When learning it, you will, slip and fall. Feel like an idiot doing something over and over again and not getting it, feel fear bcos you don’t know what's going to happen to you once you pop the tail, jump and slide your foot and then you land. Will you land on your board, will you be on the pavement? Will you slip out, will u kick the board away, will you land primo? No one knows but you gotta try it out and find it out yourself. Whatever it is, don't give up cos it's the strength to persevere, be crazy persistent to achieve and most of all being patient in learning and progressing that let's you earn the skateboarder title for your ownself.
This set-up is awesome for its price!!!! The wheels are nice and smooth (a little too big for my liking, but still good). The bearings are average (I replaced them with bones REDS). The trucks are nice and sturdy, but the bushings are kinda weak. The board is AUTHENTIC and of good dimensions. Finally, the griptape...they're all pretty much the same it's just the brand name that's different, so it doesn't matter it's all good. I would buy from this seller over and over again!!!!!!!
The following descriptions cover skateboard parts that are most prevalent in popular and modern forms of skateboarding. Many parts exist with exotic or alternative constructions. A traditional complete skateboard consists of the deck (often with griptape applied on top to enhance traction), trucks (with urethane bushings), wheels (with sealed bearings), bushings, nuts and bolts to fasten the truck and wheel assembly to the bottom of the deck. Older decks also included plastic parts such as side, tail, and nose guards.
Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
It is mainly because those items are guaranteed to help you familiarize yourself with the ins and outs of using them. They are a big help in making you feel comfortable when you push off with your feet while also balancing on top of the board when riding. It is not good to go for a very technical product, so it’s best to choose the mentioned types first.