Almost is proud to announce a collaboration with Skateistan, the award-winning non-profit organization empowering children and youth through skateboarding and education. They recently launched a new Skate School in Phnom Penh, Cambodia on Friday (February 23rd, 2018). Over 100 children celebrated alongside special guests from around the world, including Almost flow skater Sky Brown. 
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
From cheap skateboards to high end, custom complete skateboard decks, we have boards for riders of every skill level and tax bracket - we get it, we put skateboarding before everything else first. If you can’t always afford a new board, but go through decks like toilet paper, consider a CCS Skateboard - they cost less, but are manufactured in the same factories as other brands we carry. CCS Skateboards are held to the same standards as every skateboard we sell, but we can sell them for less.
An Ollie is basically an upward/forward jumping trick. The name “ollie” comes from the nickname of Alan Gelfand who created the ollie in 1976. The ollie was then modified for flat-ground use by Rodney Mullen in 1982, and it is this flat-ground version of the ollie which is most commonly referred to as the ‘ollie’ today. The ollie is arguably the most important trick in skateboarding because it is the foundation of the majority of skateboard tricks which require lift. When you want to do a trick like the kickflip, when you want to get onto something like a ledge, or down something like a set of stairs, or try handrails, the ability to ollie is a necessity. Therefore the ability to ollie high and with good control is critical to your total skateboarding skill-set.

Skateboard hardware is used to connect the skateboard trucks to the skateboard deck. Skateboard hardware refers to the bolts and locknuts used when building a board. The bolts can have an Allen or Phillips head. Skateboard hardware comes in many different lengths, and often includes one different colored bolt so that the rider can mark the nose of their board.


James Haden is one of the owners of the Skateboarder community, together with Nash Gibson – his co-owner. He works as a full-time copywriter for a private company and also a true adventurer. He is an avid reader, writer, traveler, and extreme sports junkie. During his free time, he researches interesting content for their blog and continuously writes for their audience.
This board includes professional assembly. All Krown skateboards arrived assembled and ready to ride straight out the box. The Rookie model includes heavy duty Aluminum 5.0 trucks, 52mm 99A high-rebound urethane wheels, precision speed Abec 7 bearings, high tensile phillips head mounting hardware, and 80 grit black grip tape. Each component meets the industry standards and are a common choice of skaters worldwide.
The Quest Super Cruiser is made of Canadian Maple and measures 31″(787mm)x8″(203mm). It has a maximum capacity of 500 lbs. The wheels have a size of 1.99″(50mm)x1.42″(36mm) Pu with logo printing. The pattern is heat transferred. The trucks are 5″ heavy duty aluminum alloy. This skateboard can provide you a high-quality ride with an entry-level price. This is the best skateboard for both beginners and price-conscious expert skaters. It has an average rating of 4.3 on Amazon.
OneHype Designer Board has its own one of a kind design which is placed through a heat transfer and not a sticker. It measures 8″ W x 31″ L. It’s ready to use. It includes shock pads, durable wheels, smooth bearings, colored bushings, and aluminum trucks. The 7 ply maple deck is tough and can handle several impacts. This board is suitable for all ages.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
Mounting hardware is a set of eight 10-32 UNF bolts, usually an Allen or Phillips head, and matching nylon locknuts. They are used to attach the trucks (and any type of risers) to the board. Some sets have one different colored bolt to show which side is the nose of the skateboard. Hardware is available in various lengths for mounting trucks with or without risers.
GREAT board. Great design graphics. The boards deck has a real POP to it that makes it GREAT for tricks and a AWESOME beginner board. Only problem is It's super slow and requires a lot of work to maintain speed or to pick up speed period. A simple $20 wheel barring upgrade will fix that and BOOM PERFECT board, PERFECT caved in deck. Only 4 stars because of the lack of speed. I prefer my boards ready out of the box already pre-upgraded, but for the price, no point in complaining. Like almost all new boards, u have to ajust the wheels and the flex of the board to customize it to your liking. You won't regret it. But order it with some "Lucky" or "Red bearings" and your set.
×