The Moose Blank Skateboard deck is a made with a 7-ply composition and features Canadian Maple wood. The board is 8.25 inches in length, but Moose Blank offers shorter boards as well, fitting men and women of just about any size and skill. The deck itself has a modern concave, making turning a breeze for beginners and pros. The nose and tail are particularly steep for tricks - “perfect for shredding,” says Blank Moose. Although this board is 100 percent blank, Moose Blank offers stains and dips for monochromic board designs as well. There are also Moose Blank sets for sale, which provide a set of blank decks at a discount.
Ollie 180: an Ollie where the skateboarder and the skateboard spins 180 degrees after leaving the ground. Both the skateboarder and the skateboard rotate in the same direction (Frontside or Backside) with the skateboarder's feet sticking to the skateboard. This trick is usually referred to as a frontside or backside 180, or less frequently and more popular with older skateboarders and/or when performed on a bank/quarterpipe, a frontside / backside ollie
Bought for my 7yo's first real board, and for the price its perfect. Beginners look no further! Sure the trucks, bearings, and wheels are my choice, but as someone whose ridden for 20+ years, guarantee these items are way above Walmart status and are more than capable for you shred park or street. Bonus that it came no put together, can teach the little clone how to put it all together.
If you’ve ever watched a skateboarder roll down the street and then all of a sudden pop into the air on a skateboard, you’re probably wondering the same question a lot of people do: how on earth do they do that? It almost seems magical how they just seem to explode off the ground, and then just kind of float. Skateboarder, meet, the ollie. It’s not in the category of “easy skateboard tricks,” but if you learn how to ollie, you’re well on your way to fame and fortune as a professional skater.
Taotao Girls Skateboards comply to United State Consumer Product Safety Commission (CPSC) Standard. It has a 24″ X 6″ Maple Double Kickside Deck. It features 608Z Bearings, 3.5″ Plastic Truck & Base, and 50 x 30 mm PVC Wheels. The Safety helmet, Knee and Elbow Pads also comply to CPSC Standard. It has a Cool Pink Aloha Graphic Design with an Amazon rating of 4.3.
Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
You can learn to ollie while standing stationary, or while your skateboard is rolling. Ollying while standing still works the same way as while rolling, but I think rolling ollies are easier than stationary ollies. If you would like to learn to ollie with your skateboard stationary, you can place your skateboard on some carpet or grass to keep it from rolling. If you prefer to learn to ollie while your skateboard is rolling, don’t go very fast at the start. Whichever way you learn to ollie, once you feel comfortable you should try to ollie the other way as well.