The Rimable Complete 22″ Skateboard is the most compact street board that are ready-to-use.  It is best for exercise and fun, and very portable.  There are five colors that you can choose from Black, Blue, White, Purple, and Green.  It has high-quality construction, with a high-density plastic deck.  It features extremely smooth 59mm wheels along with ABEC7 bearings and solid aluminum trucks.  It measures 22″ long and 6″ wide and weighs 4 pounds.  It has the best rating of 4.3 on Amazon.
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car.  It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings.  It is ready to use and you can easily store it in your backpack.  It has an average rating of 4.5 on Amazon.
Cruiser - The name says it all. If you are looking to cruise around town then this is the right complete skateboard for you. These decks vary in length from between 20 inches all the way up to about 40 inches. The wheel diameters usually start at about 55 millimeters and use a much softer urethane than the previous Popsicle decks. These also come with all of the above but the decks do not always need grip tape. Some of the decks are plastic or composite material with grooves or gripping built directly into the deck mold. 
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
The good news is that majority of skate shoes today come with high-quality flat soles that are capable of providing the maximum surface area designed to let you come in contact to the board, thereby promoting better control. Look for a really durable shoe, which you can wear comfortably to guarantee a safe and enjoyable experience when you are skateboarding.

Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain. 

The Enjoi Whitey Panda deck features Resin 7 Construction. Resin 7 Construction uses 100% Canadian maple veneer with a specialized Epoxy resin Glue. These boards are individually pressed which helps insure you get the same concave and curvature in every deck - making your deck more consistent and your tricks more consistent. Why is it better? Compared to a traditional deck it's stronger and offers better pop and longer deck life.
Learning to skateboard takes dedication.   If you want to learn fast, it helps if you have an order and a strategy.   Many new skateboarders try to learn to Ollie or learn to kickfliip before they are ready.  They will try to Ollie before they can effectively push their skateboard or even do a kickturn.   This often leads to frustration and even giving up.   So, for you parents and Noobs out there, here is an outline of some of the very first things you should learn to do on a skateboard.
If you’re looking for complete skateboards that are ready to go, then you’ve come to the right place. We’ve got a great range of boards that you can ride right away, and with our next day delivery service, you’ll have your board before you know it. Browse our great selection, which includes iconic brands such as Flip, and an incredible range of colourful Penny boards and deck graphics. With so many to choose from, we’re confident you’ll find the complete skateboard you’re looking for. Buy online today and benefit for our speedy service.
The DreadXBoards Concave Skateboard has Plastic Deck Injection Molded for excellent durability. It features Urethane Wheels 59mm 78a, aluminum trucks, and Abec 7 Bearings. It is completely assembled and is ready to ride. It is perfect for beginners or experienced riders. It can load up to 185 lbs. It is great for kids and adults. It has an excellent rating of 4 on Amazon.
Ohderii Skate Skateboards are made of a High-quality Plastic deck which will not easily break even when pressed over by a car.  It comes with 3.125″ all aluminum alloy trucks, 59mm 78A super smooth PU wheels and ABEC-7 stainless steel bearings.  It is ready to use and you can easily store it in your backpack.  It has an average rating of 4.5 on Amazon.
×