Position your front foot near the middle and your back foot on the tail – The best position is for the ball of your back foot to be slightly hanging off, and the front foot more towards the middle. The position of the front foot can change, however, depending on how much air you want to get: if you’re planning on doing a monster jump, move the front foot closer to the back; if you’re just hopping a little bit, move it closer to the front of the board itself. Beware though, the closer you move it towards the back foot, the harder the trick is to perform.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
GREAT board. Great design graphics. The boards deck has a real POP to it that makes it GREAT for tricks and a AWESOME beginner board. Only problem is It's super slow and requires a lot of work to maintain speed or to pick up speed period. A simple $20 wheel barring upgrade will fix that and BOOM PERFECT board, PERFECT caved in deck. Only 4 stars because of the lack of speed. I prefer my boards ready out of the box already pre-upgraded, but for the price, no point in complaining. Like almost all new boards, u have to ajust the wheels and the flex of the board to customize it to your liking. You won't regret it. But order it with some "Lucky" or "Red bearings" and your set.

New Arrivals Clothing T-Shirts Shirts Sweatshirts & Hoodies Jackets Sweaters Jeans Pants Joggers & Sweatpants Shorts Boardshorts Tank Tops Shoes Sneakers Boots Sandals Slippers Shoe Care Accessories Backpacks & Bags Watches Wallets Sunglasses Hats Beanies Socks Boxers Belts Skateboards Grooming Cologne Sun Care Jewelry Stickers Hydro Flask Deals Graphic Tees 2 for $30 RSQ Jeans BOGO 50% Off Joggers BOGO 50% Off Levi's $48.99 Flannels $24.99 Sweatshirts BOGO 50% Off Tees BOGO 50% Off Backpacks 30-50% Off Collections Brixton x Coors adidas x Beavis and Butthead Diamond Supply Co. x Family Guy Disney x Vans Nixon x Disney HUF x Peanuts Primitive x Rick and Morty Vans x Marvel adidas Watches Americana Asian Inspired Street Athletic Roses Tropical Prints Camo Stripes Tie Dye Checkerboard Party Prints College Tees Rick & Morty NASA Only at Tillys


Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
BRANDS Acembly adidas Amuse Society Asphalt Billabong Birkenstock Blue Crown Brixton Burton Calvin Klein Captain Fin Champion Charles and a Half Converse DGK Diamond Supply Co. Dickies Dr. Martens Electric Element Elwood Ethika FILA Fox Full Tilt G Shock Grizzly Herschel Supply Co. HippyTree Hoonigan HUF Hurley Hydro Flask Imperial Motion Ivy & Main JanSport Kendall & Kylie King Ice La Familia Last Call Co. Levi's Lira Loser Machine Lost LRG Neff New Balance Nike SB Nixon O'Neill OP Others Follow Patrons Of Peace Penny Pink Dolphin Popsockets Primitive Skateboarding PSD Puma Quiksilver Rainbow Rastaclat Ray Ban Rebel8 Reebok Reef Riot Society Rip Curl Roark Roxy RSQ Russell Athletic Rusty RVCA Salty Crew Santa Cruz Sky and Sparrow Soda Spy Stance Suavecito The North Face Timberland Tommy Hilfiger TOMS Under Armour Vans Vissla Vogue Eyewear Volcom Von Zipper Young & Reckless VIEW ALL BRANDS
A rushed take-off might be the problem here. Steps 2-4 of this trick tip could help you out. In order to make your feet “stick” to the board, you have to do the movement fluidly. But don’t stress yourself out! You should rather start with some preliminary exercises until you feel safe while ollieing. It is also important to pull your foot up to your board’s nose in a straight manner to prevent it from spinning.
Before we show you how to ollie, let’s get familiar with the legends that brought this skateboard trick to the masses.  If it were a person, the history of ollie would start way back in 1974, when Alan Gelfand got his first skateboard from his father after his family moved to Hollywood, Florida from New York state. It didn’t take him too long to get the hang of it; he won the South Florida Skateboard championships two years later.
It is a mini-cruiser, which is known for its strength as well as its ability to offer real value for the money you spent. This skateboard can also be expected to deliver an impressive performance – thanks to the Abec 7 skatro bearings used in it. There are also 59-mm urethane wheels and the 3-inch GOLD aluminum trucks that can help smoothen each ride.
Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.

No one had ever seen anything quite like it before, but no one knew just how transformative that moment would become. It wasn’t just that you could simply pop up into the air, it’s that it gave the rider a whole other set of opportunities to do tricks, and you don’t even have to be dependent on a ramp! As time went by, people began to add other skateboard tricks while they were airborne.


The Quest Super Cruiser is made of Canadian Maple and measures 31″(787mm)x8″(203mm). It has a maximum capacity of 500 lbs. The wheels have a size of 1.99″(50mm)x1.42″(36mm) Pu with logo printing. The pattern is heat transferred. The trucks are 5″ heavy duty aluminum alloy. This skateboard can provide you a high-quality ride with an entry-level price. This is the best skateboard for both beginners and price-conscious expert skaters. It has an average rating of 4.3 on Amazon.
There is no governing body that declares any regulations on what constitutes a skateboard or the parts from which it is assembled. Historically, the skateboard has conformed both to contemporary trends and to the ever-evolving array of stunts performed by riders/users, who require a certain functionality from the board. The board shape depends largely upon its desired function. Longboards are a type of skateboard with a longer wheelbase and larger, softer wheels.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.

Unlike golf or tennis, skateboarding is a sport where there isn’t a difference between the equipment needed for men and women to compete together. Women skate, flip and bruise just like the guys they’re at the skatepark with. The only consideration women may want to account for is that people who are shorter or smaller often want a shorter board for optimal control. The DAPANLA Skateboard Deck is a great deck that is slightly smaller, but can do it all.  


Are you on a hunt for the best skateboard on the market today? Then you are in the right place as this comprehensive article is designed to give you information about skateboarding and types of skateboards in general. By learning about the different types of skateboards and what each one can do, figuring out what works for you the best is a lot easier.
We've partnered with The Foundation for Learning and Youth Travel Education (FLYTE), a nonprofit organization that empowers youth living in underserved communities through transformative travel experiences. FLYTE teaches that we are more alike than we realize. By bridging the gap between fear and understanding, FLYTE empowers future generations by connecting them to the world.
Skateboarding is all about creativity and finding new challenges. A great way to explore skateboarding is to ride different shaped boards, wider trucks, and different size wheels. As you progress and start to ride new terrain and skate different kinds of spots, you may find one wheel size or board shape works better for you than another. There’s no wrong or right anything. There are no rules. Except for maybe one, and that is to keep skating. Skate as often as you can. Never is this more true than in the beginning while you’re developing your style and fundamentals.

500AlmostAluminatiArborBambooBirdhouseBlindBonzingCometCreatureDarkstarDB LongboardsDevilleDogtownDusters CaliforniaElementEnjoiEverseshFlipFocusFoundationGlobeGoldCoastGravityHabitatJartKebbekKrookedLandyachtzLaybackLushMadridMakahaMoonshine MFGOmenPennyPlan BPowell PeraltaPrism SkatePunkedRayneRealRememberRivieraRoad RiderSan ClementeSanta CruzSector 9Suicidal SkatesToy MachineWarehouseZ-FlexZero
Now, I might not be able to skate to save my life, but I can do a little physics. So here's a thought - maybe I can use physics to learn how to do an ollie. Here's the plan. I'm going to open up the above video of skateboarder Adam Shomsky doing an ollie, filmed in glorious 1000 frames-per-second slow motion, and analyze it in the open source physics video analysis tool Tracker.
Ride like the pros with Tony Hawk skateboards, Airwalk skateboards and boards from Razor�, Kryptonics, Maple� and other trusted brands. These high-quality skateboards utilize smooth-rolling trucks and ball bearings that prevent jams and freezing as you shoot through the half-pipe or roll down the sidewalk. And while performance is your top consideration, all your tricks and moves will look even cooler with a board that's splashed with bright colors, emblazoned with attention-getting graphics and made with a sleek design. Choose from styles with bold patterns and detailed, full-color artwork that showcase your personal aesthetic along with your athleticism.
For sale I have a Powell peralta old school ripper complete red and black with 169mm independent blackout trucks blue cambria 3md 62mm wheels and bones reds bearings The deck has only been skated twice with minor scrapes on the tail and wheel wells I added the independent blackout 69mm trucks and the Cambria wheels im selling it because I’m moving in a different direction I’m building a longboard for myself for this summer anyway the deck is a reissue ripper you can’t get it anymore great overall skater very durable
BRANDS Acembly adidas Amuse Society Asphalt Billabong Birkenstock Blue Crown Brixton Burton Calvin Klein Captain Fin Champion Charles and a Half Converse DGK Diamond Supply Co. Dickies Dr. Martens Electric Element Elwood Ethika FILA Fox Full Tilt G Shock Grizzly Herschel Supply Co. HippyTree Hoonigan HUF Hurley Hydro Flask Imperial Motion Ivy & Main JanSport Kendall & Kylie King Ice La Familia Last Call Co. Levi's Lira Loser Machine Lost LRG Neff New Balance Nike SB Nixon O'Neill OP Others Follow Patrons Of Peace Penny Pink Dolphin Popsockets Primitive Skateboarding PSD Puma Quiksilver Rainbow Rastaclat Ray Ban Rebel8 Reebok Reef Riot Society Rip Curl Roark Roxy RSQ Russell Athletic Rusty RVCA Salty Crew Santa Cruz Sky and Sparrow Soda Spy Stance Suavecito The North Face Timberland Tommy Hilfiger TOMS Under Armour Vans Vissla Vogue Eyewear Volcom Von Zipper Young & Reckless VIEW ALL BRANDS

Hey, welcome to the blog! My name is Billy and I've been a skateboarder now for over a decade. I know how hard it can be when learning new tricks. That’s why I decided to put up this site – to help beginner skaters find success. If you want to learn how to land skateboard tricks that will shock and amaze your friends, you've come to the right place. Bookmark this blog and come back often to learn how you can skateboard like a pro.
Ollie 180: an Ollie where the skateboarder and the skateboard spins 180 degrees after leaving the ground. Both the skateboarder and the skateboard rotate in the same direction (Frontside or Backside) with the skateboarder's feet sticking to the skateboard. This trick is usually referred to as a frontside or backside 180, or less frequently and more popular with older skateboarders and/or when performed on a bank/quarterpipe, a frontside / backside ollie
For sale I have a Powell peralta old school ripper complete red and black with 169mm independent blackout trucks blue cambria 3md 62mm wheels and bones reds bearings The deck has only been skated twice with minor scrapes on the tail and wheel wells I added the independent blackout 69mm trucks and the Cambria wheels im selling it because I’m moving in a different direction I’m building a longboard for myself for this summer anyway the deck is a reissue ripper you can’t get it anymore great overall skater very durable
Plan B sells boards with overall reliable attributes. They offer decks made from seven-ply wood. Powell is a longstanding company that founded the legendary Bones Brigade team, which kick-started Tony Hawk's career. Their skateboard designs change annually, but always look cool. Tony Hawk’s skate company is called Birdhouse. Their decks feature bird themes and have a thicker sixth layer of wood that makes it easier to jump and do flip tricks, which is ideal for vertical-style skateboarding. For environmentally-conscious skaters and fans of Bam Margera, buy a board from Element. They have variety on the technical side with their seven-ply boards and Helium decks. Their skateboards are made with an air pocket to be lightweight.

Punisher Skateboards Warphant measures 31 x 7.5 inch.  It has a 9-Ply Maple Black Board with Concave Deck and Double Kick Tail.  It comes with ABEC-3 Bearings, 5-inch V-style Heavy Duty Alloy Trucks, and Bases.  It uses 54 x 36 mm PU injection molded wheels and PE Riser Pad with PU Cushion and Punisher Logo.  It is perfect for learning and doing tricks.  It is best suited for riders who are 8 years old and above.  It has a 5 rating on Amazon.
To get higher ollies, I would suggesting resting your back foot on the very end of the tail and the front foot in the middle of the deck to allow for more slide. Popping as hard as you can and catching your board in the groove of the nose with you ankle practically resting in the groove will level the board out in the air. after this initial movement slide you feet back to the bolts on the tail and nose to ensure a clean landing.
×