Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
Place your back foot on the edge of the tail (this is where you will apply a burst of force to the skateboard) and prepare to exert force through the foot’s ‘big-toe-mound’ area. Place your front foot behind the front bolts. Make sure the weight bearing down on your feet, as well as the weight of your body, is generally centered over the ‘middle line’ of your skateboard.
The Fakie is almost the same thing as a regular ollie-pop, but instead of going forward, the skater is going backwards when they pop the board up in the air, usually performed when you’re in a switch stance. A switch stance is when your feet are in the opposite stance of how you normally would stand, like when you write with your left hand instead of your right (if you’re right-handed).

The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.


Grip tape is a sheet of paper or fabric with adhesive on one side and a surface similar to fine sandpaper on the other. Grip tape is applied to the top surface of a board to allow the rider's feet to grip the surface and help the skater stay on the board while doing tricks. Grip tape is usually black, but is also available in many different colors such as pink, red, yellow, checkered, camo, and even clear. Often, they have designs die-cut to show the color of the board, or to display the board's company logo. Grip tape accumulates dirt and other substances that will inhibit grip, so use of a grip eraser or rubber eraser is necessary after riding through mud or with dirty shoes.


Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.

Also called the mounting hardware, the skateboard hardware is useful in connecting the trucks to the deck. Every truck is actually in need of 4 bolts and locknuts. If you are planning to buy hardware for your custom skateboard, then note that they are often sold in sets composed of 8 parts, though it is also possible for you to buy individual parts separately when required.
Sublimation (phase transition) is the transition of a substance directly from the solid to the gas phase without passing through an intermediate liquid phase. Sublimation is an endothermic phase transition that occurs at temperatures and pressures below a substance's triple point in its phase diagram. In this case, ink is transferred to a base layer, fibreglass for example, through heat and pressure, the result is a full color graphic that will not come off as easily as the more common heat transfers. This application is often found with bamboo boards and composite construction longboards where fibreglass can allow for various degrees of flex or stiffness depending on the ride you're looking for, cruising and carving versus slalom and downhill.
Save time and avoid the hassle of setting up a new skateboard by buying a complete that we’ll build for you. Skate One offers a full range of complete skateboards featuring high-performance wood and composite decks, grip tape, bearings, wheels, trucks, and hardware suitable for men, women, boys and girls of all ages, experience levels, and styles of skateboarding. Whether you're looking for a classic re-issue, cruiser, funshape, longboard, mini, street or skatepark style complete skateboard, we have you covered.
James Haden is one of the owners of the Skateboarder community, together with Nash Gibson – his co-owner. He works as a full-time copywriter for a private company and also a true adventurer. He is an avid reader, writer, traveler, and extreme sports junkie. During his free time, he researches interesting content for their blog and continuously writes for their audience.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
Get used to sliding your front foot up the length of the board. Once you’ve perfected lifting the front of the board up, use your back foot to hold the board in that position. Slide your front foot up the board towards the front, rotating it as you do so. The side of your foot just below the toes should grate along the deck of your board until it reaches the top.[5]

In the case that you didn't gave up after a hundred over tries, you'll start to develop a reaction to landing it. After a few hundred more tries, you'll feel you are getting off the ground and getting little air. And once you reach the thousandth try, you'll already be doing it whilst rolling and the next thousandth tries will be spent on clearing small cracks n obstacles and working towards ollieng up bigger obstacles n up ledges.


Popsicle - A Popsicle complete skateboard is typically between 30 and 34 inches in total length with a varying width between 6.0 inches wide and 9.25 inches wide. You can check out the deck size chart to pick the complete that will be best suitable for you. These decks all come with grip tape and are a more technical skateboard for tricks and for the skatepark. If you want to do more than cruise the streets, a Popsicle is what you are looking for. All of our complete skateboards include the deck, trucks, wheels, grip, bearings and hardware. They are all also fully assembled. When choosing a complete, typically the more expensive completes will include a higher quality deck, better and longer lasting trucks, upgraded wheels and a higher abec rating on the bearings.


The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.

The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
×