Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
Popsicle - A Popsicle complete skateboard is typically between 30 and 34 inches in total length with a varying width between 6.0 inches wide and 9.25 inches wide. You can check out the deck size chart to pick the complete that will be best suitable for you. These decks all come with grip tape and are a more technical skateboard for tricks and for the skatepark. If you want to do more than cruise the streets, a Popsicle is what you are looking for. All of our complete skateboards include the deck, trucks, wheels, grip, bearings and hardware. They are all also fully assembled. When choosing a complete, typically the more expensive completes will include a higher quality deck, better and longer lasting trucks, upgraded wheels and a higher abec rating on the bearings.
Go for the low truck profile if you want to obtain additional stability when you do flip tricks. It also works well for small wheels. The mid-sized trucks are good for all-around use, especially in streets and parks. You can also choose the high-sized trucks that are good for carving and cruising, which is the reason why they are perfect for huge wheels.
Ridge Skateboards For Beginners are a UK Brand and have taken over Europe. Now it is available in the U.S.A. exclusively through Amazon. The Deck measures 27″ long x 7.5″ wide (69cm x 19cm). It features 4″ wide high-performance trucks with 87A super soft yellow bushings. It is made of high quality secret plastic formula. It has a rating of 4.8 on Amazon.

After that I went to my regular Olley spot to practice, fell so hard three times. My legs were so fucked up from the day before. Now I feel like shit because I had problem with a 20cm ledge I landed at least 100 times up and down yesterday. I’m even capable of 50cm ledges at slow speed, but I only get the front wheel and the board up so I have to put pressure on the nose to get it all the way up.


My son seems to have a lot of fun riding this skateboard. He will be out there doing tricks for hours. One evening when he took a break, I decided to see if I could still ride. When I took off down the driveway, I could feel how smoothly the wheels rolled. I used to have to pay extra for wheels like this when I was his age. Lost in thought, I coasted faster, and my neighbour didn't see me when I shot out of the driveway. Even though this thing flew several feet in the air, bounced, and came to rest more than 20 feet away, it had no visible damage! Not so for me. I loved the skateboard, but am now recovering from two broken ribs, torn neck cartilage, and a cracked pelvis. Still, this board rides like a dream!
But, a quick warning! If you learn to ollie while standing still, you can develop some bad habits. Some skaters end up turning in the air a little, and not landing straight. You might not even notice until you try to ollie while rolling. So, if you practice while standing still, I highly recommend also practicing while rolling. Maybe only practice in one spot for a few days - maybe a week or two - and then give the rolling ollie a shot. That way, if you are developing bad habits, you can shake them off before they really mess you up.
It wouldn’t be until the early 1980’s however, that a man named Rodney Mullen fully developed the skateboard ollie and brought it into vogue. Competing in the Rusty Harris contest in Whittier, California in 1982, Rodney Mullen used a back and forth motion on his skateboard to strike the back end of the board on the ground and using the front end to level the board out in mid-air – all from a flat surface. The audience’s jaws collectively hit the ground.
Choosing a skateboard deck is a great place to start when building a complete skateboard. Unless you have experience riding a shaped board - something a little more retro or unusual, we recommend you start with a popsicle shape. CCS carries over 60 different skateboard deck brands that sell this popular popsicle shape. If you have questions on what size you should ride or have any other questions about building a complete, we recommend you check out our Skateboard Buyer’s Guide. Here, you’ll find helpful how-to’s for choosing a skateboard decks, skateboard trucks, skateboard wheels, skateboard bearings, and skateboard components. This guide explains every part of a skateboard and helps you choose which sizes and styles to best suit your needs.

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.

No I don’t believe that. You have to feel your board with your toes and feel the shape that the board Under the bottom of your feet and then master the pop with this newly formed connection. Faster faster and more guts are needed. When you are going as fast as you can go and can Ollie perfectly with complete consistency you’ll Ollie everywhere even in the cold cold winter.


This was a simple purchase. No issues at all and the skateboards are really nice! Some people have said it comes unassembled, that's not the case. I ordered 2 different boards and both came assembled and ready to roll.. The boards are topped with grip tape and trucks and wheels were assembled perfectly. If I had a need to get another board I would run straight back to this kit, they are great!
I found that my problem was unclear instruction about the timing between jumping and popping. One day when I was watching a slowmo ollie video though, I noticed that the skateboarder already was beginning to jump (at least his body was already going in an upward motion) before snapping the board off the ground. That was a critical change I needed to make in order to get it working. I had been trying to pop the board while all my weight was still pushing down on it (kind of an obvious mistake, but I somehow overlooked this). Hope this helps somebody.
Skateboards can be bought online and in your local stores.  However, choosing a good skateboard can be challenging.  If you are a beginner there are a lot of things that you have to consider.  Aside from the cost, you should also check the entire board such as the wheels, the deck, the trucks, and others.  Here, we have compiled the best skateboards for sale that you can choose from right now.
The board also boasts of its reasonably small size and lightweight nature, making it easy to control and ride. In addition, carrying it wherever you want to go is also much easier because of its lightness. It is flexible enough that it can accommodate the needs of different kinds of users, including cruisers, travelers, beginners, expert riders, and kids.
The skater can gain greater clearance from the ground by jumping higher, popping faster, sliding the front foot farther forwards (starting the jump with the front foot farther back), and pulling the legs higher into the chest to raise the feet higher. Skaters attempting record-setting ollies even contort the legs so that board and feet are not directly below them, allowing the board to rise at or just below the level of the pelvis.
Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
The Bamboo Skateboards Galaxy Series Cosmic Cloud Skateboard Deck is an excellent option. This concave board is made exclusively of a bamboo hybrid, rather than pure maple. This means the deck is lighter, stronger, more flexible and can even absorb shock better. The non-carbonized, light-wood deck is made of 6-ply wood and is in its fourth generation of designs.

If you are new to skateboarding and are looking to build a custom skateboard complete, the best place to start is with the deck. While not all boards are created equal, groms will do well on just about any brand skateboard offered at CCS as durability really won’t come into play until riders start to skate bigger gaps and transition. So your focus should primarily be on finding the right deck width, board graphic, and brand that resonates with you or the rider.


So the proper foot placement for the ollie is with the ball of your back foot horizontal on the tail of your skateboard.  And your front foot centered on your board right behind the front trucks.  You may find that moving your feet around in different positions are more comfortable.  This is fine,  everybody can learn how to skateboard their own way.
Choosing a skateboard deck is a great place to start when building a complete skateboard. Unless you have experience riding a shaped board - something a little more retro or unusual, we recommend you start with a popsicle shape. CCS carries over 60 different skateboard deck brands that sell this popular popsicle shape. If you have questions on what size you should ride or have any other questions about building a complete, we recommend you check out our Skateboard Buyer’s Guide. Here, you’ll find helpful how-to’s for choosing a skateboard decks, skateboard trucks, skateboard wheels, skateboard bearings, and skateboard components. This guide explains every part of a skateboard and helps you choose which sizes and styles to best suit your needs.
This is how I learned how to ollie. Place your skateboard next to a curb, right up against it. This will help keep your board from rolling. Next, do everything that I just described, but don’t worry about what your board does. Just do it, and land up on top of the curb, on the sidewalk. Don’t stress about whether the skateboard will be there, or if you will get hurt – just go through the motions of ollying up the curb. If you do it right, the skateboard will be there. If you do it wrong, you’ll probably just land on your feet on the sidewalk. Here’s the key – just do it and expect it to work. Your body understands what you are trying to do, and the less you stress, the more it can kick in and fill in the blanks.
×