Ridge Skateboards For Beginners are a UK Brand and have taken over Europe. Now it is available in the U.S.A. exclusively through Amazon. The Deck measures 27″ long x 7.5″ wide (69cm x 19cm). It features 4″ wide high-performance trucks with 87A super soft yellow bushings. It is made of high quality secret plastic formula. It has a rating of 4.8 on Amazon.


My problem is that my board always lands crooked when I Ollie. The worst thing is that I even tell myself to “keep your shoulders straight” while I’m doing the Ollie and I still land crooked. I think it’s just hard for people to grasp the simple fact that everything on a skateboard has to be done horizontally which is odd because people don’t walk sideways. We walk straight. Like roller blading for example…. it’s easier for me to roller blade because I’m used to walking and running obviously except with a skateboard everything is as if you were hopping over a fence sideways. Skateboarding is tough.
Place your back foot on the edge of the tail (this is where you will apply a burst of force to the skateboard) and prepare to exert force through the foot’s ‘big-toe-mound’ area. Place your front foot behind the front bolts. Make sure the weight bearing down on your feet, as well as the weight of your body, is generally centered over the ‘middle line’ of your skateboard.

The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.
In the case that you didn't gave up after a hundred over tries, you'll start to develop a reaction to landing it. After a few hundred more tries, you'll feel you are getting off the ground and getting little air. And once you reach the thousandth try, you'll already be doing it whilst rolling and the next thousandth tries will be spent on clearing small cracks n obstacles and working towards ollieng up bigger obstacles n up ledges.
I’ve been skating for about 3-4 years, I can kickflip, pop shuv it, front shuv, 180 and almost heelflips. I can ollie and used to be very good at them and could get them clean, but when I started practicing kickflips, it made my slide all weird. I can still ollie ( though it’s not as clean) but now when I ollie I slide with my pinky toe and that region, instead of the side of my foot. How can I fix my slide? When I try practicing sliding with the side of my foot, it doesnt feel like I can turn my foot that far towards the board and when I do it slowly to see what im doing, i still slide with my toes.Thank you.

The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.


The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
Maybe you're new to skateboarding. We have lots of complete skateboards or longboards to get you started. All of our skateboard and longboard completes come fully assembled, so you can hit the streets without any of the hassle—try an Enjoi skateboard complete or check out our selection of Sector 9 longboard and skateboard completes. Or maybe you're an experienced skater looking to update and customize your ride. You probably want to start with the perfect skateboard deck before you do anything else. We carry high-quality skate decks to keep you steady and balanced while you bomb, slide, and carve the streets. We also have a variety of longboard decks in stock if you're looking for a smooth ride for cruising or commuting.
4 amazing skateboards in one nice lot. 1. 1990's Tony Hawk Conplete Skateboard, original falcon 3 design. With Rekon trucks and firelite classic wheels. 2. Sk8mafia Lucero deck. Signed by John Lucero. Brand new deck. 3. 1031 deck signed by entire team on a brand new creepy crawl deck. 4. Brand new super rare Big Mess deck with Blast design. This deck is extremely rare and is a must have for any collector. Both the signed decks are personalized to a guy named Jason that owned a skate shop here in Grant's Pass Or. Those guys were on his wall for a long time before he went out of business. If you have any questions or concerns please let me know. Thanks for looking. Steve
×