So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
Hey, I’m a girl too and I’ve been skateboarding for nearly ten years now. I’m not a pro or anything, but I used to ride around in the local skatepark that was mainly just a big bowl that was fun to just drop into and cruise around in. I’m only just now learning street tricks. Anyways, I’d go there and the dudes would sometimes tease me, but sometimes they’d tease me about it. The thing you gotta do is not give up. Just ignore them. Dudes are stupid. Practice at home, by yourself, and learn some awesome stuff. So when you get really good, you can go to the park and if they start saying bad stuff, show off. It’ll blow them away. It always made me feel really good to show them that I was better than them right after they teased me for it.
If a skateboard deck is turned over to its design side, there are two complete T-shaped pieces of metal. This piece is attached to the skateboard deck with screws. The pin is a long piece of metal that is designed to turn the skateboard deck. Adjusting its tension affects the skateboard deck's turning sensitivity. Typically, longboards have looser tension than other skateboards to allow deeper turns.
It wouldn’t be until the early 1980’s however, that a man named Rodney Mullen fully developed the skateboard ollie and brought it into vogue. Competing in the Rusty Harris contest in Whittier, California in 1982, Rodney Mullen used a back and forth motion on his skateboard to strike the back end of the board on the ground and using the front end to level the board out in mid-air – all from a flat surface. The audience’s jaws collectively hit the ground.
Since its humble beginnings, Element was created out of passion and an unwavering dedication to making a positive difference. The tree continues to grow while it respects its deepest roots and embraces the landscape of skateboarding, and the lifestyle that surrounds it. From team riders to advocates, and product to marketing, Element is all inclusive, whose mission is to lead not follow, and leave an imprint deep enough, that it continues to make the world a better place.

The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
As you jump into the air, your front foot needs to roll slightly inward, and with the outside of your foot, you want to guide the skateboard as it flies into the air. Some people describe this as dragging the side of your front foot up the skateboard – that’s more or less what is happening, but what you are doing is using your shoe and the grip tape on the board to pull the skateboard higher into the air with you, and guiding the skateboard to where you want it.
We've partnered with The Foundation for Learning and Youth Travel Education (FLYTE), a nonprofit organization that empowers youth living in underserved communities through transformative travel experiences. FLYTE teaches that we are more alike than we realize. By bridging the gap between fear and understanding, FLYTE empowers future generations by connecting them to the world.

Velocity Boards Retro Banana Skateboard is a 22″ Complete Board Set with 6″ Aluminum Trucks, ABEC-7 Bearings, High-Quality Wheels, and Bushings. It is designed for maximum grip. The Deck measures about 22 x 6 x 4″. The truck Axle has a Width of 6″ and the Truck Hanger has a Width of 3″. It has a maximum load capacity of 176 lbs. (80 kgs.) It is best for skaters who are 6 years old and Up. It has an average Amazon rating of 4.7.


After that I went to my regular Olley spot to practice, fell so hard three times. My legs were so fucked up from the day before. Now I feel like shit because I had problem with a 20cm ledge I landed at least 100 times up and down yesterday. I’m even capable of 50cm ledges at slow speed, but I only get the front wheel and the board up so I have to put pressure on the nose to get it all the way up.
Low ollies: This can happen for a lot of reasons, but the biggest one is that you are not crouching low enough before your ollie, and not pulling your feet high enough after you jump. When you crouch down, try and touch the ground. When you jump, try to hit yourself in the chest with your knees. ​Both knees. Don’t worry about falling. That will happen sometimes – that’s just part of skateboarding! For more help, read the How Can I Make My Ollies Higher? FAQ
Large power is created at the point of action by applying small power to the point of effort. Application of this concept to skateboarding makes the back wheels the fulcrum, the tail the point of effort, and the nose the point of action. Applying power to the tail causes the nose to shoot upwards. When the front foot of the skater levels the nose at a point roughly horizontal to the ground in anticipation of the tail, soon to be leveled likewise by the skater’s back foot, the process smoothly done creates the illusion of the skateboard ‘sticking’ to the feet.
Invented in the late 1970s by Alan "Ollie" Gelfand, the ollie has become a skateboarding fundamental, the basis for many other more complicated tricks. In its simplest form, the ollie is a jumping technique that allows skaters to hop over obstacles and onto curbs, etc. What's so amazing about the ollie is the way the skateboard seems to stick to the skater's feet in midair. Seeing pictures of skaters performing soaring 4-foot ollies, many people assume that the board is somehow attached to the skater's feet. It's not. What's even more amazing about the ollie is that to get the skateboard to jump up, the skater pushes down on the board! The secret to this paradoxical maneuver is rotation around multiple axes. Let's take a closer look.

A skateboard is moved by pushing with one foot while the other remains on the board, or by pumping one's legs in structures such as a bowl or half pipe. A skateboard can also be used by simply standing on the deck while on a downward slope and allowing gravity to propel the board and rider. If the rider's leading foot is their right foot, they are said to ride "goofy;" if the rider's leading foot is their left foot, they are said to ride "regular." If the rider is normally regular but chooses to ride goofy, they are said to be riding in "switch," and vice versa. A skater is typically more comfortable pushing with their back foot; choosing to push with the front foot is commonly referred to as riding "mongo", and has negative connotations of style and effectiveness in the skateboarding community.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
500AlmostAluminatiArborBambooBirdhouseBlindBonzingCometCreatureDarkstarDB LongboardsDevilleDogtownDusters CaliforniaElementEnjoiEverseshFlipFocusFoundationGlobeGoldCoastGravityHabitatJartKebbekKrookedLandyachtzLaybackLushMadridMakahaMoonshine MFGOmenPennyPlan BPowell PeraltaPrism SkatePunkedRayneRealRememberRivieraRoad RiderSan ClementeSanta CruzSector 9Suicidal SkatesToy MachineWarehouseZ-FlexZero
Skateboarding, in one form or another, has been around since the late 1950’s when the first brave pioneer first attached roller skate wheels to a piece of wood. As skateboarding progressed to mimic surfing, skateboards evolved with the style of riding. Skateboards grew and changed shapes as riders experimented with everything from plastic to fiberglass to aluminum constructions - all in an effort to push what was possible. Like most sports or art forms, progression is at the heart of skateboard innovation.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
It's a neat piece of science art, and it also tells us something interesting. The arrows show us that the force on the skateboard is constantly changing, both in magnitude as well as in direction. Now the force of gravity obviously isn't changing, so the reason that these force arrows are shrinking and growing and tumbling around is that the skater is changing how their feet pushes and pulls against the board. By applying a variable force that changes both in strength and direction, they're steering the board.

This was a simple purchase. No issues at all and the skateboards are really nice! Some people have said it comes unassembled, that's not the case. I ordered 2 different boards and both came assembled and ready to roll.. The boards are topped with grip tape and trucks and wheels were assembled perfectly. If I had a need to get another board I would run straight back to this kit, they are great!


The skateboard has a solid and stiff mini-deck, which is around 22 inches and constructed out of 100% plastic material. Such deck is very lightweight. It is only four pounds but you have an assurance that it can handle up to 198 lbs. of weight. You will also fall in love with the board as it comes in 23 graphics and colors, so picking a favorite is much easier.
The KPC Series Pro Skateboard measures 8.0” x 32”. This is a common width most often associated with pro skateboarders. Wider and stronger than the rookies, this model is the perfect size for someone who is better at skating and looking for an upgrade from the rookie models. The pro features a modern concave which allows for not only comfort, but more pop making it easier to learn tricks.
GREAT board. Great design graphics. The boards deck has a real POP to it that makes it GREAT for tricks and a AWESOME beginner board. Only problem is It's super slow and requires a lot of work to maintain speed or to pick up speed period. A simple $20 wheel barring upgrade will fix that and BOOM PERFECT board, PERFECT caved in deck. Only 4 stars because of the lack of speed. I prefer my boards ready out of the box already pre-upgraded, but for the price, no point in complaining. Like almost all new boards, u have to ajust the wheels and the flex of the board to customize it to your liking. You won't regret it. But order it with some "Lucky" or "Red bearings" and your set.
×