Both your height and weight should play an important role when you are choosing a skateboard. You need to find a skateboard, which fits your weight and height. Picking one, which is either too small or too big might only cause you to experience difficulty controlling it, especially if you are still a beginner learning the ins and outs of skateboarding.
The official record for the highest flat-ground ollie is 45′ (114.3cm) by Aldrin Garcia during the “Maloof High Ollie Challenge,” held on the 15th of February, 2011. You can watch the movie here. However, a groundbreaking moment in the lore of the ollie will always belong to Danny Wainwright’s ex record of 44.5′ (113.03cm, ELEMENT-HIGHEST OLLIE CONTEST Feb.6th,2000.) Reese Forbes, a competitor of Danny’s in this contest, was also well-known as a master of the ollie.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
A rushed take-off might be the problem here. Steps 2-4 of this trick tip could help you out. In order to make your feet “stick” to the board, you have to do the movement fluidly. But don’t stress yourself out! You should rather start with some preliminary exercises until you feel safe while ollieing. It is also important to pull your foot up to your board’s nose in a straight manner to prevent it from spinning.
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
Pull your knees up into your chest – How far you actually want to pull your legs up is totally up to you, but the higher your feet go, the higher your board will go too. By the way, the highest recorded preferred stance ollie-pop is 45 inches, done by Aldrin Garcia, and the highest switch stance ollie-pop is 40.125 inches, by Gavin Caperton. And if you’re going for endurance rather than height, the record for most consecutive hops is held by Rob Dyrdek, who did 215 of them in a row on his TV show Rob and Big. So those give you something to shoot for.
Ride like the pros with Tony Hawk skateboards, Airwalk skateboards and boards from Razor�, Kryptonics, Maple� and other trusted brands. These high-quality skateboards utilize smooth-rolling trucks and ball bearings that prevent jams and freezing as you shoot through the half-pipe or roll down the sidewalk. And while performance is your top consideration, all your tricks and moves will look even cooler with a board that's splashed with bright colors, emblazoned with attention-getting graphics and made with a sleek design. Choose from styles with bold patterns and detailed, full-color artwork that showcase your personal aesthetic along with your athleticism.
The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. Bushings come in varying shapes and urethane formulas as well as durometers, which may affect turning, rebound and durability. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability (useful when landing tricks). Standard kingpin nut size is 3/8" - 24tpi. The position of the hanger respect to the baseplate is also determined by the pivot, a rod that slots into the corresponding seat in the baseplate. The pivot stops the hanger from rotating around the kingpin. The pivot must allow some movement around the bushings and therefore is not a perfect fit. The space between the pivot and its seat in the baseplate is filled by a pivot cup, a plastic part that will take most of the wear and tear of the pivot and assist in centering the hanger needs to be lubricated every so often.
Regardless of your skill level, you definitely need quality skateboard parts and that begins with skateboard trucks. We carry hundreds of top-selling skate trucks! Hardcore skateboarders love our Independent skate trucks for their performance and durability. You can also pick out the perfect skateboard wheels, like a blazing fast set of Spitfires, and you'll be one step closer to skating like a pro. To make the most of your skate wheels, you'll need quality skate bearings, too—check out top-seller Bones Bearings. When building a skateboard, even the smallest choices make a difference, so be sure to get the right size skate hardware, double-check your skateboard bushings, and don't forget to grit up your board with grip tape.
Smile and wave – Feel free to look around at all the other people at the skatepark that stood by and marveled at your new-found accomplishments (all one of them). I’m sure by this point you’ll be picking up roses that are being thrown at your feet, and taking a well-deserved bow as they begin to chant your name. Take it all in, thank the crowd for their undying affection, and then go get a snow-cone. You deserve it, champ.
×