The DreadXBoards Concave Skateboard has Plastic Deck Injection Molded for excellent durability. It features Urethane Wheels 59mm 78a, aluminum trucks, and Abec 7 Bearings. It is completely assembled and is ready to ride. It is perfect for beginners or experienced riders. It can load up to 185 lbs. It is great for kids and adults. It has an excellent rating of 4 on Amazon.
This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
Low ollies: This can happen for a lot of reasons, but the biggest one is that you are not crouching low enough before your ollie, and not pulling your feet high enough after you jump. When you crouch down, try and touch the ground. When you jump, try to hit yourself in the chest with your knees. ​Both knees. Don’t worry about falling. That will happen sometimes – that’s just part of skateboarding! For more help, read the How Can I Make My Ollies Higher? FAQ
Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?

The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Hey, I’m a girl too and I’ve been skateboarding for nearly ten years now. I’m not a pro or anything, but I used to ride around in the local skatepark that was mainly just a big bowl that was fun to just drop into and cruise around in. I’m only just now learning street tricks. Anyways, I’d go there and the dudes would sometimes tease me, but sometimes they’d tease me about it. The thing you gotta do is not give up. Just ignore them. Dudes are stupid. Practice at home, by yourself, and learn some awesome stuff. So when you get really good, you can go to the park and if they start saying bad stuff, show off. It’ll blow them away. It always made me feel really good to show them that I was better than them right after they teased me for it.
James Haden is one of the owners of the Skateboarder community, together with Nash Gibson – his co-owner. He works as a full-time copywriter for a private company and also a true adventurer. He is an avid reader, writer, traveler, and extreme sports junkie. During his free time, he researches interesting content for their blog and continuously writes for their audience.
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style. 
×