The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.


The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Land at the same time – Again, this is probably silly to repeat, but you’d be surprised to find out how many people execute a successful jump, and then throw their hands up in the air to celebrate their new-found triumph, and forget the most important part: landing. The best position for your feet to be in is as close to the trucks as possible. Don’t land too close to the nose or tail, or you could end up breaking off those the board itself. Also, remember to bend your knees to absorb the jump. Don’t want to land straight-legged: that’s how kneecaps are destroyed.

In the case that you didn't gave up after a hundred over tries, you'll start to develop a reaction to landing it. After a few hundred more tries, you'll feel you are getting off the ground and getting little air. And once you reach the thousandth try, you'll already be doing it whilst rolling and the next thousandth tries will be spent on clearing small cracks n obstacles and working towards ollieng up bigger obstacles n up ledges.
I have been doing ollie’s for about a year to a year and a halve, but thats not the problem. My problem is the board turns when i ollie, i cant help it, i am starting to go into harder ground (ollying off ledges and ollying stairs) but i cant land and ride away because my board has turned in a 45 degree angle and it jerks me off the board, Please help in all you can, cheers mate.
It wouldn’t be until the early 1980’s however, that a man named Rodney Mullen fully developed the skateboard ollie and brought it into vogue. Competing in the Rusty Harris contest in Whittier, California in 1982, Rodney Mullen used a back and forth motion on his skateboard to strike the back end of the board on the ground and using the front end to level the board out in mid-air – all from a flat surface. The audience’s jaws collectively hit the ground.
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car.  It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings.  It is ready to use and you can easily store it in your backpack.  It has an average rating of 4.5 on Amazon.
×