This board includes professional assembly. All Krown skateboards arrived assembled and ready to ride straight out the box. The Rookie model includes heavy duty Aluminum 5.0 trucks, 52mm 99A high-rebound urethane wheels, precision speed Abec 7 bearings, high tensile phillips head mounting hardware, and 80 grit black grip tape. Each component meets the industry standards and are a common choice of skaters worldwide.
The switch stance ollie uses a similar body motion, but the nollie is subtly distinct: For one, the rider is always moving forward, with the body positioned in a nollie stance--closer to the nose and with the front foot on the nose. Secondly the rider usually postures the body differently so as to compensate for this stance with respect to the forward motion. The rider presses the nose down using their front foot to engage the "pop" motion in order for the board to rise. This is In contrast to a "Fakie Ollie" where the pop motion is performed by the rear foot on the tail, similarly to a normal Ollie, however the rider is traveling backwards when performing a Fakie Ollie. Where in a Nollie the rider is traveling forward with their front foot on the nose to apply the initial force "pop".
The longboard, a common variant of the skateboard, is used for higher speed and rough surface boarding, and they are much more expensive. "Old school" boards (those made in the 1970s–80s or modern boards that mimic their shape) are generally wider and often have only one kicktail. Variants of the 1970s often have little or no concavity, whereas 1980s models have deeper concavities and steeper kicktails.[7]
The most important thing when you learn to skateboard is to skate with people that are at a higher skill lv than you, then they can tell you what you are doin wrong. Its so **cing anoing when you skate alle alone, wondering why your board is turning, and you haw to go to the internet to find out that it is something so easy as ceeping your shoulders straight.
EXPERIENCED SKATER! This board is amazing for the price! (notice i said FOR THE PRICE) At the time of this review, the board was $44.40 and for that price the board i got was phenomenal. It is a 7-ply deck with aluminum trucks (havent figured out the bearings but they definitely feel like the abec 5 they claim to be). The trucks arent the best quality out there and the board can be a little thinner (maybe 5-ply) but the overall board is amazing. There are only two complaints. The hole in the wheels is a tiny TINY TIIINYYY bit off center, but nothing that cant be fixed with a new set. I can see what another review said by it not coming assembled, as a couple of the bolts on the wheels are a little loose, but the board does come assembled.

Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
Since its humble beginnings, Element was created out of passion and an unwavering dedication to making a positive difference. The tree continues to grow while it respects its deepest roots and embraces the landscape of skateboarding, and the lifestyle that surrounds it. From team riders to advocates, and product to marketing, Element is all inclusive, whose mission is to lead not follow, and leave an imprint deep enough, that it continues to make the world a better place.
Hi, I can do an Ollie for 1 month already but somehow my Ollie is always unbalanced, meaning the front nose pops much higher than the back wheel. I understand that this is due to my front foot not sliding up higher, but I’m not sure how to correct it because my foot seem to get stuck after sliding up about an inch. Is it because of wrong technique or lack of calf muscles?
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Crouch down – While you’re standing on the board with your feet in the right position, crouch down closer towards the board. Don’t turn into a hunchback here; keep your back as straight as possible and don’t stick your rear out too far off the board, otherwise you’ll mess the whole thing up. Stay on the balls of your feet too; if you’re more on your toes, you’ll actually move the board in air and land off of it, and no one wants that. If you need to readjust your feet before you jump, just do a little micro-jump to reposition your feet, or shuffle into position. The first way is easier and faster, the second is more awkward and can mess up your shoes.
It wouldn’t be until the early 1980’s however, that a man named Rodney Mullen fully developed the skateboard ollie and brought it into vogue. Competing in the Rusty Harris contest in Whittier, California in 1982, Rodney Mullen used a back and forth motion on his skateboard to strike the back end of the board on the ground and using the front end to level the board out in mid-air – all from a flat surface. The audience’s jaws collectively hit the ground.
It is mainly because those items are guaranteed to help you familiarize yourself with the ins and outs of using them. They are a big help in making you feel comfortable when you push off with your feet while also balancing on top of the board when riding. It is not good to go for a very technical product, so it’s best to choose the mentioned types first.
×