Shop skateboard decks from The House Outdoor Gear for the best selection of skateboard decks and everything else skateboarding. We carry the best skateboard brands around including Real, Baker, Blind, Zero, Enjoi, Welcome, Anti Hero and many more. Our site features skateboard wheels, skateboard trucks, skateboard bearings, and other skateboard accessories. From cruiser skateboards to traditional shapes the skateboard shop at The House Outdoor Gear will have something for everyone. Shop through our selection of the top skateboard decks and find what you’re looking for today.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
Jump – Ah yes, finally, we have reached the move itself. Basically, you have to do about twelve different things all at once to execute a successful ollie-pop: lift your front foot, press down with your back foot, angle your front ankle,  and jump. Lift the front foot off the ground first, and then move your back foot. This whole process is easier if you’re actually moving forward – since you don’t have to fight for balance – but it can be done while you’re standing still as well.
I have been doing ollie’s for about a year to a year and a halve, but thats not the problem. My problem is the board turns when i ollie, i cant help it, i am starting to go into harder ground (ollying off ledges and ollying stairs) but i cant land and ride away because my board has turned in a 45 degree angle and it jerks me off the board, Please help in all you can, cheers mate.
BRANDS Acembly adidas Amuse Society Asphalt Billabong Birkenstock Blue Crown Brixton Burton Calvin Klein Captain Fin Champion Charles and a Half Converse DGK Diamond Supply Co. Dickies Dr. Martens Electric Element Elwood Ethika FILA Fox Full Tilt G Shock Grizzly Herschel Supply Co. HippyTree Hoonigan HUF Hurley Hydro Flask Imperial Motion Ivy & Main JanSport Kendall & Kylie King Ice La Familia Last Call Co. Levi's Lira Loser Machine Lost LRG Neff New Balance Nike SB Nixon O'Neill OP Others Follow Patrons Of Peace Penny Pink Dolphin Popsockets Primitive Skateboarding PSD Puma Quiksilver Rainbow Rastaclat Ray Ban Rebel8 Reebok Reef Riot Society Rip Curl Roark Roxy RSQ Russell Athletic Rusty RVCA Salty Crew Santa Cruz Sky and Sparrow Soda Spy Stance Suavecito The North Face Timberland Tommy Hilfiger TOMS Under Armour Vans Vissla Vogue Eyewear Volcom Von Zipper Young & Reckless VIEW ALL BRANDS
go with friends like most do, or at least with friends that support what your doing. Im 26 yrs old,I am a solo skater in elk city Oklahoma and the skate community is small, but we have a park , but in the smaller community skaters clique up I didn’t grow up here so I’m left out. I learn a I can online and practice little bit s out of the day when I have time from both jobs I work, I just don’t get a lot of beef cause I ignore them and do my own thing , but I’ve noticed my tricks that I land alone fairly easy they get difficult in the presence of others for some reason Being standoffish and skate with a lil aggression you’ll be alright, just don’t give up man at all costs do not give up.
Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.
If you are completely new to skateboarding, consider taking a minute to read through the Skateboard Decks Section in our Buyer’s Guide will be helpful, but a good rule of thumb is: the bigger your feet, the wider your board should be. If you wear a size 9 and up, you can’t go wrong with buying an 8” board. Narrow boards are easier to flip while wider boards are more stable, but there are no hard and fast rules to skateboarding. The only way to really find out what you like is by trying new shapes, sizes, and brands. Brands like Welcome, Baker, Chocolate, Deathwish, and Element all have a wide variety of sizes, shapes, and graphics.
The DreadXBoards Concave Skateboard has Plastic Deck Injection Molded for excellent durability. It features Urethane Wheels 59mm 78a, aluminum trucks, and Abec 7 Bearings. It is completely assembled and is ready to ride. It is perfect for beginners or experienced riders. It can load up to 185 lbs. It is great for kids and adults. It has an excellent rating of 4 on Amazon.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.
The board is shaped like a cup in the center, and has whale tails on both ends, designed to make tricks easier to do. The blue stain on the board looks like the picture. It has a semi flat finish with no lacquer top coat. The underside is plain which allows the owner to add stickers and graphics if they want but they look great just the way they are.
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!
It's a neat piece of science art, and it also tells us something interesting. The arrows show us that the force on the skateboard is constantly changing, both in magnitude as well as in direction. Now the force of gravity obviously isn't changing, so the reason that these force arrows are shrinking and growing and tumbling around is that the skater is changing how their feet pushes and pulls against the board. By applying a variable force that changes both in strength and direction, they're steering the board.
EXPERIENCED SKATER! This board is amazing for the price! (notice i said FOR THE PRICE) At the time of this review, the board was $44.40 and for that price the board i got was phenomenal. It is a 7-ply deck with aluminum trucks (havent figured out the bearings but they definitely feel like the abec 5 they claim to be). The trucks arent the best quality out there and the board can be a little thinner (maybe 5-ply) but the overall board is amazing. There are only two complaints. The hole in the wheels is a tiny TINY TIIINYYY bit off center, but nothing that cant be fixed with a new set. I can see what another review said by it not coming assembled, as a couple of the bolts on the wheels are a little loose, but the board does come assembled.

Unlike golf or tennis, skateboarding is a sport where there isn’t a difference between the equipment needed for men and women to compete together. Women skate, flip and bruise just like the guys they’re at the skatepark with. The only consideration women may want to account for is that people who are shorter or smaller often want a shorter board for optimal control. The DAPANLA Skateboard Deck is a great deck that is slightly smaller, but can do it all.  
Hey, I’m a girl too and I’ve been skateboarding for nearly ten years now. I’m not a pro or anything, but I used to ride around in the local skatepark that was mainly just a big bowl that was fun to just drop into and cruise around in. I’m only just now learning street tricks. Anyways, I’d go there and the dudes would sometimes tease me, but sometimes they’d tease me about it. The thing you gotta do is not give up. Just ignore them. Dudes are stupid. Practice at home, by yourself, and learn some awesome stuff. So when you get really good, you can go to the park and if they start saying bad stuff, show off. It’ll blow them away. It always made me feel really good to show them that I was better than them right after they teased me for it.
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.
Save time and avoid the hassle of setting up a new skateboard by buying a complete that we’ll build for you. Skate One offers a full range of complete skateboards featuring high-performance wood and composite decks, grip tape, bearings, wheels, trucks, and hardware suitable for men, women, boys and girls of all ages, experience levels, and styles of skateboarding. Whether you're looking for a classic re-issue, cruiser, funshape, longboard, mini, street or skatepark style complete skateboard, we have you covered.
Krown burst on to the skate scene back in 1996 with the idea to provide a high quality skateboard to the rider on a budget. Krown recognized a big gap between the $20 big box retail skateboard and the $150 professional grade skateboard. The boards at big box retail stores have plastic wheels and don’t even roll! Krown’s idea to bring a price-point skateboard to the market that actually functions as a skateboard has proven to be successful after more than 20 years. With more than 20 years of industry knowledge and knowhow, Krown is able to source the best parts at the best prices, which allows Krown to pass the savings on to the consumer. This expertise has allowed Krown to venture into the world of skateboards, longboards, helmets, pads, and even tools. Krown is the best place to start for beginner and intermediate riders!
Crouch down – While you’re standing on the board with your feet in the right position, crouch down closer towards the board. Don’t turn into a hunchback here; keep your back as straight as possible and don’t stick your rear out too far off the board, otherwise you’ll mess the whole thing up. Stay on the balls of your feet too; if you’re more on your toes, you’ll actually move the board in air and land off of it, and no one wants that. If you need to readjust your feet before you jump, just do a little micro-jump to reposition your feet, or shuffle into position. The first way is easier and faster, the second is more awkward and can mess up your shoes.
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
My son seems to have a lot of fun riding this skateboard. He will be out there doing tricks for hours. One evening when he took a break, I decided to see if I could still ride. When I took off down the driveway, I could feel how smoothly the wheels rolled. I used to have to pay extra for wheels like this when I was his age. Lost in thought, I coasted faster, and my neighbour didn't see me when I shot out of the driveway. Even though this thing flew several feet in the air, bounced, and came to rest more than 20 feet away, it had no visible damage! Not so for me. I loved the skateboard, but am now recovering from two broken ribs, torn neck cartilage, and a cracked pelvis. Still, this board rides like a dream!
This set-up is awesome for its price!!!! The wheels are nice and smooth (a little too big for my liking, but still good). The bearings are average (I replaced them with bones REDS). The trucks are nice and sturdy, but the bushings are kinda weak. The board is AUTHENTIC and of good dimensions. Finally, the griptape...they're all pretty much the same it's just the brand name that's different, so it doesn't matter it's all good. I would buy from this seller over and over again!!!!!!!
Radiate Ride Good Skateboards are made of 7-ply maple construction with epoxy resin glue. It features 356A heat-treated cast aluminum high performance 5.0 trucks with grade 8 kingpins and axles. The super high rebound 99A PU wheels with grooved running surface provide better traction and abrasion resistance. The Abec 5 high precision speed bearings offer precision performance and a smooth ride. It has an 80 grit durable color matched grip tape with transparency. It is completely assembled and ready to go. This product has a 4.3 rating on Amazon.
A complete skateboard is pre-assembled - it almost rides right out of the package and on to the streets, ready for you to practice all your new tricks. You simply don’t have to think about buying the separate parts like trucks, wheels, decks or the likes. Once you have gained more experience on the board and you feel like customizing it to fit your skateboarding style, you can begin to learn more about the different pieces in order to assemble a skateboard that meets your specific wishes and demands. Until then, a complete can be quite the right choice.
The problem with wheel bite is that it tends to stop the motion of the wheels. This can result not only in a bad wipeout for the rider but also damage to the wheels. With the help of the riser pads, it is easier for you to preserve the deck of your skateboard since these pads can reduce the tendency of having stress cracks on where the trucks and deck meet.
The ollie is a fundamental trick in street skateboarding, and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many other tricks depend on it - for example the kickflip and heelflip - the ollie is often the first trick to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.
Aaron "Jaws" Homoki Aaron Herrington Aidan Campbell Al Davis Al Partanen Alec Majerus Alex Midler Alexis Sablone Andrew Brophy Andrew Reynolds Auby Taylor Austin Kanfoush Axel Cruysberghs Bam Margera Barney Page Ben Gore Ben Hatchell Ben Krahn Ben Raemers Ben Raybourn Billy Marks Blake Carpenter Bobby de Keyzer Bobby Worrest Boo Johnson Brad Cromer Brad McClain Brad Staba Brandon Biebel Brandon Westgate Brian "Slash" Hansen Brian Anderson Brian Delatorre Brian Downey Brian Lotti Bryan Herman Carlos Iqui Casper Brooker Caswell Berry Charlie Blair Chase Webb Chico Brenes Chima Ferguson Chopper Chris Cole Chris Gregson Chris Haslam Chris Joslin Chris Miller Chris Pfanner Chris Roberts Chris Russell Chris Troy Christian Hosoi Christian Maalouf Claus Grabke Clint Walker Clive Dixon Cody Lockwood Cody McEntire Cole Wilson Collin Provost Cooper Wilt Corey Duffel Corey O'Brien Cory Kennedy Craig "Questions" Scott Cyril Jackson Daan Van Der Linden Daewon Song Dakota Servold Dan Drehobl Dan Plunkett Dane Brady Dane Burman Dane Vaughn Daniel Castillo Daniel Lutheran Danny Cerezini Danny Falla Danny Garcia Danny Montoya Danny Renaud Danny Way Darren Navarrette Dave Abair Dave Caddo David Gonzalez David Gravette Davis Torgerson Dee Ostrander Dennis Busenitz Don "Nuge" Nguyen Dustin Dollin Ed Selego Ed Templeton Emmanuel Guzman Eric Dressen Eric Koston Erick Winkowski Erik Ellington Evan Smith Felipe Gustavo Frank Gerwer Frankie Hill Gilbert Crockett Glen Fox Grant Taylor Gustav Tonnesen Guy Mariano Henry Sanchez Hiroki Muraoka Hjalte Halberg Ishod Wair Jack Curtin Jack Given Jackson "Jacko" Shapiera Jackson Pilz Jake Hayes Jake Johnson Jam Douglas James Brockman Jamie Foy Jamie Lynn Jamie Palmore Jamie Tancowny Jamie Thomas Jarne Verbruggen Jason Adams Jason Jessee Javier Sarmiento Jay Adams Jeff Grosso Jeff Kendall Jeremy Leabres Jeron Wilson Jesse Narvaez Jesus Fernandez Jim Greco Jim Thiebaud Jimmy Cao Jimmy Lannon Jimmy Wilkins Joey Guevara Joey Pepper Johan Stuckey John Cardiel John Grigley John Lucero John Lupfer John Motta Jon Dickson Jon Nguyen Jordan Hoffart Jordan Maxham Jordan Sanchez Jordan Taylor Josef Scott Jatta Josh Kalis Josh Matthews Josh Pall Julian Davidson Julien Stranger Justin "Figgy" Figueroa Justin Brock Justin Eldridge Kellen James Kelvin Hoefler Kenny Anderson Kevin "Spanky" Long Kevin Baekkel Kevin Coakley Kevin Romar Kevin Taylor Kyle Leeper Kyle Nicholson Kyle Walker Lance Mountain Lee Yankou Leo Romero Leo Valls Leticia Bufoni Lewis Marnell Lizzie Armanto Louie Barletta Louie Lopez Madars Apse Mark "Gonz" Gonzales Mark Appleyard Marquise Henry Marshall Heath Mason Silva Matt Berger Matt Hensley Matt Tomasello Mike "Lizard King" Plumb Mike Anderson Mike Arnold Mike Carroll Mike McGill Mike Mo Capaldi Mike Vallely Miles Silvas Milton Martinez Morgan Smith Natas Kaupas Neen Williams Nestor Judkins Nick Boserio Nick Garcia Nicky Guerrero Nisse Ingemarsson Nora Vasconcellos Nyjah Huston Omar Hassan Oskar Rozenberg Hallberg P.J. Ladd Paul Grund Per Welinder Peter Hewitt Peter Ramondetta Phil Hansen Quim Cardona Raney Beres Raven Tershy Ray "Bones" Rodriguez Ray Barbee Raymond Molinar Rich Adler Rick Howard Rick McCrank Ricky Oyola Riley Hawk Rob Gonzalez Rob Roskopp Robbie Brockel Robbie Russo Rodney Mullen Rodrigo "TX" Teixeira Rodrigo Petersen Ronnie Sandoval Rowan Zorilla Rudy Johnson Ryan Decenzo Ryan Lay Ryan Reyes Ryan Spencer Ryan Townley Sam Beckett Sam Hitz Samarria Brevard Sammy Baca Scott Decenzo Sean Malto Sebo Walker Shawn Hale Silas Baxter-Neal Simon Isaksson Soy Panday Stefan Janoski Steve Caballero Steve Ortega Steve Saiz Stevie Perez Stevie Williams Stu Graham Sylvain Tognelli T.J. Rogers Taylor Kirby Terry Kennedy Thaynan Costa Theotis Beasley Tiago Lemos Tim O'Connor Tobin Valverde Tom Asta Tom Karangelov Tom Knox Tom Knox (80s) Tommy Fynn Tommy Guerrero Tommy Sandoval Tony Hawk Tony Karr Tony Trujillo Torey Pudwill Trevor McClung Tristan "Tfunk" Funkhouser Tyler Bledsoe Tyler Surrey Tyson Peterson Vincent Alvarez Vivien Feil Wade Desarmo Wes Kremer Wieger Van Wageningen Willis Kimbel Windsor James Yaje Popson Yonnie Cruz Yoshi Tanenbaum Youness Amrani Yuri Facchini Zach Lyons Zack Wallin Zered Bassett Zion Wright
go with friends like most do, or at least with friends that support what your doing. Im 26 yrs old,I am a solo skater in elk city Oklahoma and the skate community is small, but we have a park , but in the smaller community skaters clique up I didn’t grow up here so I’m left out. I learn a I can online and practice little bit s out of the day when I have time from both jobs I work, I just don’t get a lot of beef cause I ignore them and do my own thing , but I’ve noticed my tricks that I land alone fairly easy they get difficult in the presence of others for some reason Being standoffish and skate with a lil aggression you’ll be alright, just don’t give up man at all costs do not give up.
The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life. Core trucks are light weight and feature heavy duty aluminum with grade 8 steel kingpins and axles, as well as USA made bushings and pivot cups. 52mm 99A are the perfect wheels for both street and park skating. Like the name states, Amphetamine bearings are stimulants for your wheels! Light synthetic oil, Delrin Crowns, and Rubber Serviceable Shields are a few of the things that makes these bearings one of the best Abec 5 rated bearings on the market. Arrives un-assembled which allows for both customization and bonding time. Easy to assemble!

Sizing plays an important role in the performance of any deck. A large majority range in size from 7.75" to 8.5" in width. These will provide a great platform for shredding any obstacle and will excel in street and skatepark environments alike. For those who prefer a smaller board, decks are offered down to 7.5" in width- benefiting people with smaller feet or the technical skater. Conversely, those looking for a wider board will enjoy our selection ranging up to 8.9" wide. Larger decks will accommodate those with very large feet, as well as offer an amazing experience for cruising and shredding large ramps and transitions.

Penny Skateboards are available in 22", 27" and the 36" for different riding styles, skating abilities and personal preference. You can find a Penny board that's perfect for you and your skateboard needs. The 36" Penny Longboards allow you to carve up the streets, mountains or beach in style. Regardless of which size Penny is right for you, everyone needs a Penny skateboard to cruise on at the beach, the park, the shops or while on holidays.


I’m 31 and I just started skating too. I can ollie but they fluctuate a lot. I’ll do well certain day and certain day I won’t do well. It’s frustrating sometimes but I’m hooked. I go skating with my 5 year old son. He’s already practicing ollie. I think he’ll out do me soon. Man he picks up so fast like a sponge. Can’t wait till I can get all my basic tricks down so I can have more fun with them!
So you want to know how to ollie? Be warned, it’s not for the faint of heart, and a lot of people have tried and failed and tried some more and still failed and then eventually thrown their boards into a wall out of frustration (I have no idea who those people are). It’s by no means an easy skateboard trick, but if you want to know how to ollie, start with these simple tips:
Hey dude i want to push faster and constantly at the moment i am starting and stopping to much i would like to keep going is it because I’m not fit enough yet or am i not pushing correctly I’m regular stance…..should i put push down on my left knee while pushing for a while to keep my board straight?!!!! I also am trying to get my ollies down….. 🙂
You have all the time in the world to skate, but you don't have the time to build a skateboard yourself. Maybe it's just easier to get a complete skateboard than spend hours in the garage trying to screw on new trucks. Even though customization is awesome, it's not necessary. You just want the freedom of the ride. When you get your skateboard, you just want to be able to get out and ollie off the curb as fast as possible. Which is why Tillys has an awesome selection of complete skateboards for you. Choose from some of your favorite skateboard brands including Primitive and Element and more. The bottom graphics are probably the most important part, so you can definitely choose the one that best fits your style. Get your new complete skateboard right here.
A skateboard deck is made up of curved layers of wood that are combined with glue. Then, the skateboard deck is trimmed down to a board shape that is practical. Trucks are typically made of aluminum or other metal alloys. They are made by melted metal formed by a mold and later drilled into the skateboard deck. The wheels are formed the same way, but with polyurethane. They are attached by ball bearings to complete the product.
Sizing plays an important role in the performance of any deck. A large majority range in size from 7.75" to 8.5" in width. These will provide a great platform for shredding any obstacle and will excel in street and skatepark environments alike. For those who prefer a smaller board, decks are offered down to 7.5" in width- benefiting people with smaller feet or the technical skater. Conversely, those looking for a wider board will enjoy our selection ranging up to 8.9" wide. Larger decks will accommodate those with very large feet, as well as offer an amazing experience for cruising and shredding large ramps and transitions.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
!function(e){function n(t){if(r[t])return r[t].exports;var i=r[t]={i:t,l:!1,exports:{}};return e[t].call(i.exports,i,i.exports,n),i.l=!0,i.exports}var t=window.webpackJsonp;window.webpackJsonp=function(n,r,o){for(var s,a,l=0,u=[];l1)for(var t=1;td)return!1;if(p>f)return!1;var e=window.require.hasModule("shared/browser")&&window.require("shared/browser");return!e||!e.opera}function a(){var e="";return window.Q.sendErrorsToWeblogger&&"quora.com"==window.Q.subdomainSuffix&&(e+=[window.location.protocol,"//log.quora.com"].join("")),e+="/ajax/log_errors_3RD_PARTY_POST"}function l(){var e=o(h);h=[],0!==e.length&&c(a(),{errors:JSON.stringify(e)})}var u=t("./third_party/tracekit.js"),c=t("./shared/basicrpc.js").rpc;u.remoteFetching=!1,u.collectWindowErrors=!0,u.report.subscribe(r);var f=10,d=window.Q&&window.Q.errorSamplingRate||1,h=[],p=0,m=i(l,1e3),w=window.console&&!(window.NODE_JS&&window.UNIT_TEST);n.report=function(e){try{w&&console.error(e.stack||e),u.report(e)}catch(e){}};var y=function(e,n,t){r({name:n,message:t,source:e,stack:u.computeStackTrace.ofCaller().stack||[]}),w&&console.error(t)};n.logJsError=y.bind(null,"js"),n.logMobileJsError=y.bind(null,"mobile_js")},"./shared/globals.js":function(e,n,t){var r=t("./shared/links.js");(window.Q=window.Q||{}).openUrl=function(e,n){var t=e.href;return r.linkClicked(t,n),window.open(t).opener=null,!1}},"./shared/links.js":function(e,n){var t=[];n.onLinkClick=function(e){t.push(e)},n.linkClicked=function(e,n){for(var r=0;r>>0;if("function"!=typeof e)throw new TypeError;for(arguments.length>1&&(t=n),r=0;r>>0,r=arguments.length>=2?arguments[1]:void 0,i=0;i>>0;if(0===i)return-1;var o=+n||0;if(Math.abs(o)===Infinity&&(o=0),o>=i)return-1;for(t=Math.max(o>=0?o:i-Math.abs(o),0);t>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=0;r>>0;if("function"!=typeof e)throw new TypeError(e+" is not a function");for(arguments.length>1&&(t=n),r=new Array(s),i=0;i>>0;if("function"!=typeof e)throw new TypeError;for(var r=[],i=arguments.length>=2?arguments[1]:void 0,o=0;o>>0,i=0;if(2==arguments.length)n=arguments[1];else{for(;i=r)throw new TypeError("Reduce of empty array with no initial value");n=t[i++]}for(;i>>0;if(0===i)return-1;for(n=i-1,arguments.length>1&&(n=Number(arguments[1]),n!=n?n=0:0!==n&&n!=1/0&&n!=-1/0&&(n=(n>0||-1)*Math.floor(Math.abs(n)))),t=n>=0?Math.min(n,i-1):i-Math.abs(n);t>=0;t--)if(t in r&&r[t]===e)return t;return-1};t(Array.prototype,"lastIndexOf",c)}if(!Array.prototype.includes){var f=function(e){"use strict";if(null==this)throw new TypeError("Array.prototype.includes called on null or undefined");var n=Object(this),t=parseInt(n.length,10)||0;if(0===t)return!1;var r,i=parseInt(arguments[1],10)||0;i>=0?r=i:(r=t+i)<0&&(r=0);for(var o;r
×