The Quest Super Cruiser is made of Canadian Maple and measures 31″(787mm)x8″(203mm). It has a maximum capacity of 500 lbs. The wheels have a size of 1.99″(50mm)x1.42″(36mm) Pu with logo printing. The pattern is heat transferred. The trucks are 5″ heavy duty aluminum alloy. This skateboard can provide you a high-quality ride with an entry-level price. This is the best skateboard for both beginners and price-conscious expert skaters. It has an average rating of 4.3 on Amazon.
In the case that you didn't gave up after a hundred over tries, you'll start to develop a reaction to landing it. After a few hundred more tries, you'll feel you are getting off the ground and getting little air. And once you reach the thousandth try, you'll already be doing it whilst rolling and the next thousandth tries will be spent on clearing small cracks n obstacles and working towards ollieng up bigger obstacles n up ledges.
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
The Quest Super Cruiser is made of Canadian Maple and measures 31″(787mm)x8″(203mm). It has a maximum capacity of 500 lbs. The wheels have a size of 1.99″(50mm)x1.42″(36mm) Pu with logo printing. The pattern is heat transferred. The trucks are 5″ heavy duty aluminum alloy. This skateboard can provide you a high-quality ride with an entry-level price. This is the best skateboard for both beginners and price-conscious expert skaters. It has an average rating of 4.3 on Amazon.
The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.[5]
The wheels are also impressive. Unlike some other skateboards that have wheels that are quite stiff, causing them to feel like they will lock up when you ride on them, the wheels in this complete skateboard for beginners are smooth and comfortable. These are also easily controllable, so rest assured that they offer a smooth and friction-free glide.
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).
In general an axle width should be chosen that is close to the width of the deck it will be used with.[8] For example, a 7.75" wide deck will usually be fitted with trucks that have axles between 7.5" wide and 8.0" wide. (Standard truck axle nut size is 5/16"-24tpi UNF, and the thinner "jam" style with an optional nylon lock.) Trucks that are too wide can make doing tricks difficult and can cause the wheels to get in the way when the skateboard is being ridden. Trucks that are too small can be hard to maintain stability and can cause wheel bite to occur when turning.
New Arrivals Clothing T-Shirts Shirts Sweatshirts & Hoodies Jackets Sweaters Jeans Pants Joggers & Sweatpants Shorts Boardshorts Tank Tops Shoes Sneakers Boots Sandals Slippers Shoe Care Accessories Backpacks & Bags Watches Wallets Sunglasses Hats Beanies Socks Boxers Belts Skateboards Grooming Cologne Sun Care Jewelry Stickers Hydro Flask Deals Graphic Tees 2 for $30 RSQ Jeans BOGO 50% Off Joggers BOGO 50% Off Levi's $48.99 Flannels $24.99 Sweatshirts BOGO 50% Off Tees BOGO 50% Off Backpacks 30-50% Off Collections Brixton x Coors adidas x Beavis and Butthead Diamond Supply Co. x Family Guy Disney x Vans Nixon x Disney HUF x Peanuts Primitive x Rick and Morty Vans x Marvel adidas Watches Americana Asian Inspired Street Athletic Roses Tropical Prints Camo Stripes Tie Dye Checkerboard Party Prints College Tees Rick & Morty NASA Only at Tillys
No one had ever seen anything quite like it before, but no one knew just how transformative that moment would become. It wasn’t just that you could simply pop up into the air, it’s that it gave the rider a whole other set of opportunities to do tricks, and you don’t even have to be dependent on a ramp! As time went by, people began to add other skateboard tricks while they were airborne.

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
You can learn to ollie while standing stationary, or while your skateboard is rolling. Ollying while standing still works the same way as while rolling, but I think rolling ollies are easier than stationary ollies. If you would like to learn to ollie with your skateboard stationary, you can place your skateboard on some carpet or grass to keep it from rolling. If you prefer to learn to ollie while your skateboard is rolling, don’t go very fast at the start. Whichever way you learn to ollie, once you feel comfortable you should try to ollie the other way as well.
×