Hey guys. I’m a girl and I am having some trouble with my ollie. I know the steps in order to do an ollie, but I can’t seem to do all of them. I can do a perfect pop on the back foot, but my problem lies in my front foot. (I am regular footed but idk if that matters) I know I just need to get my back wheels off the ground, but when I try to slide it, my foot just stays frozen. I try really hard to make it move, and when it does it just goes straight across, skimming the bottom of my shoes. Even then I can only move it half an inch. I have pretty mild griptape, that might change something? Idk.
In 1977, skate parks began cropping up all over the place, including Skateboard USA, where Gelfand began to spend most of his time. His buddy, Scott Goodman, is the one who gave Gelfand the nickname of “Ollie” and dubbed his aerial lipside the “ollie-pop.” Pictures of Gelfand during this time period clearly show him getting airborne and performing the trick associated with his name today.
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
It is mainly because those items are guaranteed to help you familiarize yourself with the ins and outs of using them. They are a big help in making you feel comfortable when you push off with your feet while also balancing on top of the board when riding. It is not good to go for a very technical product, so it’s best to choose the mentioned types first.
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.

Do your Ollie, then, instantly after you pop your board, lift your back foot up to meet your front foot. That helped me solo much I improved twice in a few tries with using that trick. And, if that doesn’t help, it’s just a matter of practicing. If you practice a ly every day, you experiment, you will find u r solution. But, try lifting u r back foot high right after u pop 😉

The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
×