Skateboards can be bought online and in your local stores.  However, choosing a good skateboard can be challenging.  If you are a beginner there are a lot of things that you have to consider.  Aside from the cost, you should also check the entire board such as the wheels, the deck, the trucks, and others.  Here, we have compiled the best skateboards for sale that you can choose from right now.
Today, many riders use the “ollie-pop” on more than just the flat-level surfaces in between other tricks, it’s used heavily in the half-pipe and bowl ramps to allow the rider to go even higher in the air. Performing the “ollie-pop” while you’re at or near the top of the lip is a great way to get an extra couple feet, which might be all you need to get that extra turn in and nail the 720 (or 900, if you’re Tony Hawk).
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
No one had ever seen anything quite like it before, but no one knew just how transformative that moment would become. It wasn’t just that you could simply pop up into the air, it’s that it gave the rider a whole other set of opportunities to do tricks, and you don’t even have to be dependent on a ramp! As time went by, people began to add other skateboard tricks while they were airborne.
Slide your front foot forward – You remembered to angle your front ankle right? Good, now use that to move your board forward in one big rolling motion, and bring your back leg up into your chest. All of this is done at the same time, but it takes practice to get the timing down. Don’t slide your foot out too early though, or you’ll end up with a pretty weak jump, but also, don’t slide it out too late, or it won’t get leveled and you’ll end up in the pavement. Come to think of it, just do it perfect the first time and everything will be great.
We've partnered with The Foundation for Learning and Youth Travel Education (FLYTE), a nonprofit organization that empowers youth living in underserved communities through transformative travel experiences. FLYTE teaches that we are more alike than we realize. By bridging the gap between fear and understanding, FLYTE empowers future generations by connecting them to the world.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.
For sale I have a Powell peralta old school ripper complete red and black with 169mm independent blackout trucks blue cambria 3md 62mm wheels and bones reds bearings The deck has only been skated twice with minor scrapes on the tail and wheel wells I added the independent blackout 69mm trucks and the Cambria wheels im selling it because I’m moving in a different direction I’m building a longboard for myself for this summer anyway the deck is a reissue ripper you can’t get it anymore great overall skater very durable

This can be tricky to figure out, so just take your time and relax. The first few times you try and ollie, it helps to not worry about this part. You will end up doing a sort of half-ollie, popping just a little in the air. Or, you might fall! But, don't worry, this is all part of learning. If you want though, you can certainly start with rolling your ankle when you try and ollie - whatever works for you! Eventually, you will need to roll and drag, and you'll figure it out. Just take your time!
Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?
Decks come in a variety of shapes and sizes. You can choose a mini-board, a cruiser, a drop-through or a standard deck for your favorite set of wheels and hardware. Widths range too from a few inches with a 22-inch board to the wide size of a true cruiser. Some decks are flat as possible while others are significantly concave for optimized turning. You can buy a deck with artwork and grip tape already attached for a quick install or you can get a bare-bones wooden deck to truly customize.
I’ve been skating for about 3-4 years, I can kickflip, pop shuv it, front shuv, 180 and almost heelflips. I can ollie and used to be very good at them and could get them clean, but when I started practicing kickflips, it made my slide all weird. I can still ollie ( though it’s not as clean) but now when I ollie I slide with my pinky toe and that region, instead of the side of my foot. How can I fix my slide? When I try practicing sliding with the side of my foot, it doesnt feel like I can turn my foot that far towards the board and when I do it slowly to see what im doing, i still slide with my toes.Thank you.
Ancheer 31″ Pro Skateboards are made of 7-ply maple wood and finished with anti-slip grip tape.  It includes 60mm PU wheels ideal for riders who want to carve out sections, obtain speed and higher off the ground for tricks. It features 6″ Tony Hawk Signature aluminum trucks and 32″ long deck with double kick tail which is ideal for perfecting your favorite tricks.  It comes with ABEC-7 skateboard bearings.  It has style and quality which is expected from the most influential skateboarders of all time.  It is one of the best-rated skateboards on Amazon with a rating of 4.8.
The fact that it has nice and attractive prints also makes it a fashion skateboard. You can use it to show not only your passion in the sport but also your fashion sense. It is also equipped with a high-density emery surface known for being both waterproof and non-slip. With that, you have a hundred percent assurance of your safety when you are riding on it.
Choosing a skateboard deck can be approached in a few different ways: you can choose your board based off the graphic, the brand, the shape, the width, or even the color. For most skateboarders, it’s a combination of all these factors, but if you’ve never skateboarded before, you may not know what shape, width, or brand you like best. In this case, choosing your favorite graphic would make total sense.

You have all the time in the world to skate, but you don't have the time to build a skateboard yourself. Maybe it's just easier to get a complete skateboard than spend hours in the garage trying to screw on new trucks. Even though customization is awesome, it's not necessary. You just want the freedom of the ride. When you get your skateboard, you just want to be able to get out and ollie off the curb as fast as possible. Which is why Tillys has an awesome selection of complete skateboards for you. Choose from some of your favorite skateboard brands including Primitive and Element and more. The bottom graphics are probably the most important part, so you can definitely choose the one that best fits your style. Get your new complete skateboard right here.
Hey guys. I’m having a real problem with shifting my ollies. I’ve taken videos of myself in slow-mo and asked people to tell me of my shoulders rotate. They said that they stay where they are. My board always turns whenever I ollie, up to 90 degree turns. I think it might be the way I slide my foot. I’ve noticed that it may circle behind me a bit. And I’ve tried to correct it but just can’t. Any help?
The board also boasts of its reasonably small size and lightweight nature, making it easy to control and ride. In addition, carrying it wherever you want to go is also much easier because of its lightness. It is flexible enough that it can accommodate the needs of different kinds of users, including cruisers, travelers, beginners, expert riders, and kids.
The Landwalker 22″ Complete Skateboard has a sturdy 7 layer Canadian maple deck. It’s best for downhill, U table and slider because of its enormous stability. This board is best for teens and adults. It comes with Abec 7″ Bearings, PU wheels, Black Grip Tape, and hardware. It measures 79 x 20 x 10 cm. This board is an awesome gift for Christmas or Halloween.
Made with bamboo and fiberglass, this board is tough, flexible and ready for anything. The construction is designed to feel and act like a snowboard. The drop-through design is perfect for freestyle longboarding, commuting, carving, pumping and more. It gives you better stability and more wheel clearance. The board is definitely best designed for carving but tricks and kicks are easily done as well.
In 1978, Alan Gelfand, who was given his nickname "Ollie" by Scott Goodman, learned to perform no-handed aerials in bowls and pools using a gentle raising of the nose and scooping motion to keep the board with the feet.[2][3] There are numerous references to Alan Gelfand's Ollie with most notably pictures in the 1970s skateboarding magazine "Skateboarder".

Bolted onto the underside of the tail end of a skateboard, the tail guard (also known as a "skid plate") protected the tail end from skid stops and other maneuvers that would otherwise wear away the wood (commonly known as razor tail) and decrease the longevity of the tail. Typically made of plastic, these were widely popular in the '80s but their usage quickly diminished with the arrival of two-tail board designs, which became increasingly popular in the '90s.
This board is an excellent option for beginners because of its simplicity and durability. The lightly concave design allows for simple turns but doesn’t require the rider to be an excellent navigator. You can start off riding this deck down the street and use it as you learn ollies, kickflips and how to drop in to a half pipe. It will withstand it all and look good doing it. 
Mounting hardware is a set of eight 10-32 UNF bolts, usually an Allen or Phillips head, and matching nylon locknuts. They are used to attach the trucks (and any type of risers) to the board. Some sets have one different colored bolt to show which side is the nose of the skateboard. Hardware is available in various lengths for mounting trucks with or without risers.
Penny Skateboards are available in 22", 27" and the 36" for different riding styles, skating abilities and personal preference. You can find a Penny board that's perfect for you and your skateboard needs. The 36" Penny Longboards allow you to carve up the streets, mountains or beach in style. Regardless of which size Penny is right for you, everyone needs a Penny skateboard to cruise on at the beach, the park, the shops or while on holidays.
In most cases, it is available in black but you can also find clear ones that are ideal for you if you want to show a specific logo. Another nice choice that you have is the die-cut grip tape, which works in displaying the color or design of the deck beneath it. Make sure to choose a grip tape at a size, which perfectly suits your skateboard’s deck.
Pop in your earbuds and head to the skate park with a skateboard that rolls through impressive stunts with ease. Most skateboards for sale offer strong wood decks that create a stable feel beneath your feet as you work on your grind and backslide techniques, but models with polypropylene construction offer a lightweight alternative with plenty of toughness. Try a surfboard-inspired design to cruise the streets like you'd ride a wave, or select a drop-through deck for smooth cruising. Grip tape promotes sure footing that helps you ride with confidence, but always put safety first - wear a skate helmet and skate pads from our Skateboard Shop for protection against mid-move falls.

Skateboards are for people who want to try something new and extreme.  If you have not given it a shot and you want to challenge yourself then you should try skateboarding.  It is a fact that there are certain risks that go along with skateboarding.  However, skateboarding can teach you to balance and it is also a great way of losing weight.  Skateboarding can also help you in making friends while you are in the park.  With skateboarding, you can learn perseverance and build confidence.
After you’ve properly applied a burst of force to the tail, the top-side of your front foot’s toe should start dragging up your board almost automatically. Eventually, the higher you are able to bring your front foot during lift will determine the apex of your ollie, so work gradually towards lifting your front foot as high as your body allows. Skateboarders who record the highest ollies usually (somehow manage to!) bring their feet higher than their hips!
The laws for skateboarding helmets vary from state to state. Many states require that skaters wear a helmet under a certain age, and some states like California make all skaters under 18 wear a CPSC Certified helmet at all times. CSPC skateboard helmets usually have an EPS protective liner that meets the safety standards for skateboarding. Make sure you check your state's regulations before ordering.
Almost is proud to announce a collaboration with Skateistan, the award-winning non-profit organization empowering children and youth through skateboarding and education. They recently launched a new Skate School in Phnom Penh, Cambodia on Friday (February 23rd, 2018). Over 100 children celebrated alongside special guests from around the world, including Almost flow skater Sky Brown. 

After that I went to my regular Olley spot to practice, fell so hard three times. My legs were so fucked up from the day before. Now I feel like shit because I had problem with a 20cm ledge I landed at least 100 times up and down yesterday. I’m even capable of 50cm ledges at slow speed, but I only get the front wheel and the board up so I have to put pressure on the nose to get it all the way up.


The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
×