Ollie 180: an Ollie where the skateboarder and the skateboard spins 180 degrees after leaving the ground. Both the skateboarder and the skateboard rotate in the same direction (Frontside or Backside) with the skateboarder's feet sticking to the skateboard. This trick is usually referred to as a frontside or backside 180, or less frequently and more popular with older skateboarders and/or when performed on a bank/quarterpipe, a frontside / backside ollie

Maybe you're new to skateboarding. We have lots of complete skateboards or longboards to get you started. All of our skateboard and longboard completes come fully assembled, so you can hit the streets without any of the hassle—try an Enjoi skateboard complete or check out our selection of Sector 9 longboard and skateboard completes. Or maybe you're an experienced skater looking to update and customize your ride. You probably want to start with the perfect skateboard deck before you do anything else. We carry high-quality skate decks to keep you steady and balanced while you bomb, slide, and carve the streets. We also have a variety of longboard decks in stock if you're looking for a smooth ride for cruising or commuting.
Almost is proud to announce a collaboration with Skateistan, the award-winning non-profit organization empowering children and youth through skateboarding and education. They recently launched a new Skate School in Phnom Penh, Cambodia on Friday (February 23rd, 2018). Over 100 children celebrated alongside special guests from around the world, including Almost flow skater Sky Brown. 
Mounting hardware is a set of eight 10-32 UNF bolts, usually an Allen or Phillips head, and matching nylon locknuts. They are used to attach the trucks (and any type of risers) to the board. Some sets have one different colored bolt to show which side is the nose of the skateboard. Hardware is available in various lengths for mounting trucks with or without risers.
The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.

My problem is that my board always lands crooked when I Ollie. The worst thing is that I even tell myself to “keep your shoulders straight” while I’m doing the Ollie and I still land crooked. I think it’s just hard for people to grasp the simple fact that everything on a skateboard has to be done horizontally which is odd because people don’t walk sideways. We walk straight. Like roller blading for example…. it’s easier for me to roller blade because I’m used to walking and running obviously except with a skateboard everything is as if you were hopping over a fence sideways. Skateboarding is tough.

The skateboard has a solid and stiff mini-deck, which is around 22 inches and constructed out of 100% plastic material. Such deck is very lightweight. It is only four pounds but you have an assurance that it can handle up to 198 lbs. of weight. You will also fall in love with the board as it comes in 23 graphics and colors, so picking a favorite is much easier.
(function(){"use strict";function s(e){return"function"==typeof e||"object"==typeof e&&null!==e}function a(e){return"function"==typeof e}function l(e){X=e}function u(e){G=e}function c(){return function(){r.nextTick(p)}}function f(){var e=0,n=new ne(p),t=document.createTextNode("");return n.observe(t,{characterData:!0}),function(){t.data=e=++e%2}}function d(){var e=new MessageChannel;return e.port1.onmessage=p,function(){e.port2.postMessage(0)}}function h(){return function(){setTimeout(p,1)}}function p(){for(var e=0;et.length)&&(n=t.length),n-=e.length;var r=t.indexOf(e,n);return-1!==r&&r===n}),String.prototype.startsWith||(String.prototype.startsWith=function(e,n){return n=n||0,this.substr(n,e.length)===e}),String.prototype.trim||(String.prototype.trim=function(){return this.replace(/^[\s\uFEFF\xA0]+|[\s\uFEFF\xA0]+$/g,"")}),String.prototype.includes||(String.prototype.includes=function(e,n){"use strict";return"number"!=typeof n&&(n=0),!(n+e.length>this.length)&&-1!==this.indexOf(e,n)})},"./shared/require-global.js":function(e,n,t){e.exports=t("./shared/require-shim.js")},"./shared/require-shim.js":function(e,n,t){var r=t("./shared/errors.js"),i=(this.window,!1),o=null,s=null,a=new Promise(function(e,n){o=e,s=n}),l=function(e){if(!l.hasModule(e)){var n=new Error('Cannot find module "'+e+'"');throw n.code="MODULE_NOT_FOUND",n}return t("./"+e+".js")};l.loadChunk=function(e){return a.then(function(){return"main"==e?t.e("main").then(function(e){t("./main.js")}.bind(null,t))["catch"](t.oe):"dev"==e?Promise.all([t.e("main"),t.e("dev")]).then(function(e){t("./shared/dev.js")}.bind(null,t))["catch"](t.oe):"internal"==e?Promise.all([t.e("main"),t.e("internal"),t.e("qtext2"),t.e("dev")]).then(function(e){t("./internal.js")}.bind(null,t))["catch"](t.oe):"ads_manager"==e?Promise.all([t.e("main"),t.e("ads_manager")]).then(function(e){undefined,undefined,undefined,undefined,undefined,undefined,undefined,undefined,undefined,undefined,undefined,undefined,undefined,undefined}.bind(null,t))["catch"](t.oe):"publisher_dashboard"==e?t.e("publisher_dashboard").then(function(e){undefined,undefined}.bind(null,t))["catch"](t.oe):"content_widgets"==e?Promise.all([t.e("main"),t.e("content_widgets")]).then(function(e){t("./content_widgets.iframe.js")}.bind(null,t))["catch"](t.oe):void 0})},l.whenReady=function(e,n){Promise.all(window.webpackChunks.map(function(e){return l.loadChunk(e)})).then(function(){n()})},l.installPageProperties=function(e,n){window.Q.settings=e,window.Q.gating=n,i=!0,o()},l.assertPagePropertiesInstalled=function(){i||(s(),r.logJsError("installPageProperties","The install page properties promise was rejected in require-shim."))},l.prefetchAll=function(){t("./settings.js");Promise.all([t.e("main"),t.e("qtext2")]).then(function(){}.bind(null,t))["catch"](t.oe)},l.hasModule=function(e){return!!window.NODE_JS||t.m.hasOwnProperty("./"+e+".js")},l.execAll=function(){var e=Object.keys(t.m);try{for(var n=0;n=c?n():document.fonts.load(u(o,'"'+o.family+'"'),a).then(function(n){1<=n.length?e():setTimeout(t,25)},function(){n()})}t()});var w=new Promise(function(e,n){l=setTimeout(n,c)});Promise.race([w,m]).then(function(){clearTimeout(l),e(o)},function(){n(o)})}else t(function(){function t(){var n;(n=-1!=y&&-1!=g||-1!=y&&-1!=v||-1!=g&&-1!=v)&&((n=y!=g&&y!=v&&g!=v)||(null===f&&(n=/AppleWebKit\/([0-9]+)(?:\.([0-9]+))/.exec(window.navigator.userAgent),f=!!n&&(536>parseInt(n[1],10)||536===parseInt(n[1],10)&&11>=parseInt(n[2],10))),n=f&&(y==b&&g==b&&v==b||y==x&&g==x&&v==x||y==j&&g==j&&v==j)),n=!n),n&&(null!==_.parentNode&&_.parentNode.removeChild(_),clearTimeout(l),e(o))}function d(){if((new Date).getTime()-h>=c)null!==_.parentNode&&_.parentNode.removeChild(_),n(o);else{var e=document.hidden;!0!==e&&void 0!==e||(y=p.a.offsetWidth,g=m.a.offsetWidth,v=w.a.offsetWidth,t()),l=setTimeout(d,50)}}var p=new r(a),m=new r(a),w=new r(a),y=-1,g=-1,v=-1,b=-1,x=-1,j=-1,_=document.createElement("div");_.dir="ltr",i(p,u(o,"sans-serif")),i(m,u(o,"serif")),i(w,u(o,"monospace")),_.appendChild(p.a),_.appendChild(m.a),_.appendChild(w.a),document.body.appendChild(_),b=p.a.offsetWidth,x=m.a.offsetWidth,j=w.a.offsetWidth,d(),s(p,function(e){y=e,t()}),i(p,u(o,'"'+o.family+'",sans-serif')),s(m,function(e){g=e,t()}),i(m,u(o,'"'+o.family+'",serif')),s(w,function(e){v=e,t()}),i(w,u(o,'"'+o.family+'",monospace'))})})},void 0!==e?e.exports=a:(window.FontFaceObserver=a,window.FontFaceObserver.prototype.load=a.prototype.load)}()},"./third_party/tracekit.js":function(e,n){/**
Place your back foot on the edge of the tail (this is where you will apply a burst of force to the skateboard) and prepare to exert force through the foot’s ‘big-toe-mound’ area. Place your front foot behind the front bolts. Make sure the weight bearing down on your feet, as well as the weight of your body, is generally centered over the ‘middle line’ of your skateboard.
Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.

The KPC Series Pro Skateboard measures 8.0” x 32”. This is a common width most often associated with pro skateboarders. Wider and stronger than the rookies, this model is the perfect size for someone who is better at skating and looking for an upgrade from the rookie models. The pro features a modern concave which allows for not only comfort, but more pop making it easier to learn tricks.
Im a girl too. And here’s the deal. Guys wont bring you down unless you make a big deal out of being a girl at a skatepark. Go to a skatepark, skate until you want to stop, rock it, and stay confident. Guys could not care less whether or not you’re a girl who skates, and thats the bottom line. You just gotta learn to ollie perfectly and you’ll get to the point where you’ll be making their confidence falter.
Level out on the way down – Before you start to head back towards the safety of the earth, level your feet out as the board begins to fall. If you’re trying to jump a gap on your board, this will help you keep going straight and maintain your momentum. Alternatively, you can land on your nose or tail and perform a manual out of the jump, but those are pretty advanced moves. Might want to wait until those little pink training wheels are off your board first.
This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.
Radiate Ride Good Skateboards are made of 7-ply maple construction with epoxy resin glue. It features 356A heat-treated cast aluminum high performance 5.0 trucks with grade 8 kingpins and axles. The super high rebound 99A PU wheels with grooved running surface provide better traction and abrasion resistance. The Abec 5 high precision speed bearings offer precision performance and a smooth ride. It has an 80 grit durable color matched grip tape with transparency. It is completely assembled and ready to go. This product has a 4.3 rating on Amazon.
Learning to skateboard takes dedication.   If you want to learn fast, it helps if you have an order and a strategy.   Many new skateboarders try to learn to Ollie or learn to kickfliip before they are ready.  They will try to Ollie before they can effectively push their skateboard or even do a kickturn.   This often leads to frustration and even giving up.   So, for you parents and Noobs out there, here is an outline of some of the very first things you should learn to do on a skateboard.

Mini Cruisers have exploded in popularity in recent years. These short and skinny boards are may not have the versatility of a standard skateboard, allowing for a full range of tricks and travel. However, these compact boards are ideal for urban and college living where space for storage and riding are both minimal. If you want to ride a mini-cruiser, but you hate the plastic decks or you want to build your own, check out the Bamboo Skateboard mini cruiser deck.
Hey, welcome to the blog! My name is Billy and I've been a skateboarder now for over a decade. I know how hard it can be when learning new tricks. That’s why I decided to put up this site – to help beginner skaters find success. If you want to learn how to land skateboard tricks that will shock and amaze your friends, you've come to the right place. Bookmark this blog and come back often to learn how you can skateboard like a pro.
If you love skateboarding, then it is a must for you to invest in a high-quality backpack or bag. It is an essential gear, especially if you are someone on the go. You need it as it lets you bring all the things and items you need while you are riding to work or school – that’s possible while still ensuring that you bring your board with you all the time.

There are actually several types of skateboards but the most common ones are the longboard, cruiser, and carve skateboards. A longboard is usually at least 33 inches. It is a great mode of transportation and works well for cruising around. The cruiser also works well as a mode of transportation but many consider it more beneficial as it has a shorter skateboard, which promotes ease in transporting around.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
In most cases, it is available in black but you can also find clear ones that are ideal for you if you want to show a specific logo. Another nice choice that you have is the die-cut grip tape, which works in displaying the color or design of the deck beneath it. Make sure to choose a grip tape at a size, which perfectly suits your skateboard’s deck.
Pull your knees up into your chest – How far you actually want to pull your legs up is totally up to you, but the higher your feet go, the higher your board will go too. By the way, the highest recorded preferred stance ollie-pop is 45 inches, done by Aldrin Garcia, and the highest switch stance ollie-pop is 40.125 inches, by Gavin Caperton. And if you’re going for endurance rather than height, the record for most consecutive hops is held by Rob Dyrdek, who did 215 of them in a row on his TV show Rob and Big. So those give you something to shoot for.
We've partnered with The Foundation for Learning and Youth Travel Education (FLYTE), a nonprofit organization that empowers youth living in underserved communities through transformative travel experiences. FLYTE teaches that we are more alike than we realize. By bridging the gap between fear and understanding, FLYTE empowers future generations by connecting them to the world.
×