The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
The Skatro Mini Cruiser Skateboard includes Abec 7 Skatro Bearings, 59MM Urethane Skatro wheels, and 3-inch lightweight aluminum trucks.  The Skatro Flexy Technology ensures optimal flex on every board. Skatro outperforms most of the leading brands and it has an amazing value.  You can take this board on the subway, plane, train, and even on the bus.  It includes a color matching T-tool.  It has the best rating of 4.8 on Amazon.
Since its humble beginnings, Element was created out of passion and an unwavering dedication to making a positive difference. The tree continues to grow while it respects its deepest roots and embraces the landscape of skateboarding, and the lifestyle that surrounds it. From team riders to advocates, and product to marketing, Element is all inclusive, whose mission is to lead not follow, and leave an imprint deep enough, that it continues to make the world a better place.
Skateboarding is the best and worst thing that’ll you’ll ever have the pleasure of tearing your hair out over. In a typical day of skating, you’ll get hurt, you’ll get incredibly frustrated, and eventually land a trick that’ll make it all worth it - if you’re lucky. Choosing a skateboard is fairly simple if you know what shape and width you like. If you’ve been skating awhile, you’re probably fairly familiar with what board brands you like skating. If not, there are a number of resources to help you choose the best skateboard for your skating style. Continuing to read this little spiel is going to take the least amount of effort on your part.
Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
The Bamboo Skateboards Galaxy Series Cosmic Cloud Skateboard Deck is an excellent option. This concave board is made exclusively of a bamboo hybrid, rather than pure maple. This means the deck is lighter, stronger, more flexible and can even absorb shock better. The non-carbonized, light-wood deck is made of 6-ply wood and is in its fourth generation of designs.

Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.


The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.

Today, many riders use the “ollie-pop” on more than just the flat-level surfaces in between other tricks, it’s used heavily in the half-pipe and bowl ramps to allow the rider to go even higher in the air. Performing the “ollie-pop” while you’re at or near the top of the lip is a great way to get an extra couple feet, which might be all you need to get that extra turn in and nail the 720 (or 900, if you’re Tony Hawk).
Level out on the way down – Before you start to head back towards the safety of the earth, level your feet out as the board begins to fall. If you’re trying to jump a gap on your board, this will help you keep going straight and maintain your momentum. Alternatively, you can land on your nose or tail and perform a manual out of the jump, but those are pretty advanced moves. Might want to wait until those little pink training wheels are off your board first.
The DAPANLA deck is 7.5-by-31-inches in size, on the smaller side of good quality, real skateboard decks, which makes it ideal for smaller and shorter people. Unlike many decks on the market today, the DAPANLA deck comes with non-slip grip tape on the top. The underside of the deck is similarly decorated, with a range of DAPANLA designs including the fun cartoon avocado board that is sure to turn a few heads for its uniqueness. 
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
Grip tape is a sheet of paper or fabric with adhesive on one side and a surface similar to fine sandpaper on the other. Grip tape is applied to the top surface of a board to allow the rider's feet to grip the surface and help the skater stay on the board while doing tricks. Grip tape is usually black, but is also available in many different colors such as pink, red, yellow, checkered, camo, and even clear. Often, they have designs die-cut to show the color of the board, or to display the board's company logo. Grip tape accumulates dirt and other substances that will inhibit grip, so use of a grip eraser or rubber eraser is necessary after riding through mud or with dirty shoes.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
The skateboard has a solid and stiff mini-deck, which is around 22 inches and constructed out of 100% plastic material. Such deck is very lightweight. It is only four pounds but you have an assurance that it can handle up to 198 lbs. of weight. You will also fall in love with the board as it comes in 23 graphics and colors, so picking a favorite is much easier.
Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.
Maybe you're new to skateboarding. We have lots of complete skateboards or longboards to get you started. All of our skateboard and longboard completes come fully assembled, so you can hit the streets without any of the hassle—try an Enjoi skateboard complete or check out our selection of Sector 9 longboard and skateboard completes. Or maybe you're an experienced skater looking to update and customize your ride. You probably want to start with the perfect skateboard deck before you do anything else. We carry high-quality skate decks to keep you steady and balanced while you bomb, slide, and carve the streets. We also have a variety of longboard decks in stock if you're looking for a smooth ride for cruising or commuting.

Learning to skateboard takes dedication.   If you want to learn fast, it helps if you have an order and a strategy.   Many new skateboarders try to learn to Ollie or learn to kickfliip before they are ready.  They will try to Ollie before they can effectively push their skateboard or even do a kickturn.   This often leads to frustration and even giving up.   So, for you parents and Noobs out there, here is an outline of some of the very first things you should learn to do on a skateboard.
This board includes professional assembly. All Krown skateboards arrived assembled and ready to ride straight out the box. The Rookie model includes heavy duty Aluminum 5.0 trucks, 52mm 99A high-rebound urethane wheels, precision speed Abec 7 bearings, high tensile phillips head mounting hardware, and 80 grit black grip tape. Each component meets the industry standards and are a common choice of skaters worldwide.
Here we have an original Z Jimmy Plumer model. It has some handling scuffing from being around for several decades, but displays great. Grip has no holes at trucks which leads me to believe it’s never had any mounted. This is one heavy fiberglass mamma jamma. Get this piece of history at a fair price. I will throw in free priority insured shipping for the con us. Everywhere else at actual cost. Thanks for looking.
Skateboarding Trick Tip: How To Ollie The Easiest Way & Common Ollie Problems,How to ollie on a skateboard,how to ollie on a skateboard,how to ollie higher,how to ollie while moving,how to ollie on a skateboard for beginners,how to ollie while moving for beginners,how to ollie stairs,skateboarding tricks,skateboarding ollie tutorial,skateboarding ollie slow motion,how to ollie up a curb,how to ollie while moving,overindulgingSkateboarding Trick Tip: How To Ollie The Easiest Way & Common Ollie Problems
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
Don’t get your hopes shot if it takes you a while to get this down.  Once you know how to ollie, beginner skateboarders you can do any trick in the book with just a little bit of practice.  Once you get this trick down while your stationary, go practice while moving around a little bit, try to hop off a couple of curbs.   You’ll be skateboarding like a pro in no time.  Just keep at it.

The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.

As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
×