Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
When I was about 10, I broke my first skateboard by riding it into a ditch. A decade later, in college, I broke another skateboard within an hour of owning it (surely a record) in a short-lived attempt at doing an ollie. (Surprisingly, the store accepted a return on that board even though it was in two pieces.) Then I was gifted a really nice, high-quality skateboard. The first thing I did with it was ride it down a big hill, a valiant but ill-fated adventure which ended with me jumping off the skateboard, rolling down the grass, and arriving scraped up, deflated, and rather disoriented near the entrance to my college cafeteria. (In my defense, the wheels and ball-bearings on that skateboard had been pre-lubricated to minimize friction, and why would anyone do that, that's just crazy.)
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!
The deck is expertly constructed with a vertically laminated bamboo core and bamboo veneer exterior, all attached with triaxial glass and epoxy as well as a course grip tape top. The grip tape is arranged in an unusual and stylish, yet functional design. The 34-inch board features a 13-degree nose angle and a 18-degree tail angle. With its directional shape, you’ll easily be able to cruise on this board or pull a few tricks. It is a lightweight and flexible deck.
One foot on the tail, (by foot I mean the ball of the foot which is just behind the big toe) the other foot is about an inch behind the bolts(screws) for the front truck. Basically, the back foot quickly pushes the tail down, and right when the tail of the board strikes the ground, the back foot jumps up… the tail of the board will follow up with the foot when the front foot slides forward slightly, which pivots the tail of the board upwards. Since the front truck comes off the ground first, getting the back truck up is the trick.

Regardless of your skill level, you definitely need quality skateboard parts and that begins with skateboard trucks. We carry hundreds of top-selling skate trucks! Hardcore skateboarders love our Independent skate trucks for their performance and durability. You can also pick out the perfect skateboard wheels, like a blazing fast set of Spitfires, and you'll be one step closer to skating like a pro. To make the most of your skate wheels, you'll need quality skate bearings, too—check out top-seller Bones Bearings. When building a skateboard, even the smallest choices make a difference, so be sure to get the right size skate hardware, double-check your skateboard bushings, and don't forget to grit up your board with grip tape.
With Enkeeo 22 Inch Cruiser Skateboards, you can cruise in style.  It has a dimension of 22 x 6 inches.  It comes with 3″ Black Coated Habitat trucks, Black 60mm Smooth wheels, and Abec11 bearings. It’s ready to ride and you can even personalize the tail of the board for free with a limitation of 10 Characters only. It has 30 days warranty and is manufactured in California.  It has a perfect 5 rating on Amazon.

The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.


Unlike golf or tennis, skateboarding is a sport where there isn’t a difference between the equipment needed for men and women to compete together. Women skate, flip and bruise just like the guys they’re at the skatepark with. The only consideration women may want to account for is that people who are shorter or smaller often want a shorter board for optimal control. The DAPANLA Skateboard Deck is a great deck that is slightly smaller, but can do it all.  
EXPERIENCED SKATER! This board is amazing for the price! (notice i said FOR THE PRICE) At the time of this review, the board was $44.40 and for that price the board i got was phenomenal. It is a 7-ply deck with aluminum trucks (havent figured out the bearings but they definitely feel like the abec 5 they claim to be). The trucks arent the best quality out there and the board can be a little thinner (maybe 5-ply) but the overall board is amazing. There are only two complaints. The hole in the wheels is a tiny TINY TIIINYYY bit off center, but nothing that cant be fixed with a new set. I can see what another review said by it not coming assembled, as a couple of the bolts on the wheels are a little loose, but the board does come assembled.
The switch stance ollie uses a similar body motion, but the nollie is subtly distinct: For one, the rider is always moving forward, with the body positioned in a nollie stance--closer to the nose and with the front foot on the nose. Secondly the rider usually postures the body differently so as to compensate for this stance with respect to the forward motion. The rider presses the nose down using their front foot to engage the "pop" motion in order for the board to rise. This is In contrast to a "Fakie Ollie" where the pop motion is performed by the rear foot on the tail, similarly to a normal Ollie, however the rider is traveling backwards when performing a Fakie Ollie. Where in a Nollie the rider is traveling forward with their front foot on the nose to apply the initial force "pop".
New Arrivals Clothing Dresses & Rompers Tops Sweaters Sweatshirts & Hoodies Jackets Jeans Pants Leggings Shorts Skirts Swim Intimates Bras Panties Bodysuits Intimate Accessories Shoes Sneakers Boots & Booties Sandals Flats Heels & Wedges Slippers Accessories Backpacks Bags & Wallets Hats & Beanies Jewelry Hair Accessories Sunglasses Socks Belts Watches Scarves Hydro Flask Beauty Hair Bath & Body Makeup Fragrance Sun Care Brushes & Tools Deals RSQ Jeans BOGO 50% Off Sweaters BOGO 50% Off Sweatshirts BOGO 50% Off Tops 4 for $25 Tees 2 for $20 Backpacks 30-50% Off Panties 5 for $16 Bralettes BOGO 50% Off Vogue Sunglasses 40% Off Sunglasses 50% Off Jewelry BOGO 50% Off Sunglasses 2 for $15 Trends COZY SHOP Riverdale Zipper Details Corduroy Color Trends Menswear Florals Stripes Checkered Button Front Tie Front Tie Dye & Crystal Wash Disney X Vans Converse X Hello Kitty Levi's X Mickey Only at Tillys
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve

The DreadXBoards Concave Skateboard has Plastic Deck Injection Molded for excellent durability. It features Urethane Wheels 59mm 78a, aluminum trucks, and Abec 7 Bearings. It is completely assembled and is ready to ride. It is perfect for beginners or experienced riders. It can load up to 185 lbs. It is great for kids and adults. It has an excellent rating of 4 on Amazon.
Jump – Ah yes, finally, we have reached the move itself. Basically, you have to do about twelve different things all at once to execute a successful ollie-pop: lift your front foot, press down with your back foot, angle your front ankle,  and jump. Lift the front foot off the ground first, and then move your back foot. This whole process is easier if you’re actually moving forward – since you don’t have to fight for balance – but it can be done while you’re standing still as well.

Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
I found that my problem was unclear instruction about the timing between jumping and popping. One day when I was watching a slowmo ollie video though, I noticed that the skateboarder already was beginning to jump (at least his body was already going in an upward motion) before snapping the board off the ground. That was a critical change I needed to make in order to get it working. I had been trying to pop the board while all my weight was still pushing down on it (kind of an obvious mistake, but I somehow overlooked this). Hope this helps somebody.

!function(e){function n(t){if(r[t])return r[t].exports;var i=r[t]={i:t,l:!1,exports:{}};return e[t].call(i.exports,i,i.exports,n),i.l=!0,i.exports}var t=window.webpackJsonp;window.webpackJsonp=function(n,r,o){for(var s,a,l=0,u=[];l1)for(var t=1;td)return!1;if(p>f)return!1;var e=window.require.hasModule("shared/browser")&&window.require("shared/browser");return!e||!e.opera}function a(){var e="";return window.Q.sendErrorsToWeblogger&&"quora.com"==window.Q.subdomainSuffix&&(e+=[window.location.protocol,"//log.quora.com"].join("")),e+="/ajax/log_errors_3RD_PARTY_POST"}function l(){var e=o(h);h=[],0!==e.length&&c(a(),{errors:JSON.stringify(e)})}var u=t("./third_party/tracekit.js"),c=t("./shared/basicrpc.js").rpc;u.remoteFetching=!1,u.collectWindowErrors=!0,u.report.subscribe(r);var f=10,d=window.Q&&window.Q.errorSamplingRate||1,h=[],p=0,m=i(l,1e3),w=window.console&&!(window.NODE_JS&&window.UNIT_TEST);n.report=function(e){try{w&&console.error(e.stack||e),u.report(e)}catch(e){}};var y=function(e,n,t){r({name:n,message:t,source:e,stack:u.computeStackTrace.ofCaller().stack||[]}),w&&console.error(t)};n.logJsError=y.bind(null,"js"),n.logMobileJsError=y.bind(null,"mobile_js")},"./shared/globals.js":function(e,n,t){var r=t("./shared/links.js");(window.Q=window.Q||{}).openUrl=function(e,n){var t=e.href;return r.linkClicked(t,n),window.open(t).opener=null,!1}},"./shared/links.js":function(e,n){var t=[];n.onLinkClick=function(e){t.push(e)},n.linkClicked=function(e,n){for(var r=0;r>>0;if("function"!=typeof e)throw new TypeError;for(arguments.length>1&&(t=n),r=0;r>>0,r=arguments.length>=2?arguments[1]:void 0,i=0;i>>0;if(0===i)return-1;var o=+n||0;if(Math.abs(o)===Infinity&&(o=0),o>=i)return-1;for(t=Math.max(o>=0?o:i-Math.abs(o),0);t>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=0;r>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=new Array(s),i=0;i>>0;if("function"!=typeof e)throw new TypeError;for(var r=[],i=arguments.length>=2?arguments[1]:void 0,o=0;o>>0,i=0;if(2==arguments.length)n=arguments[1];else{for(;i=r)throw new TypeError("Reduce of empty array with no initial value");n=t[i++]}for(;i>>0;if(0===i)return-1;for(n=i-1,arguments.length>1&&(n=Number(arguments[1]),n!=n?n=0:0!==n&&n!=1/0&&n!=-1/0&&(n=(n>0||-1)*Math.floor(Math.abs(n)))),t=n>=0?Math.min(n,i-1):i-Math.abs(n);t>=0;t--)if(t in r&&r[t]===e)return t;return-1};t(Array.prototype,"lastIndexOf",c)}if(!Array.prototype.includes){var f=function(e){"use strict";if(null==this)throw new TypeError("Array.prototype.includes called on null or undefined");var n=Object(this),t=parseInt(n.length,10)||0;if(0===t)return!1;var r,i=parseInt(arguments[1],10)||0;i>=0?r=i:(r=t+i)<0&&(r=0);for(var o;r

×