Bolted onto the underside of the tail end of a skateboard, the tail guard (also known as a "skid plate") protected the tail end from skid stops and other maneuvers that would otherwise wear away the wood (commonly known as razor tail) and decrease the longevity of the tail. Typically made of plastic, these were widely popular in the '80s but their usage quickly diminished with the arrival of two-tail board designs, which became increasingly popular in the '90s.
The Landwalker 22″ Complete Skateboard has a sturdy 7 layer Canadian maple deck. It’s best for downhill, U table and slider because of its enormous stability. This board is best for teens and adults. It comes with Abec 7″ Bearings, PU wheels, Black Grip Tape, and hardware. It measures 79 x 20 x 10 cm. This board is an awesome gift for Christmas or Halloween.
The ollie is a fundamental skill in skateboarding and is used to leap onto, over, or off obstacles, or over gaps of unfriendly terrain such as grass or stairs. As so many tricks depend on it - for example the kickflip and heelflip - the ollie is often the first skill to be learned by a new skateboarder. The ollie typically takes considerable practice to learn.

So with your back foot, you want to kick the tail of your board down and right when it touches the ground you jump in the air off your back foot.  This is the ‘pop’.  It takes a little bit of getting used to but most beginners don’t really understand that initially, your back foot is doing most of the work.  Then bring your knees up to your chest after the jump, the higher up you pull your knees the higher up your skateboard can go!


Bolted onto the underside of the tail end of a skateboard, the tail guard (also known as a "skid plate") protected the tail end from skid stops and other maneuvers that would otherwise wear away the wood (commonly known as razor tail) and decrease the longevity of the tail. Typically made of plastic, these were widely popular in the '80s but their usage quickly diminished with the arrival of two-tail board designs, which became increasingly popular in the '90s.
Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
Mounting hardware is a set of eight 10-32 UNF bolts, usually an Allen or Phillips head, and matching nylon locknuts. They are used to attach the trucks (and any type of risers) to the board. Some sets have one different colored bolt to show which side is the nose of the skateboard. Hardware is available in various lengths for mounting trucks with or without risers.
The Wonnv Retro Mini Cruiser 22 inch Complete Skateboard is 22″ Light Up Clear Banana Skateboard.  It is complete with Light Up Board, Wheels, Metal Trucks, ABEC-7 Bearings, and High-Quality Bushings.  The set also includes 6″ Metal Trucks, High-Speed ABEC-7 Bearings, High-Quality Bushings, and Hardware.  It has a unique Textured Waffle Pattern on Deck and designed for Maximum Grip.  The Deck measures about 22 x 6 x 4″.  It has a 6″ Truck Axle and 3″ Truck Hanger.  It requires 2 AAA Batteries and is recommended for skaters who are 6 years old and Up.  It has a 5 rating on Amazon.
The Krown Rookie Skateboard Complete 7.5 comes with thick, sturdy 7-ply maple wood deck. It gives you more control and permits you to perform various tricks. It features carbon steel ABEC-3 bearings, aluminum trucks, bushings and 54mm x 34mm wheels. This board is perfect for kids who are 8 years and older. It has a maximum weight capacity of up to 220 lbs.
It is mainly because those items are guaranteed to help you familiarize yourself with the ins and outs of using them. They are a big help in making you feel comfortable when you push off with your feet while also balancing on top of the board when riding. It is not good to go for a very technical product, so it’s best to choose the mentioned types first.
Hey, I’m a girl too and I’ve been skateboarding for nearly ten years now. I’m not a pro or anything, but I used to ride around in the local skatepark that was mainly just a big bowl that was fun to just drop into and cruise around in. I’m only just now learning street tricks. Anyways, I’d go there and the dudes would sometimes tease me, but sometimes they’d tease me about it. The thing you gotta do is not give up. Just ignore them. Dudes are stupid. Practice at home, by yourself, and learn some awesome stuff. So when you get really good, you can go to the park and if they start saying bad stuff, show off. It’ll blow them away. It always made me feel really good to show them that I was better than them right after they teased me for it.
A skateboard consists of a deck, trucks, wheels, bearings, hardware, and griptape. All parts come in a variety of sizes, graphics, colors, and signature pro series. The deck is the essential part of any skateboard. The deck ranges generally from 7.5" to 8.5". Skaters choose their board size for many reasons, but the basic deciding factor comes down to style of skating and foot size. Transition skaters usually ride a wider deck, while street skaters tend to go with a smaller deck. Skate brands such as Girl, enjoi, and Welcome offer a wide range of boards in regards to sizes and graphics. Skateboard trucks come in either a high or low setting, and also in a range of widths. The main factors in a truck, are how well they turn, and how well they grind. Independent, Venture, and Thunder, are truck brands that are well known for their turning and grinding capabilities. The skate hardware is generally either Phillips head or Allen key bolts. The skateboard wheels range from 50mm to 60mm. Some brands offer smaller and larger sizes, but 50-60mm is the general range. Like the deck sizes, wheel sizes depend on the skater's choice of terrain: Transition skaters tend to ride bigger wheels, while street skaters usually go with smaller wheels. Bones, Spitfire, Ricta, and Wayward wheel companies all make wheels for any terrain, whether you're a street shredder or a park burner. Skate bearings follow the ABEC rating system, which includes grades 1, 3, 5, 7, and 9. Bones, Bronson, and Andale are some of the top bearing brands in the skate market. CCS proudly carries all these brands, and many more.
New Arrivals Men Backpacks & Bags Watches Wallets Sunglasses Hats Socks & Boxers Beanies Bandanas Belts Cologne Grooming Sun Care Jewelry Shoe Care SHOP ALL Women Backpacks Bags & Wallets Hats Belts Jewelry Sunglasses Watches Hair Accessories Socks & Tights Beauty SHOP ALL Phone & Tech Phone Accessories Tech Accessories Cameras Backpacks & Bags Backpacks Luggage & Duffle Bags Mini Backpacks Fanny Packs Lunch Bags Room & Home Kitchen & Drinkware Towels Inflatables Decor Pillows & Bedding Desk & School Supplies Novelties Stickers Patches Pins Keychains Air Fresheners Toys Toys & Plushes Blind Boxes Games Books Costumes & Masks Skateboards Longboard Skateboards Cruiser Skateboards Complete Skateboards Skate Accessories
The rider begins the ollie by crouching and jumping directly upward. As the rider begins to leap, instead of lifting the feet from the board, he/she "pops" the tail by striking it against the ground, which raises the board nose-first. Maintaining contact with the board, the rider lifts the front leg and bends the front ankle so that the outer or top side of the shoe slides towards the nose of the board. The friction between the shoe and the board's grip tape helps to guide and pull the board upward, while the rear foot only maintains slight contact with board to help guide it. When nearing the peak of the jump, the rider lifts the rear leg and pushes the front foot forward, which levels the board and keeps it in contact with the back foot.
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm (or 10mm depending on the axle), an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, followed by 3, 5, 7, and 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. Bearing performance is determined by how well maintained the bearings are. Maintenance on bearings includes periodically cleaning and lubricating them [1]. Bearings that are kept unmaintained have their performance greatly lowered and will soon need to be replaced. Bearing cleaning kits are commonly available on the market. The ABEC rating does not determine the speed or durability of a skateboard bearing. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic bearing balls, although other configurations are used as well.
Large power is created at the point of action by applying small power to the point of effort. Application of this concept to skateboarding makes the back wheels the fulcrum, the tail the point of effort, and the nose the point of action. Applying power to the tail causes the nose to shoot upwards. When the front foot of the skater levels the nose at a point roughly horizontal to the ground in anticipation of the tail, soon to be leveled likewise by the skater’s back foot, the process smoothly done creates the illusion of the skateboard ‘sticking’ to the feet.
Velocity Boards Retro Skateboards is a complete 22″ Banana Skateboard.  It includes 6″ Lightweight Aluminum Trucks, High-Speed ABEC-7 Bearings, High-Quality Wheels & Bushings and Hardware.  It has a Unique Textured Waffle Pattern on Deck and is designed for Maximum Grip.  The Deck measures about 22 x 6 x 4″.  It has a 6″ Truck Axle and a 3″ Truck Hanger.  It has a maximum weight capacity of  176 lbs. (80 kgs.).  It is great for all skaters who are 6 years old and above.  It has an Amazon rating of 4.7.
Just before a skater performs an ollie, there are three forces acting on the skateboard. One of these forces is the weight of the rider, shown here with two red arrows. Another is the force of gravity on the board itself, shown with a small black arrow. Finally, blue arrows show the force of the ground pushing up on the skateboard. These three forces balance out to zero. With no net force, the skateboard doesn't accelerate, but rolls along at a constant speed.
GREAT board. Great design graphics. The boards deck has a real POP to it that makes it GREAT for tricks and a AWESOME beginner board. Only problem is It's super slow and requires a lot of work to maintain speed or to pick up speed period. A simple $20 wheel barring upgrade will fix that and BOOM PERFECT board, PERFECT caved in deck. Only 4 stars because of the lack of speed. I prefer my boards ready out of the box already pre-upgraded, but for the price, no point in complaining. Like almost all new boards, u have to ajust the wheels and the flex of the board to customize it to your liking. You won't regret it. But order it with some "Lucky" or "Red bearings" and your set.
The KPC Series Pro Skateboard measures 8.0” x 32”. This is a common width most often associated with pro skateboarders. Wider and stronger than the rookies, this model is the perfect size for someone who is better at skating and looking for an upgrade from the rookie models. The pro features a modern concave which allows for not only comfort, but more pop making it easier to learn tricks.
Slam your back foot down on the tail of your skateboard as hard as you can. At that moment, you want to also jump into the air, off of your back foot. This part is key and takes practice. The trick is in getting your timing right. You want to slap the skateboard’s tail down, and as it hits the ground, jump off of that foot into the air. Make sure to pull that back foot high into the air. It's a quick, snapping motion.
×