Longboard - A longboard is similar to a cruiser in terms of overall use and getting around town. Longboards start at about 42 inches in length and about 9 inches in width. When you buy a longboard, the wheel base of the trucks is usually wider and they have wheels starting at roughly 60mm. This gives you more maneuverability and a very smooth ride.
The wheels of a skateboard are usually made of polyurethane, and come in many different sizes and shapes to suit different types of skating. Larger diameters (55–85 mm) roll faster, and move more easily over cracks in pavement and are better for transition skateboarding. Smaller diameters (48–54 mm) keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity which allows for a better response time, but also make for a slower top speed and are better for street skateboarding. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Again like car tires, wheels range from the very soft (about Shore A 75) to the very hard (about Shore A 101). As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer medium-sized wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are harder (A 100/A 101). Vertical ramp or "vert" skating requires larger wheels (usually 55–65 mm), as it involves higher speeds. Vert wheels are also usually slightly softer (A 98/ A 99), allowing them to maintain high speed on ramps without sliding. Slalom skating requires even larger wheels (60–75 mm) to sustain the highest speeds possible. They also need to be soft and have better grip to make the tight and frequent turns in slalom racing. Even larger wheels are used in longboarding and downhill skateboarding. Sizes range from 65 mm to 100 mm. These extreme sizes of wheels almost always have cores of hard plastic that can be made thinner and lighter than a solid polyurethane wheel. They are often used by skateboard videographers as well, as the large soft wheels allow for smooth and easy movement over any terrain.
In 1982, while competing in the Rusty Harris contest in Whittier, California, Rodney Mullen debuted an ollie on flat ground, which he had adapted from Gelfand's vertical version by combining the motions of some of his existing tricks. Mullen used a "see-saw" motion, striking the tail of the board on the ground to lift the nose, and using the front foot to level the board in mid-air. While Mullen was not initially impressed with his flat ground ollie, and did not formally name it, he realized it opened up a second, elevated plane on which to perform tricks.
If you’ve ever watched a skateboarder roll down the street and then all of a sudden pop into the air on a skateboard, you’re probably wondering the same question a lot of people do: how on earth do they do that? It almost seems magical how they just seem to explode off the ground, and then just kind of float. Skateboarder, meet, the ollie. It’s not in the category of “easy skateboard tricks,” but if you learn how to ollie, you’re well on your way to fame and fortune as a professional skater.
It looks simple but yet complicated and vice versa. It takes most weeks to months to learn n some even years but a lifetime of effort to be consistent and be perfect at it and able to go higher, faster and further. It is not a feat you achieve once and it can be thrown out of the window if you want to continue to skate well. I've know skateboarders who just does ollies, boned ollies, ollie north and ollie souths, fakie ollies, switch ollies and nollies and nothing else but everytime he's popping them over 3ft height and up ledges, over gaps and down stair sets or over handrails. So no one's gonna argue on that even though he's not bustin some new fangled pressure flip late flip revert or something. He gets mad street creds for those huge ollies.
I just can get any height on my ollie at all! so frustrating!, i can pop the board nicely and get it off the ground like that, but then i try to slide my foot up the board and it just stays at that 45 degree angle from when i popped it, i just can’t seem to slide and get it horizontal in the air, or any height for that matter, i have watched countless ollie tips and tricks videos, and practised for hours on end, the same ollie, i can ride smoothly and fine, along the side-walk for example but i just cant get any grip to bring my board up and forward (i bought a new skateboard yesterday, and also new shoes) so its obviously me which is incompetent in completing this ollie! I know im kind of waffling on a bit, but i just can get the board to get any height! Please help if you can!
go with friends like most do, or at least with friends that support what your doing. Im 26 yrs old,I am a solo skater in elk city Oklahoma and the skate community is small, but we have a park , but in the smaller community skaters clique up I didn’t grow up here so I’m left out. I learn a I can online and practice little bit s out of the day when I have time from both jobs I work, I just don’t get a lot of beef cause I ignore them and do my own thing , but I’ve noticed my tricks that I land alone fairly easy they get difficult in the presence of others for some reason Being standoffish and skate with a lil aggression you’ll be alright, just don’t give up man at all costs do not give up.
The wheels of your skateboard can greatly affect your ride in numerous ways, such as the speed, your ability to take control of the skateboard’s movements, and what you feel while riding the board. The good news is that they come in various sizes, levels of durability, and colors, allowing you to pick one that suits your skateboard preference and style.